NAVY MS22033 REV F (1)-2005 BELT AIRCRAFT SAFETY LAP《折叠式航空器安全带》.pdf

《NAVY MS22033 REV F (1)-2005 BELT AIRCRAFT SAFETY LAP《折叠式航空器安全带》.pdf》由会员分享，可在线阅读，更多相关《NAVY MS22033 REV F (1)-2005 BELT AIRCRAFT SAFETY LAP《折叠式航空器安全带》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET BELT, AIRCRAFT SAFETY, LAP Inactive for new design after 30 September 1997. This specification is approved for use by the Naval Air Systems Command, and is available for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the p

2、roduct described herein shall consist of this specification sheet and MIL-R-81729. FIGURE 1. Belt assembly. RIGHT SIDE OF BELT (SEE FIGURE 5) 45.00 + 1.00 AT MAXIMUM ADJUSTMENT FOR -6 40.00 + 1.00 AT MAXIMUM ADJUSTMENT FOR -5 54.00 + 1.00 AT MAXIMUM ADJUSTMENT FOR -4 AMSC N/A 1 of 5 FSC 1680LEFT SID

3、E OF BELT (SEE FIGURE 2)MS22033F (AS) w/AMENDMENT 106 June 2005 SUPERSEDING MS22033F (AS) 26 July 2004 INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22033F (AS) w/AMENDMENT 1 2 TABLE I. Superseding belt assemblies. 1/ MS22033-1, -2, and

4、 -3 are canceled. Existing stock should be used until exhausted. CANCELED BELT ASSEMBLY DASH NO. SUPERSEDING BELT ASSEMBLY DASH NO. MS22033-1 MS22033-4 MS22033-2 MS22033-5 MS22033-3 MS22033-6 PROTECTOR 62A92B7 WASHER AN960 RIVET NASM20615-4CU7 2 EACH REQD. ADJUSTER MS22004-1 STITCH LATCH ASSY MS3488

5、 SMOOTH SIDE OF PROTECTOR PULL TAB 75 + .124.004.50 + .256.0012.00LOOP PIA-PS22010-2 LABELCC.25 .50WEBBING FOR -4 (60 INCHES LONG BEFORE STITCHING) WEBBING FOR -5 (48 INCHES LONG BEFORE STITCHING) WEBBING FOR -6 (53 INCHES LONG BEFORE STITCHING) FIGURE 2. Left side of belt.CB BAA1/Provided by IHSNot

6、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22033F (AS) w/AMENDMENT 1 3 STITCHSTITCH WITH SIZE E NYLON THREAD, 8 TO 10STITCHES PER INCH .12 3.00 WIDTH REF .19 .75 .44 1.00 WIDTH REF .12 .12 .31 3.38 .50 FIGURE 3. View B-B. FIGURE 4. View A-A. STITCH (SEE FIGURE

7、2) 4.50 + .25 6.00 .75 + .12 LINK PIA-PS22003-1ADJUSTER MS22004-1 12.00 4.00 PULL TABA A C C LABEL WEBBING FOR -4 (60 INCHES LONG BEFORE STITCHING) WEBBING FOR -5 (48 INCHES LONG BEFORE STITCHING) WEBBING FOR -6 (53 INCHES LONG BEFORE STITCHING) LOOP PIA-PS22010-2 FIGURE 5. Right side of belt (for d

8、imensions not shown, see figure 2). B BProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22033F (AS) w/AMENDMENT 1 4 * Label shall be in accordance with MIL-DTL-32075, type VI, class 11. FIGURE 6. View C-C. NOTES: 1. Material: a. Webbing, nylon, PIA-

9、W-27265, type IX-R, sage green. b. Pull tab, nylon, PIA-W-4088, type II, class 1, or PIA-T-5038, type IV, sage green. c. Pocket, nylon, PIA-T-5038, type II, sage green. d. Thread, nylon, V-T-295, type I, # 6 cord, sage green. e. Thread, nylon, V-T-295, type I, size E, sage green. 2. Finish: Material

10、 dyed sage green shall be a visual match to FED-STD-595, sage green, # 34158 or 34159. All stitching shall be in accordance with ASTM-D6193, type 301, and be not less than 4 nor greater than 6 stitches per inch except as noted. Ends of stitching shall be backstitched a distance of not less than inch

11、. Stitching shall be with nylon thread, # 6 cord except as noted. 3. Unless otherwise specified, dimensions shall be in inches. Tolerance: decimals + .06. 4. Referenced documents shall be of the issue in effect on the date of invitation for bid or request for proposal. 3/32 (TYP) BELT, AIRCRAFT SAFE

12、TY, LAP PART NUMBER MS22033-( ) CONTRACT NO. MANUFACTURER NAME AND DATE (MONTH - YEAR) LABEL* FOR DASH NO. SEE TABLE I AS REQUIRED WEBBING.875 1.250 MAXSTITCH(SEE FIGURE 2).094 MIN .125 MIN 3.00 MAX.094 (TYP) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

13、HS-,-,-MS22033F (AS) w/AMENDMENT 1 5 5. For design feature purposes, this specification sheet takes precedence over procurement documents referenced herein. 6. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done

14、as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previo

15、us issue. Preparing Activity: Navy - AS (Project 1680-2005-002) NOTE: The activity listed above was interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-