NAVY UFGS-26 56 00-2013 EXTERIOR LIGHTING.pdf

《NAVY UFGS-26 56 00-2013 EXTERIOR LIGHTING.pdf》由会员分享，可在线阅读，更多相关《NAVY UFGS-26 56 00-2013 EXTERIOR LIGHTING.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-26 56 00 (May 2013)-Preparing Activity: NAVFAC SupersedingUFGS-26 56 00 (July 2006)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2013*SECTION TABLE OF CONTENTSDIVISION 26 - ELECTRICALSECTION 26 56 00EXTERIOR LIGHTING05/1

2、3PART 1 GENERAL1.1 REFERENCES1.2 RELATED REQUIREMENTS1.3 DEFINITIONS1.4 SUBMITTALS1.5 QUALITY ASSURANCE1.5.1 Drawing Requirements1.5.1.1 Luminaire Drawings1.5.1.2 Poles1.5.2 Pressure Treated Wood Pole Quality1.5.3 Photometric Plan1.5.4 Design Data for Luminaires1.5.5 LED Luminaire - IES LM-79 Test R

3、eport1.5.6 LED Light Source - IES LM-80 Test Report1.5.6.1 Test Laboratories1.5.7 Tests for Fiberglass Poles1.5.8 Regulatory Requirements1.5.9 Standard Products1.5.9.1 Alternative Qualifications1.5.9.2 Material and Equipment Manufacturing Date1.6 DELIVERY, STORAGE, AND HANDLING OF POLES1.6.1 Wood Po

4、les1.6.2 Concrete Poles1.6.3 Fiberglass Aluminum Steel Poles1.7 WARRANTY1.7.1 LED Luminaire Warranty1.7.2 Electronic Ballast Warranty1.8 OPERATIONAL SERVICEPART 2 PRODUCTS2.1 PRODUCT COORDINATION2.2 HID, LPS, FLUORESCENT, INDUCTION AND LED LUMINAIRES2.2.1 General Requirements2.2.2 Luminaire Light So

5、urcesSECTION 26 56 00 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.2.2.1 High Pressure Sodium (HPS) Light Sources2.2.2.2 Metal Halide (MH) Light Sources2.2.2.3 Low Pressure Sodium (LPS) Light Sources2.2.2.4 Fluorescent Light Sources2.2.2.5

6、 Induction Light Sources2.2.2.6 LED Light Sources2.2.3 Luminaire Ballasts, Generators and Power Supply Units (Drivers)2.2.3.1 HID Ballasts2.2.3.1.1 Electronic HID Ballasts2.2.3.1.2 Magnetic HID and LPS Ballasts2.2.3.2 Fluorescent Ballasts2.2.3.2.1 T5HO Electronic Fluorescent Ballasts2.2.3.2.2 T8 Ele

7、ctronic Fluorescent Ballasts2.2.3.2.3 Compact Fluorescent (CFL) Electronic Ballasts2.2.3.3 Induction Generators2.2.3.4 LED Power Supply Units (Drivers)2.2.4 LED Luminaire Surge Protection2.3 OBSTRUCTION MARKER LUMINAIRES2.4 EXTERIOR LUMINAIRE CONTROLS2.4.1 Photocell2.4.2 Timeswitch2.4.3 Lighting Con

8、tactor2.4.4 Lighting Control Relay Panel2.4.5 Motion Sensor2.4.6 Bi-level HID Controller2.5 POLES2.5.1 Concrete Poles2.5.1.1 Steel Reinforcing2.5.1.2 Tensioned Reinforcing2.5.1.3 Coating and Sleeves for Reinforcing Members2.5.1.4 Strength Requirement2.5.1.5 Shaft Preparation2.5.2 Aluminum Poles2.5.3

9、 Steel Poles2.5.4 Wood Poles2.5.5 Fiberglass Poles2.6 BRACKETS AND SUPPORTS2.7 POLE FOUNDATIONS2.8 EQUIPMENT IDENTIFICATION2.8.1 Manufacturers Nameplate2.8.2 Labels2.9 FACTORY APPLIED FINISHPART 3 EXECUTION3.1 INSTALLATION3.1.1 Wood Poles3.1.2 Concrete Poles3.1.3 Fiberglass Poles3.1.4 AluminumSteel

10、Poles3.1.5 Pole Setting3.1.6 Photocell Switch Aiming3.1.7 GROUNDING3.1.8 FIELD APPLIED PAINTING3.2 FIELD QUALITY CONTROL- End of Section Table of Contents -SECTION 26 56 00 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCES

11、A / NASA UFGS-26 56 00 (May 2013)-Preparing Activity: NAVFAC SupersedingUFGS-26 56 00 (July 2006)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2013*SECTION 26 56 00EXTERIOR LIGHTING05/13*NOTE: This guide specification covers lighting system requirements for

12、 exterior installations.This specification does not cover all possible methods or requirements for exterior lighting; therefore, designer should add special information required to suit a specific project. Industry publications exist to aid the designer in choosing the best lighting system for the p

