NAVY MIL-PRF-8565 17 A-2012 BATTERY STORAGE AIRCRAFT MAINTENANCE-FREE 24-VOLT 1 3-AMPERE-HOUR.pdf

《NAVY MIL-PRF-8565 17 A-2012 BATTERY STORAGE AIRCRAFT MAINTENANCE-FREE 24-VOLT 1 3-AMPERE-HOUR.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-PRF-8565 17 A-2012 BATTERY STORAGE AIRCRAFT MAINTENANCE-FREE 24-VOLT 1 3-AMPERE-HOUR.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 6140 PERFORMANCE SPECIFICATION SHEET BATTERY, STORAGE, AIRCRAFT, MAINTENANCE-FREE, 24-VOLT, 1/3-AMPERE-HOUR This specification is approved for use by the Naval Air Systems Command and is available for use by all Departments and Agencies of the Department of Defense. The requirements fo

2、r acquiring the product described herein shall consist of this specification sheet and MIL-PRF-8565. REQUIREMENTS 1. Part or identifying number. The part or identifying number (PIN) of the battery covered by this specification sheet shall be D8565/17-1. 2. Dimensions and weight. The dimensions and t

3、he configuration of the battery container shall be as shown on figure 1 of this specification sheet. The weight of the battery shall be not greater than 3.5 pounds (1.59 kg). See 3.8.3 and 4.5.3 of MIL-PRF-8565. 3. Capacity. The rated capacity of the battery shall be 1/3-ampere-hours, based on its a

4、bility to conform to the life test final discharge. The life test final discharge is a 1-hour discharge at 24 C ambient temperature with a 0.33-ampere load (1C-rate) to a cutoff voltage of 19 volts (0.33 Amp/1.0 hr/24 C/19.0V). See 3.8.6, 4.5.7 and 6.15.2 of MIL-PRF-8565. 4. Application. The battery

5、 shall not be designed for engine starting applications. 5. Mounting. For installation in the aircraft, the battery shall be mounted as shown on figure 3 of MIL-PRF-8565. INCH-POUND MIL-PRF-8565/17A(AS) 23 May 2012 SUPERSEDING MIL-PRF-8565/17(AS) 9 February 2007 MS17334P 22 April 1982 (See 6.9) Prov

6、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8565/17A(AS) 2 6. Service life. The batterys service life (useful life) in the aircraft shall be not less than 3 years (36 months). The battery shall require no scheduled maintenance during its serv

7、ice life (see 3.8.9 and 6.15.10 of MIL-PRF-8565; see 4.5.10 and 6.11.7.2 as specified herein). 7. Qualification inspection and conformance inspection. Table I of this specification sheet lists the required inspections. 8. MIL-PRF-8565 variance. The battery shall comply with MIL-PRF-8565 except as fo

8、llows. 8.1 The following paragraphs are not applicable: 3.5.4 Venting. 3.5.10 Heaters. 3.6.5 Marking for batteries with heaters. 3.8.4 Dielectric strength and insulation resistance. 3.8.5 Vent tubes. 3.8.7 Constant voltage discharge. 3.8.8 Strength of receptacle. 3.8.12 Battery gas emission. 3.8.14

9、Impact resistance (nonmetallic battery container only). 3.8.16 Output performance. 3.8.17 Cold and hot temperature charge. 4.5.4 Dielectric strength and insulation resistance test. 4.5.5 Strength of vent tubes test. 4.5.8 Constant voltage discharge. 4.5.9 Strength of receptacle test. 4.5.18 Battery

10、gas emission test. 4.5.24 Impact resistance test (nonmetallic battery container). 4.5.28 Output performance test. 4.5.29 Cold and hot temperature charge test. 4.5.30 Wormgear retaining pin hardness. 8.2 Modify the following paragraphs: 3.5.3 Battery container and cover. In the second sentence, delet

11、e “hold-downs, vent tubes”. 3.5.5 Receptacles. Delete the second sentence and substitute: “The battery shall contain an electrical connector dimensionally equal to MS3102R-14S-7S. The connector shall be installed on the battery in the location shown on figure 1 of MIL-PRF-8565/17(AS), and the key of

12、 the connector shall be in the 12 oclock position. The connector socket pin allocations shall be in accordance with the following: “a. Socket A shall be battery negative (-) for battery charging and discharging. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

