NAVY MIL-V-29601-1994 VEST SURVIVAL CMU-30 P22P-15《CMU-30 P22P-15救生背心》.pdf

《NAVY MIL-V-29601-1994 VEST SURVIVAL CMU-30 P22P-15《CMU-30 P22P-15救生背心》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-V-29601-1994 VEST SURVIVAL CMU-30 P22P-15《CMU-30 P22P-15救生背心》.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、*.J v. MIL-V-29bOL 9999906 L995693 bLq IINCH-POUNDI MIL-V-29601 (AS) 15 December 1994 MILITARY SPECIFICATION VEST, SURVIVAL, CMU-30/P22P-15 This specification is approved for use by the Naval Air Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the

2、 Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the general requirements and inspections for one type of survival vest designed to accommodate soft and hard body armor. 1.2 Classification. The Aircrew Integrated Survival Armor Protection (AISAP) vests shall be one of the follow

3、ing sizes (see 6.2b): Medium Large 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed

4、in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2e). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed

5、 to: Commander, Systems Standardization, Code 4.1.11B120-3, Naval Air Warfare Center Aircraft Division, Highway 547, Lakehurst, NJ 08733-5100, by using the self- addressed Standardization Document Improvement Proposal(DD Form 1426) appearing at the end of this document or by letter. AMSC-N/A FSC 841

6、5 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling Services flIL-V-29bOL m 999990b L995b94 550 m MIL-V-29601(AS) SPECIFICATIONS FEDERAL V-F-106 UU-P-268 PPP-T-4 5 MILITARY MIL-R-3390 MIL-C-3953 MIL-W-4088 MIL-T-5038 MIL-W-5664 MIL-C-7

7、219 MIL-K-8662 MIL-B-17757 MIL-F-21840 STANDARDS MILITARY MIL-STD-105 MIL-STD-129 MS20230 MS22018 MS22020 MS27980 M527983 MS51940 Fastener, Slide, Interlocking Paper, Kraft, Wrapping Tape, Gummed, Paper Reinforced and Plain, for Sealing and Securing Ring, Dee Cloth, Duck, Nylon (Validated) Webbing,

8、Textile, Woven Nylon Tape, Textile and Webbing, Textile, Reinforcing, Nylon Webbing, Textile, Elastic (Validated) Cloth, Duck, Nylon Knife, Hunting, Sheathed, Survival, Pilots (Validated) Boxes, Shipping, Fiberboard (Modular Sizes) Fastener Tapes, Hook ana, Pile, Synthetic Sampling Procedures and Ta

9、bles for Inspection by Attributes Marking for Shipment and Storage Grommet, Metallic, Plain and Spur, with Washer, Type I and Type III (Validated and Reinstated) Snap, Parachute Harness Quick Fit Ejector Link, Parachute Harness Triangle (Validated) Fastener, Snap, Style 2 (Regular Wire Spring Clamp

10、Type) Fastener, Snap, Style 4 (Validated) Loop, Slide (For Equipage) (Unless otherwise specified, copies of federal and military specifications and standards are available from DODSSP, Standardization Document Order Desk, 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA 19111-5094). 2.1.2 Government d

11、rawinss. The following Government drawings form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation (see 6.2). 2 Licensed by Information Handling ServicesMIL-V-27601 m 7777706 1995b95 497 D MIL-V-29601(AS) NAVAL AIR SYSTE

12、MS COMMAND DRAWINGS 823AS100 3241AS301 3241AS302 3241AS303 3241AS304 3241AS305 3241AS306 3241AS307 3241AS308 3241AS309 3241AS310 3241AS311 3241AS312 3241AS313 3241AS314 3241AS315 3241AS316 3241AS317 3241AS390 3241AS391 3241AS392 Dee-Ring Assembly, Snaplink, Rescue Survival Vest Assembly, Survival. V

13、est Sub-Assembly, Securing Belt Assembly, Torso Harness Assemblies, Flashlight Strap Assembly, Chemlite Pocket Assembly, Heed Pocket Assembly, Survival Item Pocket Assembly, Day/Night Flare Pocket Assembly, Sea Dye Marker Pocket Assembly, Survival Knife Pocket Assembly, Pengun Flare Signal Kit Pocke

14、t SRU-31/P Medical Pocket Assembly, SDU-5/5 Light Storage Pocket Assembly, CMU-30/P22P-15 AN/PRC Radio Pocket Assembly, CMU-30/P22-15 D-Ring Retaining Flap Assembly, CMU-30/P22P-15 Identification Label, CMU-30/P22P-15 Mesh Vest Patterns, Size Medium, CMU-30/P22P-15 Mesh Vest Patterns, Size Medium, C

15、MU-30/P22P-15 Pocket Patterns, CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-3O/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 CMU-30/P22P-15 (Unless otherwise specified, copies of drawings required by

16、 contractors in connection with specific acquisition functions should be obtained from the contracting activity, or as directed by the contracting officer.) 2.2 Non-Government publication. The following document forms a part of this document to the extent specified herein. Unless otherwise specified

