NAVY MIL-PRF-23586 F (2)-2002 SEALING COMPOUND (WITH ACCELERATOR) SILICONE RUBBER ELECTRICAL [Use In Lieu Of NAVY MIL-S-0023586 B]《电气用硅胶密封胶(含促进剂)》.pdf

《NAVY MIL-PRF-23586 F (2)-2002 SEALING COMPOUND (WITH ACCELERATOR) SILICONE RUBBER ELECTRICAL [Use In Lieu Of NAVY MIL-S-0023586 B]《电气用硅胶密封胶(含促进剂)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-PRF-23586 F (2)-2002 SEALING COMPOUND (WITH ACCELERATOR) SILICONE RUBBER ELECTRICAL [Use In Lieu Of NAVY MIL-S-0023586 B]《电气用硅胶密封胶(含促进剂)》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、PERFORMANCE SPECIFICATIONSEALING COMPOUND (WITH ACCELERATOR), SILICONE RUBBER, ELECTRICALThis amendment forms a part of MIL-PRF-235 86F, dated 30 December 1996, and isapproved for use by all Departments and Agencies of the Department of Defense.PAGE 1* 1.2.2, Class 4 : Delete “80 1C (175 2F)”.PAGE 2

2、2.2.1, under SPECIFICATIONS, FEDERAL, delete:“TT-E-751 - Ethyl Ace tate, TechnicalTT-I-735 - Isopropyl AlcoholTT-N-97 - Naphtha, Aromatic.”2.2.1, under SPECIFICATIONS, DEPARTMENT OF DEFENSE, delete:“MIL-C-38736 - Cleaning Compound, Solvent Mixtures, for Use in IntegralFuel Tanks.”PAGE 32.3, under AM

3、 ERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM), delete:“ASTM-D740 - Methyl Ethyl Ketone, Standard Specification for(DoD Adopted).”AMSC N/A 1 of 3 FSC 8030DISTRIBUTION STATEMENT A . Approved for public release; distribution is unlimited.NOT MEASUREMENTSENSITIVEMIL-PRF-23586FAMENDMENT 211 January_20

4、02SUPERSEDINGAMENDMENT 114 February 2000Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23586FAMENDMENT 22Add:“SOCIETY OF AUTOMOTIVE ENGINEERS (SAE)SAE-AMS3166 - Solvents, Cleaning, Cleaning Prior to Application of SealingCompounds.(Applicati

5、on for copies should be addressed to the Customer Service Department,Publications Group, SAE, 400 Commonwealth Drive, Warrendale, PA 15096.).”PAGE 7* 3.5: Add “e. Curing time and temperature.”PAGE 10* TABLE IV, title : Delete “ 1 /”.* TABLE IV, note 1 / : Delete “class 4 conformance specimens shall

6、be heat cured for 1 hourat 150 1C (302 2F).”4.5 , line 3 : Delete and substitute “in accordance with SAE-AMS3166. Immediately afterrinsing.”PAGE 11TABLE V : Delete in its entirety.* 4.6.2: Delete and substitute “Class 4 sealing compound shall be cured in accordance withthe manufacturers instructions

7、 (see 3.5). Heat-cured specimens shall cool to standard conditionsand be permitted to stand for 4 hours or more after reaching standard conditions before testing.”PAGE 17* 6.4, line 8 : Delete “Naval Air Systems Command, AIR-4.3.4, 1421 Jefferson DavisHighway, Arlington, VA 22243-5120; however, info

8、rmation pertaining to qualification ofproducts may be obtained from“The margins of this amendment are marked with an asterisk to indicate where changes fromthe previous amendment were made. This was done as a convenience only and the governmentassumes no liability whatsoever for any inaccuracies in

9、these notions. Bidders and contractorsare cautioned to evaluate the requirements of this document based on the entire contentirrespective of the marginal notations and relationship to the last previous amendment.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23586FAMENDMENT 23Custodians: Preparing activity:Army - MR Navy - ASNavy ASAir Force - 99 (Project 8030 - 0811)Review activities:Army - AV, CRNavy - EC, OSAir Force - 84Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-