13、m IHS-,-,-MIL-PRF-8565/17A(AS) 3 “b. Socket B shall be +28 VDC input for battery charging and positive (+) for battery discharge output. “c. Socket C shall not be used (spare) in this application. The battery shall be designed so that no internal components of the battery make mechanical or electric

14、al contact with socket C.” 3.5.7 Electrolyte leakage. Delete “except when tested in accordance with 4.5.18”. 3.6.3 Identification marking. In the third sentence, delete “figure 1 herein” and substitute “figure 2 of MIL-PRF-8565/17(AS)”. 3.6.4 Battery caution marking. In the first sentence, delete “f

15、igure 2 herein” and substitute “figure 3 of MIL-PRF-8565/17(AS)”. 3.7 General requirements. Delete the text of 3.7.e and substitute: “Electrolyte leakage or spilling of electrolyte at any time during the test. Corrosive or liquid discharge shall not occur during testing to this specification. Produc

16、ts of cell venting that are discharged shall be non-toxic.” 8.3 Add the following paragraph to MIL-PRF-8565: “3.8.18 Pulsed high rate discharge. The battery potential shall be not less than 10.6 volts throughout each of the three discharges after being tested in accordance with 4.5.31, as specified

17、in MIL-PRF-8565/17(AS).” VERIFICATION 1. MIL-PRF-8565 variance. The battery shall comply with MIL-PRF-8565 except as follows: 1.1 Modify the following MIL-PRF-8565 paragraphs: 4.3.4 Group A inspection. Delete the last sentence. 4.4.2 Constant potential charging method. In the first sentence, delete

18、“28.25 0.25 volts for 2.0 0.1 hours” and substitute “28.5 0.5 volts for 5.0 0.1 hours”. 4.4.3 Constant current charging method. Delete “C/10 (3 percent)” and substitute “0.075 amperes”. 4.5.6 Electrical test preparation. In the first sentence, delete “18.0 volts” and substitute “19.0 volts”. Provide

19、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8565/17A(AS) 4 4.5.7 Capacity discharge. In the second sentence, delete “18.0 volts” and substitute “19.0 volts”. 4.5.10 Cycling test. Delete the text of 4.5.10 and substitute: “Constant potential char

20、ge the battery in accordance with 4.4.2, as modified by MIL-PRF-8565/17(AS), at room temperature (see 4.4.1 of MIL-PRF-8565). Subject the battery to 100 cycles of discharge and charge under the ambient conditions of 4.4.1 of MIL-PRF-8565. Each cycle shall consist of a 1.0-hour, 1.0C-rate discharge,

21、followed by a 5.0-hour constant potential charge of 28.5 volts, followed by a 1-hour rest period. “ 4.5.11 Capacity discharge at 49 C (120 F). In the third sentence, delete “18.0 volts” and substitute “19.0 volts”. 4.5.12 Charge and discharge test at low temperature. In steps c and f (second sentenc

22、e), Delete “18.0 volts” and substitute “19.0 volts”. 4.5.13 Discharge while inverted. In step c, delete “14.0 volts” and substitute “15.0 volts”. 4.5.14 Altitude test. In steps c through h, delete the text and substitute: “c. Within 15 minutes after completing step 4.5.14b of MIL-PRF-8565, lower the

23、 chamber temperature to 29 C (-20 F) and lower pressure inside chamber to simulate ambient pressure at temperature environment. “d. Discharge the battery at the 6.5C-rate for 3 minutes or to a cutoff voltage of 15.0 volts, whichever comes first. Examine the battery for the requirements of 3.8.10 of

24、MIL-PRF-8565. “e. Constant potential charge the battery in accordance with 4.4.2, as modified by MIL-PRF-8565/17(AS) for 2 hours. “f. Open-circuit the battery and, within 5 minutes, return the chamber to ground ambient air pressure (see 4.4.1 of MIL-PRF-8565). “g. Discharge the battery at the 6.5C-r

25、ate for 3 minutes or to a cutoff voltage of 15.0 volts, whichever comes first. Examine the battery for the requirements of 3.8.10 of MIL-PRF-8565. “h. Examine the battery for the requirements of 3.7, as modified by MIL-PRF-8565/17(AS) and 3.5.9 of MIL-PRF-8565.” 4.5.15 Shock test (basic design). In

