NAVY MIL-R-24414 D-1991 REELS AND GUIDES HOSE FIREFIGHTING MANUALLY OPERATED《手动操作消防软管 卷轴和导向器》.pdf

《NAVY MIL-R-24414 D-1991 REELS AND GUIDES HOSE FIREFIGHTING MANUALLY OPERATED《手动操作消防软管 卷轴和导向器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-R-24414 D-1991 REELS AND GUIDES HOSE FIREFIGHTING MANUALLY OPERATED《手动操作消防软管 卷轴和导向器》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、IINCH-POUND MIL-R-24414D(SH) 19 November 1991 SUPERSEDING 30 March 1988 (See 6.10) MIL-R-24414C(SH) MILITARY SPECIFICATION REELS AND GUIDES, HOSE, FIREFIGHTING MANUALLY OPERATED This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use

2、by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers manually operated firefighting hose reels and hose guides for deck or bulkhead mounting on shipboard. 1.2 Classification. Equipment covered by this specification shall be one of the following

3、groups and types as specified (see 6.2): 1.2.1 Equipment Group. Group is identified by a letter symbol as shown i distribution is unlimited, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-24414D 42 m 999990b 0495247 3 M MIL-R-24414D(SH) Table

4、II. Equipment Twe “ .- “ “.“-.“I “.- Shipboard Machinery, Equipment and Systems, Requirements for. - Lumber and Plywood, Fire Retardant Treated. - Paint Coating Systems, Fuel and Salt Water Ballast - Insulation Tape, Electrical, Plastic, Pressure- - Paint, Epoxy-Polyamide, General Specification for.

5、 Tanks, (Metric) Sensitive. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-24414D 42 M 9999906 0495248 S m MIL-R-24414D(SH) STANDARDS FEDERAL FED-STD-H28 - Screw-Thread Standards for Federal Services. FED-STD-595 - Colors Used in Governemnt

6、Procurement. MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-108 - Definitions of and Basic Requirements for Enclosures MIL-STD-129 - Marking for Shipment and Storage, MIL-STD-130 - Identification Marking of U.S. Military Property. .- (Unless otherwise indicated, copi

7、es of federal and military.specifications, Attributes, for Electric and Electronic Equipment. standards, and handbooks are available from the Standardization Documents Order Desk, BLDG. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) f

8、orm a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues

9、 of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) A 108 - Standard Specification for Steel Bars, Carbon, Cold A 167 - Standard Specification for Stainless and Heat-Resisting Finished, Standard Quality. (DoD adopted) Chromium-Nickel Steel Plate,

10、Sheet, and Strip. (DoD adopted) A 229 - Standard Specification for Steel Wire, Oil-Tempered for Mechanical Springs. (DoD adopted) A 269 - Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service. (DoD adopted) A 276 - Standard Specification for Stainless a

11、nd Heat-Resisting Steel Bars and Shapes. A 312 - Standard Specification for Seamless and Welded Austenitic Stainless Steel Pipes. (DoD adopted) A 336 - Standard Specification for Steel Forgings, Alloy, for Pressure and High-Temperature Parts. A 366 - Standard Specification for Steel, Sheet, Carbon,

12、Cold- Rolled, Commercial Quality. (DoD adopted) MIL-P-24441/1 - Paint, Epoxy-Polyamide, Green Primer, Formula 150, MIL-B-24480 - Bronze, Nickel.-Aluminum (UNS No. C95800) Castings MIL-H-24580 - Hose Assemblies, Synthetic Rubber, Noncollapsible, MIL-N-25027 - Nut, Self-Locking, 250“F, 450“F, and 800F

13、. Type I. for Seawater Service. Fire Fighting. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-24414D 42 I 999990b 0495249 7 M MIL-R-24414D(SH) A 569 B 16 B 26 B 62 B 209 B 211 B 221 D 3951 - Standard Specification for Steel, Carbon (0.15 Max

14、imum, Percent), Hot-Rolled Sheet and Strip Commercial Quality, (DoD adopted) - Standard Specification for Free-Cutting Brass Rod, Bar, and Shapes for Use in Screw Machines. (Don adopted) - Standard Specification for Aluminum-Alloy Sand Castings, (DoD adopted) - Standard Specification for Composition

15、 Bronze or Ounce Metal Castings. (DoD adopted) - Standard Specification for Aluminum Alloy Sheet and Plate - Standard Specification for Aluminum and Aluminum-Alloy - Standard Specification for Aluminum Alloy Extruded Bars, - Standard Practice for Commercial Packaging. Bar, Rod, and Wire. (DoD adopte