17、, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified issues of documents 3 Licensed by Information Handling Servicesnot listed in the DODISS are the issues of the documents cited in the solicitation (see

18、 6.2e). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D3951 - Packaging, Commercial (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) 2.3 Order of Precedence. In the event of a conflict between the text of th

19、is document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Oualification. The vests furnished under this Specificat

20、ion shall be products which are authorized by the qualifying activity for listing on the applicable qualified products list at the time of award of contract (see 4.3 and 6.4). Qualification of any one size assembly, under this specification, will automatically qualify a supplier for all sizes specif

21、ied herein (see 1.2). 3.2 First article. When specified (see 6.2f), a sample shall be subjected to first article inspection (see 6.5) in accordance with 4.4. 3.3 Materials and components. The materials and components shall conform to applicable specifications, standards, and drawings and shall be as

22、 specified herein. Equivalent materials and parts require approval by the Naval Air Warfare Center Aircraft Division Warminster (Code 603), Warminster, Pennsylvania 18974-0591. Requests for use of equivalent items shall be submitted to the Contracting Officer. 3.3.1 Mesh Vest. The mesh vest shall be

23、 fabricated in accordance with Naval Air Warfare Center Aircraft Division Warminster Purchase Description and match Olive Green 106 (see 3.4.1.2). 3.3.2 Vest components. The vest components (pockets, flaps, liners, patches) shall be fabricated from aramid oxford cloth conforming to MIL-C-7219, Color

24、 106 Olive Green (see 3.4.1.2). 3.3.3 Stiffener. The stiffener shall be fabricated from nylon duck cloth conforming to MIL-C-3953, Color 106 Olive Green (see 3.4.1.2). 4 Licensed by Information Handling Services3.3.4 Webbinss. m 99999Ob 1995697 2bT 3.3.4.1 Survival vest sub-assembly webbinq. The web

25、bing used to fabricate the survival vest sub-assembly shall be fabricated from nylon conforming to MIL-T-5038, Type IV, Class II, 2 inch wide as specified in drawing 3241AS302. 3.3.4.2 Securins belt assembly webbinqs. The webbings used to fabricate the securing belt assembly shall be fabricated from

26、 nylon conforming to MIL-W-4088, Type VIII, Class I, 1 23/32 inch wide and Type IV, Class 1, 3 inch wide as specified in drawing 3241AS303. 3.3.4.3 Torso harness assembly webbinas. The webbings used to fabricate the torso harness assembly shall be fabricated from nylon conforming to MIL-W-4088, Type

27、 XIII, Class I, 1 23/32 inch wide and from elastic conforming to MIL-W-5664, Type I, Class I, 1 1/2 inch wide as specified in drawing 3241AS304. 3.3.4.4 Flashlisht strap assembly webbinq. The webbing used to fabricate the flashlight strap assembly shall be fabricated from elastic conforming to MIL-W

28、-5664, Type I, Class III, 1 1/2 inch wide as specified in drawing 3241AS305. 3.3.4.5 HEED pocket assembly webbinq. The webbing used to fabricate the HEED pocket assembly shall be fabricated from elastic conforming to MIL-W-54, Type I, Class III, 1 inch wide as specified in drawing 3241AS307. 3.3.4.6

29、 AN/PRC radio pocket assembly webbinq. The webbing used to fabricate the AN/PRC radio pocket assembly shall be fabricated from elastic conforming to MIL-W-5664, Type I, Class III, 2 inch wide as specified in drawing 3241AS315. 3.3.5 TaDes. 3.3.5.1 Tape. The tape used to fabricate the survival vest a

30、ssembly shall be fabricated from nylon conforming to MIL-T-5038, Type III, Class II, 1 inch wide as specified by the applicable drawings in 2.1.2. 3.3.5.2 Seam tape. The seam tape used to fabricate the survival vest assembly shall be fabricated from nylon conforming to MIL-T-5038, Type III, Class II

31、, 1 inch wide as specified by the applicable drawings in 2.1.2. 3.3.5.3 Hook tapes. The hook tapes used to fabricate the survival vest assembly shall be fabricated from nylon conforming to MIL-F-21840, Type II, Class I, 1, 1 1/2 and 2 inch wide as specified by the applicable drawings in 2.1.2. 3.3.5

32、.4 Pile tapes. The pile tapes used to fabricate the survival vest assembly shall be fabricated from nylon conforming 5 Licensed by Information Handling ServicesMIL-V-29bOL m 9999906 L99569B LTb MIL-V-29601(AS) to MIL-F-21840, Type II, Class I, 1, 1 1/2, 2, and 4 inch wide as specified by the applica

33、ble drawings in 2.1.2. 3.3.6 Snap fasteners. 3.3.6.1 Eyelets. The eyelets used to fabricate the survival vest assembly shall be in accordance with MS27983-4 and MS27980-8B as specified by the applicable drawings in 2.1.2. 3.3.6.2 Studs. The studs used to fabricate the survival vest assembly shall be

