NAVY MIL-R-46560 A (1)-1986 REMOVER AIRCRAFT CANOPY M3A1 METAL PARTS ASSEMBLY《 M3A1飞机座舱盖金属装配件清洗剂》.pdf

《NAVY MIL-R-46560 A (1)-1986 REMOVER AIRCRAFT CANOPY M3A1 METAL PARTS ASSEMBLY《 M3A1飞机座舱盖金属装配件清洗剂》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-R-46560 A (1)-1986 REMOVER AIRCRAFT CANOPY M3A1 METAL PARTS ASSEMBLY《 M3A1飞机座舱盖金属装配件清洗剂》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-R-465bOA (1) 13 7779706 0332740 2 K-e G MIL-R-46560A(OS) AMENDMENT 1 15 JULY 1986 MILITARY SPECIFICATION REMOVER, AIRCRAFT CANOPY, M3A1 METAL PARTS ASSEMBLY This amendment forms a part of Military Specification MIL-R-46560A(MU), dated 15 April 1965, and is approved for use within the Naval Sea S

2、ystems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1 Delete MIL-STD-639 Surface Roughness Values Preferred for Army Ordnance Materi al I PAGE 2 Add: “2.2 Other publications. The following document forms a part of th

3、is specification to the extent specified herein. Unless otherwise specified, the issues of the document which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. specified, the issues of documents not listed in the DODISS shall be the issue of the nongover

4、nment documents which is current on the date of the sol i ci tat i on. Unless otherwise ANS I 646.1-78 Surface Texture (Surface Roughness, Waviness and Lay) Beneficial comments (recommendations, additions, deletions) and any . pertinent data which may be of use in improving this document should be a

5、ddressed to: Standardization Branch (5241), Indian Head, MD 20640-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of the specification or by letter. Commanding Officer, Naval Ordnance Station, THIS DOCUMENT CONTAINS -2 PAGES. AMSC N

6、/A FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. c Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IIL-R-46560A (1) 13 I 7779906 0312941 4 = MIL- R- 46560A (OS) AMENDMENT 1 I 15 JULY 1986 (Application for

7、copies should be addressed to the American National (Nongovernment standards and other pub1 ications are normally available Standards Institute (ANSI), 1430 Broadway, NY 10018. ) from the organization which prepares or which distributes the documents. These documents also may be available in or thro

8、ugh libraries or other informational services, )I PAGE 5 4.3.2 Delete the last four lines and substitute: standards prescribed in ANSI B46.1 shall be used as a basis of comparison for surface roughness determination. performing visual examination for such defects as burr and foreign matter. “The roughness comparison Four power (4X) magnification may be used in Preparing Activity: Project No. 1377-N795 - Navy - OS 0U.S. QOVERNMENT PRINTINO OFFICE 1986 - 6W-038/44187 i 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-