16、d) Rods, Shapes and Tubes (DoD adopted) (DoD adopted) (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) B16.5 - Pipe Flanges and Flanged Fittings. (DoD adopted) (Appli

17、cation for copies should be addressed to the American National Standards Institute, 1430 Broadway, New York, NY 10018.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or

18、 through libraries or other informational services,) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence, Nothing in this document, however, supersedes applicable laws and regulations unless

19、 a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.4) in accordance with 4.3. 3.2 Materials. Unless otherwise specified (see 6.2), hose reels and guides shall be constructed of materials

20、 shown in Table I. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-“_ G roup A A and B B TABLE III. Material. Subassembly Frame Swing joint and axle Fluid path Reel drum Fasteners Al 1 Material specification ASTM A 366 ASTM B 211 ASTM B 209 ASTM B

21、221 ASTM B 62 ASTM A 276 ASTM A 269 MIL-B-24480 ASTM A 269 ASTM A 336 ASTM A 108 ASTM A 229 ASTM B 16 ASTM B 26 ASTM B 209 FF- S - 85 ASTM A 167 ASTM A 569 ASTM A 312 ASTM A 108 Material “_“ “ Aluminum bars Aluminum forgings Aluminum Sheet parts missing or improperly assembled. Materials defective o

22、r not as specified; evidence of cracks, deep pits, blowholes, shrinkage defects or foreign inclusions. Bearings defective or type II not protected from the weather. Reel not double supported. Hose does not meet drum in smooth tangent as specified. Device for clamping the nozzle to the reel missing o

23、r defective. Reel inlet connection not the required size or flange not smoothly finished. Hub discharge adapter missing, not securely mounted, or not as specified; threads stripped, torn, crossed shrunken (not concentric) not perfect full threads, or thread type and size not as specified. Bolt hole

24、diameter or spacing or inlet flange not as specified, or thickness of flange less than required. Width of drum not within the specified tolerance. Dissimilar metals that come in contact with each other not coated as required, or aluminum parts not coated as required. looseness, amount of rim pull re

25、quired to rotate reel exceeds the specified maximum (see 3.3). lubrication. Reel wobbles, sticks, binds, or evidences excessive Both ends of drum shafts not furnished with means of Rims of drum discs not rolled or not smooth surface. Complete fluid handling section of reel not removable Hose guide r

26、ollers bind. Hose guide rollers not self lubricated. without disassembly of the drum or reel sides. .-_ 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE VI, Classification of defects. (Continued) r “- “I-.-.“I “.“ Categories Defects -1“- ,- “

27、.“.“.-.“ Minor: 201 Mounting dimensions (bolt hole diameter or spacing) not 202 Diameter of reel exceeds the maximum permissible. as specified. 203 Overall height exceeds the maximum permissible, 204 Overall width exceeds the maximum permissible. 205 Horizontal or vertical location inlet flange not

28、within 206 Weight of reel exceeds the maximum allowable. 207 Marking, manufacturers name or trademark missing, 208 Means of lubrication not easily accessible. 209 Painted wrong color. the specified tolerance, illegible, incorrect or not as specified. 4.5.3 Sampling for quality conformance inspection

29、, Reel samples shall be selected at random from each lot in accordance with inspection level II of MIL-STD-105. TABLE VII. Sampling for clualitv conformance inspection. “ _. Sample Size I Major Minor Lot Size Characteristic Characteristic 2 to 8 9 to 50 51 to 90 91 to 150 151 to 280 281 to 500 501 t

30、o 1200 Al 1 8 8 12 19 21 27 5 5 7 11 13 16 19 -. - 4.6 Examination. Sample reels selected as specified in 4.5.2 shall be examined to determine conformance to the requirements of this specification not involving tests. Examination shall be conducted as specified in Table VII. 12 Provided by IHSNot fo

31、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-24414D 42 9999706 0495258 8 W MIL-R-24414D(SH) 4.7 Tests. 4.7.1 Operating test. reel unoressurized. Assembled reels selected as specified in 4.5.2 shall be loaded with hose and operated by hand to test all functions,

32、fits, clearances and adjustment (see 3.15). The holding brake operation shall applied sucessfully not less than three applications. 4.7.2 Pressure tests. 4.7.2.1 Hvdrostatic test. Prior to installation of hose, each reel shall be hydrostatically proof-tested to 400 psi. The pressure shall be held fo

33、r 5 minutes during which time there shall be no leakage or other signs of weakness (see 3.3.1). 4.7.2.2 Collapse pressure test. Each reel shall have hose or hoses, identical to the hose to be used in service (see 3.2.2), attached and wound on the reel. The reels and hose shall be pressurized with wa