26、step f, delete the sentence and substitute: “After the fifteenth impact, discharge the battery at the 6.5C-rate for 3 minutes or to a cutoff voltage of 15.0 volts, whichever occurs first.” Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8565/

27、17A(AS) 5 4.5.16 Temperature shock test. In step b, delete the second sentence. In step d, delete the second sentence. In step f, delete the second sentence. In step j, delete the text and substitute “discharge the battery at the 6.5C-rate for 3 minutes or to a cutoff voltage of 15.0 volts, whicheve

28、r comes first”. 4.5.17 Temperature rise and float test. In step e, delete “18.0 volts” and substitute “19.0 volts”. 4.5.19 Vibration test. In step c, insert the following after the first sentence: “Vibration isolators shall not be used”. In step g, delete the text and substitute: “Discharge the batt

29、ery at the 6.5C-rate for 3 minutes or to a cutoff voltage of 15.0 volts, whichever occurs first.” 4.5.20 Humidity test. In step i, delete the text and substitute: “Discharge the battery at the 6.5C-rate for 3 minutes or to a cutoff voltage of 15.0 volts, whichever occurs first.” 4.5.21 Salt fog test

30、. In step j, delete the text and substitute: “Discharge the battery at the 6.5C-rate for 3 minutes or to a cutoff voltage of 15.0 volts, whichever occurs first.” 4.5.22 Ground storage tests. In steps d and i, delete “18.0 volts” and substitute “19.0 volts”. 4.5.23 Physical integrity at high temperat

31、ure test. In step b, delete “18.0 volts” and substitute “19.0 volts”. In step e, delete the last sentence. In step k, delete “18.0 volts” and substitute “19.0 volts”. 4.5.25 Shock test (crash safety). In step f, delete the last sentence and substitute: “Discharge the battery at the 6.5C-rate for 3 m

32、inutes or to a cutoff voltage of 15.0 volts, whichever occurs first.” 4.5.26 Shelf life test. After the third sentence, delete the text and substitute: “Constant potential charge the battery in accordance with 4.4.2, as modified by MIL-PRF-8565/17(AS). Stabilize the battery at room temperature (see

33、4.4.1 of MIL-PRF-8565). Discharge the battery at the C-rate to 19.0 volts. Constant potential charge the battery in accordance with 4.4.2, as modified by MIL-PRF-8565/17(AS). Subject the battery to the cycling test of 4.5.10, as modified by MIL-PRF-8565/17(AS). Examine the battery for the requiremen

34、ts of 3.8.9 and 3.8.13.2, both of MIL-PRF-8565.” 4.5.27 Deep discharge recovery test. In step b, delete “1.0 ohms” and substitute “5.0 ohms”. In step d, delete “C/10 (3 percent)” and substitute “0.075 ampere”. In step f, delete “C/10 ( 3 percent)” and substitute “0.075 ampere”. 1.2 MIL-PRF-8565, par

35、agraph 4.5.31 delete and substitute: “4.5.31 Pulsed high rate discharge test. Constant potential charge the battery in accordance with 4.4.2, as modified by MIL-PRF-8565/17(AS). Discharge the battery at 9.12 amperes for Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

36、ense from IHS-,-,-MIL-PRF-8565/17A(AS) 6 20 seconds, followed by a 2-minute rest period. Repeat the discharge/rest period cycle two additional times. Examine the battery for compliance with 3.8.18, as specified in MIL-PRF-8565/17(AS).” 1.3 Add the following paragraph to MIL-PRF-8565: 4.5.32 Final ex

37、amination. Without dissecting the battery, examine it for the requirements of 3.7, as modified by MIL-PRF-8565/17(AS). NOTES 1. Modify the following paragraph. 6.9 Cross-reference. Insert the following after the first sentence: “This specification supersedes MS17334P(AS) in its entirety. PIN D8565/1

38、7-1 supersedes both PINs MS17334-1 and MS17334-2.” 2. Add the following paragraphs to MIL-PRF-8565. “6.11.7 Additional application information. The following information is provided for users of the D8565/17-1 battery. “6.11.7.1 Initial installation date. The initial installer should write the date

39、the battery is first installed in an aircraft (date first placed in service) in the space provided on the batterys identification marking (see figure 2 of MIL-PRF-8565/17(AS). “6.11.7.2 Service life and removal from aircraft. The batterys service life (useful life) in the aircraft is limited to 36 m