34、 in accordance with MS27983-3 and MS27980- 7B as specified by the applicable drawings in 2.1.2 3.3.6.3 Sockets. The sockets used to fabricate the survival vest assembly shall be in accordance with MS27983-2 and MS27980-6B as specified by the applicable drawings in 2.1.2. 3.3.6.4 Buttons. The buttons

35、 used to fabricate the survival vest assembly shall be in accordance with MS27983-1 and MS27980-1B as specified by the applicable drawings in 2.1.2. 3.3.7 Slide fasteners. 3.3.7.1 Survival vest sub-assembly slide fastener. The slide fastener used to fabricate the survival vest sub-assembly shall be

36、in accordance with V-F-106 as specified in drawing 3241195302. 3.3.8 Slide Loops. The slide loops used to fabricate the survival vest sub-assembly shall be in accordance with MS51940-9S as specified in drawing 3241AS302. 3.3.9 D-rinss. 3.3.9.1 Survival vest sub-assembly D-rinqs. The D-rings used to

37、fabricate the survival vest sub-assembly shall be in accordance with MIL-R-3390, Class 2, as specified in drawing 3241AS302. 3.3.9.2 Torso harness assembly qated D-rinq. The gated D- ring used to fabricate the torso harness assembly shall be in accordance with drawing 823AS100, as specified in drawi

38、ng 3241AS304. 3.3.10 Grommets. The grommets used to fabricate the survival vest assembly shall be in accordance with MS20230B20 as specified by the applicable drawings in 2.1.2. 3.3.11 Trianqle parachute Link. The triangle parachute link used to fabricae the torso harness assembly shall be in accord

39、ance with MS22020-1 as specified in drawing 3241AS304. Licensed by Information Handling Services3.3.12 Parachute snap. The parachute snap used to fabricate the torso harness assembly shall be in accordance with MS22018 as specified in drawing 3241AS304. 3.3.13 Knife sheath. The knife sheath shall co

40、nform to MIL-K-8662, except that it shall not contain the sharpening stone, sharpening stone pocket, nylon laces, lace holes and slots for insertion of belt as specified in drawing 3241AS311. 3.4 Desiqn and construction. Unless otherwise specified, the design and construction of the vests shall conf

41、orm to the drawings listed in 2.1.2 of this specification. 3.4.1 Cut edses. The cut edges of the nylon webbings and tapes, except for the hook and pile fastener tapes, shall be seared, prior to the fabrication of the vests, to prevent fraying. No sharp edges shall be formed. The cut edges of the nyl

42、on duck cloth, except those that are completely covered by nylon binding tape, hook and pile fastener tapes, or are completely encased by the seam construction, shall be overedged stitched (serged). 3.4.1.1 Patterns. Standard patterns will be furnished by the Government to the contractor for use in

43、cutting working patterns (see 6.6). The working patterns shall be identica.1 to the Government patterns. Neither the Government patterns nor the working patterns shall be altered in any way. Seams shall be in accordance with seam allowances specified in 3.4. 3.4.1.2 Component parts. The component pa

44、rts shall be cut from the material specified, in accordance with the pattern parts in Table I. 3.4.2 Seams and stitching. All the seams used in the fabrication of the vests shall conform to the applicable drawings. Except for the serging (overedge) and zig-zag stitching, the stitching in the vest sh

45、all be accomplished with Stitch Type 301. The overedge stitching shall be accomplished with Stitch Type 502, 503, 504, or 505, and the zig-zag stitching shall be accomplished with Stitch Type 304. The width of the overedge and zig-zag stitching shall be approximately 1/4 inch. The thread and stitchi

46、ng used in fabrication shall conform to applicable drawing requirements. All the seam edges shall be properly forced out and shall not contain any folds. No seams shall be twisted, puckered, or pleated and no part of the vest shall be caught in an unrelated operation or seam. All the thread ends sha

47、ll be trimmed to a length of 1/4 to 3/8 inch and except for the webbing, cord, and tape, excluding the binding tape, no raw or cut edge shall be visible on the exterior of the vest. The cut edges of the binding tape shall be turned under. 3.4.2.1 Sewinq. Each row of stitching shall be straight and p

48、arallel to seam edge. The straightness of the stitching, in any row, shall be maintained within a tolerance of plus or minus 7 Licensed by Information Handling ServicesMIL-V-2960L 1/32 inch. The ends of the stitching that are not caught in other seams or stitching shall be securely backstitched, by

49、overlapping on themselves, for at least 1/2 inch. Thread breaks, skips, and run-Offs shall be over-stitched not less than one inch. The thread tension shall be maintained so that there shall not be any loose or tight stitching and the lock shall be embedded in the materials sewn together. 3.4.2.2 Bartackinq. Unless otherwise specified, bartackings shall conform to applicable drawing requirements. 3.5 Identification labels. Unless otherwise specified, identification labels shall conform to the requirements of Dwg 3214AS317. 3.5.1 Serial numbers. The vests shall be identified by indiv