34、ter to 240 psi. The pressure shall be held for 5 minutes. The pressure shall then be reduced to O psi and the hose shall be unwound from the reel. The drum shall show no evidence of collapse due to the growth or shrinkage of hose under pressure. Other reel parts shall show no evidence of damage or d

35、istortion due to this test. 4.7.3 Operating test, reel Dressurized. Upon completion of the collapse test (see 4.7.2.2), the reel and hose shall be repressurized as specified in 4.7.2.2 to 175 psi and the hose shall be reeled on and off the reel while under pressure. The reel shall operate smo;tbly w

36、ith no bending, wobbling or binding during this test. 4.7.4 Spravtightness test. The type II reel shall be subjected to the spraytight enclosure test in accordance with MIL-STD-108. 4.7.5 Shock test. The high impact (H.1.) shock tests shall be grade A, class I, type A in accordance with MIL-S-901. T

37、he reel shall be completely assembled (including hose), and shall be mounted on the shock machine in a manner simulating a typical shipboard bulkhead installation. The number of blows shall be as specified in MIL-S-901. Hose used for the H.I. shock test of reels need only be the same size, weight an

38、d length as hose to be used in service. The reel and hose shall not be pressurized nor filled with water for this test. 4.7.5.1 Examination after shock tests. The equipment shall be carefully examined to determine the extent of any damage to the mechanical parts after completion of the shock test. E

39、xamination of the reels shall determine the following: (a) The hose shall be unreeled and then replaced on the reel not less than five times. Any undue noise or difficulty in operation shall be investigated and the cause determined. outlet connection) shall be hydrostatically tested to 400 psi. Pres

40、sure shall be held for 5 minutes. There shall be no leakage during the hydrostatic test. (b) The fluid handling sections of the reel (between the inlet and 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(c) The reels shall be disassembled followi

41、ng the examination after shock tests specified and examined thoroughly for damage. The effects of the shock tests and subsequent check tests on the structure shall be carefully observed and determined. 4.7.5.2 Failure to Dass shock test. The hose reel shall have failed the shock tests in the event o

42、f the following: (a) Breakage of any parts including mounting bolts. (b) Appreciable distortion or dislocation of any parts, including (c) Excessive unbalance determined as specified in 4.7.5.1. (d) Failure to pass the hydrostatic test. mounting feet and bearings. 4.7.6 Possible test failures. Possi

43、ble test failures of the reels shall be determined as follows: (a) Operating test - failure of reel to contain the specified length of hose, evidence of bending, wobbling, or binding when loaded reel is rotated. the indicated hydrostatic pressure is applied to the fluid handling section of the reel.

44、 the ,specified fluid handling section is applied to the fluid-carrying portion of the reel, (b) Hydrostatic test - evidence of leakage or binding of the seals when (c) Water - evidence of leakage or binding of the seals when 4.8 Insoection of Dackaginq. Sample packages and packs, and the inspection

45、 of the preservation, packing and marking for shipment stowage and storage shall be in accordance with the requirements of section 5 and the documents specified therein. 5. PACKAGING (The packaging requirements specified herein apply only for direct Government acquisition, For the extent of applicab

46、ility of the packaging requirements of referenced documents listed in section 2, see 6.5.) 5.1 Preservation. Preservation shall be level A or commercial, as specified (see 6.2). 5.1.1 Level A. Reels or hose guides shall be individually unit protected in accordance with MIL-P-I16 method III. All open

47、ings shall be sealed with blank flanges, threaded plugs or caps or pressure sensitive waterproof tape. Tape shall conform to PPP-T-60 type IV, color optional. 5.1.2 Commercial. Reels or hose guides shall be individually unit protected in accordance with ASTM D 3951. 5.2 Packing. Packing shall be lev

48、el A, B, C, or commercial, as specified (see 6.2). 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IIL-R-24414D 42 W 9999906 0495260 b W MIL-R-24414D(SH) 5.2.1 Level A, Reels or hose guides preserved as specified in 5.1 shall be individually packe

49、d in overseas type containers conforming to PPP-B-585 class 3, PPP-B-601 overseas type, or PPP-B-621 class 2, with container selection at the option of the contractor. Containers exceeding a gross weight of 200 pounds (90.72 kilograms (kg) shall be modified by the addition of 3 by 4 inch (7.62 by 10.16 centimeter (cm) wood skids placed flat. The reels shall be shrouded within the containers with barrier m