40、onths. The battery should be removed from aircraft service 36 months after the date it was first installed in an aircraft (see requirement 6 of MIL-PRF-8565/17(AS). “6.11.8 Environmental characteristics. Battery performance should not be adversely affected when operating in a sand and/or dust enviro

41、nment. Battery materials should not support fungus growth. The battery should operate safely in an atmosphere containing ignitable or explosive fumes.” Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8565/17A(AS) 7 TABLE I: Delete and substit

42、ute: TABLE I. Qualification inspection and conformance inspection. Test number Examinations and tests Qualification inspection Conformance inspection Sample number Requirement paragraph 1/Test paragraph 1/ Group A sample 1 100% Group B sample number 1 2 3 1 2 1 INCOMING INSPECTION X X X 3.8.1. (G) 4

43、.5.1 (G) X X 2 VISUAL AND MECHANICAL EXAMINATION 2/ X X X 2/ 3.5 2/ 3.6 , 3.8.2 (G), table II (G) 4.5.2 (G) X X X 3 DIMENSIONS AND WEIGHT X X X Reqmt 2 (N), 3.8.3 (G) 4.5.3 (G) X 3/ X 4 ELECTRICAL TEST PREPARATION X X X 4.5.6 (S) X X 5 CAPACITY DISCHARGE X X Reqmt 3 (N), 3.8.6 (G) 4.5.7 (S) X X X 6

44、CYCLING TEST X Reqmt 6 (N), 3.8.9 (G) 4.5.10 (S) X 7 CAPACITY DISCHARGE AT 49 C X 3.8.6 (G), reqmt (3) of table III (S) 4.5.11 (S) 8 CHARGE AND DISCHARGE TEST AT LOW TEMPERATURE X 3.8.6 (G), reqmt (2) of table III (S) 4.5.12 (S) X 9 DISCHARGE WHILE INVERTED X 3.5.9 (G), reqmt 5 of table III (S) 4.5.

45、13 (S) 10 ALTITUDE TEST X 3.5.9 (G), 3.7 (S), 3.8.10 (G) 4.5.14 (S) X 11 SHOCK TEST (BASIC DESIGN) X 3.7 (S), 3.8.10 (G) 4.5.15 (S) 12 TEMPERATURE SHOCK TEST X 3.7 (S), 3.8.10 (G) 4.5.16 (S) X 13 TEMPERATURE RISE AND FLOAT TEST X 3.7 (S), 3.8.11 (G), reqmt (1) of table III (S) 4.5.17 (S) X 14 VIBRAT

46、ION TEST X 3.7 (S), 3.8.10 (G) 4.5.19 (S) X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8565/17A(AS) 8 TABLE I. Qualification inspection and conformance inspection - Continued. Test Number Examinations and tests Qualification inspection C

47、onformance inspection Sample number Requirement paragraph 1/Test paragraph 1/ Group A sample 1 100% Group B sample number 1 2 3 1 2 15 HUMIDITY TEST X 3.7 (S), 3.8.10 (G) 4.5.20 (S) X 16 SALT FOG TEST X 3.7 (S), 3.8.10 (G) 4.5.21 (S) X 17 SHOCK TEST (CRASH SAFETY) X 3.8.10 (G), 3.8.15 (G) 4.5.25 (S)

48、 18 GROUND STORAGE TEST X 3.8.13.1 (G) 4.5.22 (S) 19 PHYSICAL INTEGRITY AT HIGH TEMPERATURE TEST X 3.7. (S), 3.8.10 (G), reqmt (1) of table III (S) 4.5.23 (S) 20 DEEP DISCHARGE RECOVERY TEST X 3.7 (S), 3.8.13.3 (G) 4.5.27 (S) 21 SHELF LIFE TEST X 3.8.9 (G), 3.8.13.2 (G) reqmt (1) of table III (S) 4.

49、5.26 (S) 22 PULSED HIGH RATE DISCHARGE TEST X 3.8.18 (N) 4.5.31 (N) X 23 FINAL EXAMINATION X X X 3.7 (S) 4.5.32 (S) X X 1/ The notations in parentheses specify the source of the paragraph or table. “(G)” means the paragraph is as shown in MIL-PRF-8565. “(S)” shows that the paragraph or table has been modified by this specification sheet. “(N)” indic