13、roject. Publications include, but are not limited to, the Illuminating Engineering Society (IES) HB-10, LIGHTING HANDBOOK and RP-8, RECOMMENDED PRACTICE FOR ROADWAY LIGHTING.Adhere to UFC 1-300-02 Unified Facilities Guide Specifications (UFGS) Format Standard when editing this guide specification or

14、 preparing new project specification sections. Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective proje

15、ct, whether or not brackets are present.Comments, suggestions and recommended changes for this guide specification are welcome and should be submitted as a Criteria Change Request (CCR).*NOTE: TO DOWNLOAD UFGS GRAPHICSGo to http:/www.wbdg.org/ccb/NAVGRAPH/graphtoc.pdf.*NOTE: This section contains th

16、e following sketches (plates) and are available in metric (SI) and U.S. Customary (IP) system dimensions. Sketch titles and SECTION 26 56 00 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-style numbers are unchanged for both types.Do not inclu

17、de list of sketches, or sketches themselves, in project specifications. Use luminaire sketches as details (plates) on drawings whenever possible. If special features are required, do not modify sketches, but indicate these changes as notes in luminaire schedule. The “XL“ style numbers and dates shou

18、ld remain on the drawing details. If additional luminaire types are needed that are not covered in sketches, provide additional sketches or details on drawings, but do not label as XL sketch type.Sketch No. TitleXL-1 LED Roadway LuminaireXL-2 HID/Induction Roadway LuminaireXL-3 LED Area LuminaireXL-

19、4 HID Area LuminaireXL-5 Induction Area LuminaireXL-6 Low Pressure Sodium Area LuminaireXL-7 HID High Mast LuminaireXL-8 HID Apron/Large Sports Field LuminaireXL-9 HID Sports Field LuminaireXL-10 LED Pedestrian Post Top LuminaireXL-11 HID/CFL/Induction Pedestrian Post Top LuminaireXL-12 Decorative B

20、ollardXL-13 LED Parking Garage LuminaireXL-14 HID/Induction Parking Garage LuminaireXL-15 Exterior Recessed DownlightXL-16 LED Linear Wall WashXL-17 LED Wall PackXL-18 HID/Induction Wall PackXL-19 Decorative Wall SconceSECTION 26 56 00 Page 4Provided by IHSNot for ResaleNo reproduction or networking

21、 permitted without license from IHS-,-,-Sketch No. TitleXL-20 Aviation Obstruction LuminaireXL-21 LED Flood LuminaireXL-22 HID/Induction Flood LuminaireXL-23 Direct-Set Fiberglass PoleXL-24 Direct-Set Concrete PoleXL-25 Direct-Set Steel/Aluminum PoleXL-26 Anchor Base Fiberglass PoleXL-27 Anchor Base

22、 Steel/Aluminum PoleXL-28 Anchor Base Concrete PoleXL-29 Anchor Base Pole FoundationXL-30 Direct Set Pole Grounding DetailXL-31 Luminaire Mounting Arm DetailsXL-32 Luminaire Mounting Arm DetailsXL-33 Luminaire Mounting Bracket DetailsXL-34 Luminaire Mounting Bracket DetailsNOTE: Do not include this

23、index in project specification.*NOTE: The following information shall be shown on the project drawings or specified in the project specifications:a. Luminaire schedule indicating luminaire type, mounting, and light source type and quantity;b. Accessories required, such as photocell, mounting bracket

24、s or arms and pole type;c. Wattage, operating voltage and frequency;d. Location and mounting height of poles or standards;e. Referenced XL sketch or detail;f. NEMA distribution type and BUG rating when SECTION 26 56 00 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted withou

25、t license from IHS-,-,-applicable; andg. Extent and location of the work to be accomplished with wiring and equipment necessary for a complete installation.*NOTE: Demolition work that involves disposal of fluorescent and HID light sources and ballasts will require the use of Section 02 84 16 HANDLIN

26、G OF LIGHTING BALLASTS AND LAMPS CONTAINING PCBs AND MERCURY.*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organi

27、zation, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.Referenc

28、es not used in the text will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to in the

29、 text by the basic designation only.ALLIANCE FOR TELECOMMUNICATIONS INDUSTRY SOLUTIONS (ATIS)ATIS ANSI O5.1 (2008) Wood Poles - Specifications Errata 2009; Amendment 1 2010; Amendment 2 2011) Standard Specifications for Structural Supports for Highway Signs, Luminaires and Traffic SignalsSECTION 26

30、56 00 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR-CONDITIONING ENGINEERS (ASHRAE)ASHRAE 189.1 (2011; Errata 2012; Errata 2012; Errata 2013) Standard for the Design of High-Performance Green

31、 Buildings Except Low-Rise Residential BuildingsASHRAE 90.1 - IP (2010; Errata 1-3 2011; INT 1-12 2011; Addenda A, B, C, G, H, J, K, O, P, S, Y, Z, BZ, CG, CI and DS 2012; Errata 4-8 2012; INT 13-16 2012; Errata 9-10 2013) Energy Standard for Buildings Except Low-Rise Residential BuildingsASHRAE 90.

32、1 - SI (2010; Errata 1-2 2011; INT 2-12 2011; Addenda A, B, C, G, H, J, K, O, P, S, Y, Z, BZ, CG, CI and DS 2012; Errata 3-9 2012; INT 13-16 2012; Errata 10-11 2013) Energy Standard for Buildings Except Low-Rise Residential BuildingsAMERICAN WOOD PROTECTION ASSOCIATION (AWPA)AWPA U1 (2012) Use Categ

33、ory System: User Specification for Treated WoodASTM INTERNATIONAL (ASTM)ASTM A123/A123M (2012) Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM A153/A153M (2009) Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareASTM B108/B108M (2

34、012; E 2012) Standard Specification for Aluminum-Alloy Permanent Mold CastingsASTM B117 (2011) Standard Practice for Operating Salt Spray (Fog) ApparatusASTM C1089 (2013) Standard Specification for Spun Cast Prestressed Concrete PolesASTM G154 (2012) Standard Practice for Operating Fluorescent Light

35、 Apparatus for UV Exposure of Nonmetallic MaterialsCALIFORNIA ENERGY COMMISSION (CEC)CEC Title 24 (2008; Effective Jan 2010) Californias Energy Efficiency Standards for Residential and Nonresidential BuildingsILLUMINATING ENGINEERING SOCIETY OF NORTH AMERICA (IES)IES HB-10 (2011) IES Lighting Handbo

36、okSECTION 26 56 00 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IES LM-79 (2008) Electrical and Photometric Measurements of Solid-State Lighting ProductsIES LM-80 (2008) Measuring Lumen Maintenance of LED Light SourcesIES RP-16 (2010; Addend

37、um A 2008; Addenda B Errata 2004; R 2005; Errata 2007) Roadway LightingIES TM-15 (2011) Luminaire Classification System for Outdoor LuminairesIES TM-21 (2011) Projecting Long Term Lumen Maintenance of LED Light SourcesINSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS (IEEE)IEEE 100 (2000; Archived)

38、The Authoritative Dictionary of IEEE Standards TermsIEEE C2 (2012; Errata 2012; INT 1-4 2012) National Electrical Safety CodeIEEE C62.41 (1991; R 1995) Recommended Practice on Surge Voltages in Low-Voltage AC Power CircuitsIEEE C62.41.1 (2002; R 2008) Guide on the Surges Environment in Low-Voltage (

39、1000 V and Less) AC Power CircuitsIEEE C62.41.2 (2002) Recommended Practice on Characterization of Surges in Low-Voltage (1000 V and Less) AC Power CircuitsNATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)ANSI ANSLG C78.41 (2006) For Electric Lamps-Guidelines for Low-Pressure Sodium LampsANSI ANS

40、LG C78.42 (2009) For Electric Lamps: High-Pressure Sodium LampsANSI C136.13 (2004; R 2009) American National Standard for Roadway Lighting Equipment, Metal Brackets for Wood PolesANSI C136.21 (2004; R 2009) American National Standard for Roadway and Area Lighting Equipment - Vertical Tenons Used wit

41、h Post-Top-Mounted LuminairesANSI C136.3 (2005; R 2009) American National Standard SECTION 26 56 00 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-for Roadway and Area Lighting Equipment Luminaire AttachmentsANSI C78.1381 (1998) American Natio

42、nal Standard for Electric Lamps - 250-Watt, 70 Watt, M85 Metal-Halide LampsANSI C82.4 (2002) American National Standard for Ballasts for High-Intensity-Discharge and Low-Pressure Sodium (LPS) Lamps (Multiple-Supply Type)ANSI/ANSLG C78.43 (2007) American National Standard for Electric Lamps - Single-

43、Ended Metal-Halide LampsANSI/NEMA C78.LL 1256 (2003) Procedures for Fluorescent Lamp Sample Preparation and the Toxicity Characteristic Leaching Procedure (TCLP)NEMA 250 (2008) Enclosures for Electrical Equipment (1000 Volts Maximum)NEMA ANSLG C78.377 (2011) American National Standard for Electric L

44、amps Specifications for the Chromaticity of Solid State Lighting ProductsNEMA ANSLG C78.380 (2007) Electric Lamps - High Intensity Discharge Lamps, Method of DesignationNEMA ANSLG C78.44 (2008) For Electric Lamps - Double-Ended Metal Halide LampsNEMA ANSLG C82.11 (2011) Lamp Ballasts - High-Frequency Fluorescent Lamp BallastsNEMA ANSLG C82.14 (2006) Lamp Ballasts Low-Frequency Square Wave Electronic Ballasts - for Metal Halide LampsNEMA C136.10 (2010) American National Standa