NAVY MIL-PRF-23199 1 B-2010 PACKAGING PACKING AND MARKING (PP&M) REQUIREMENTS FOR INSTRUMENTATION AND CONTROL EQUIPMENT《测试设备和控制设备的包装 打包和标记要求》.pdf

《NAVY MIL-PRF-23199 1 B-2010 PACKAGING PACKING AND MARKING (PP&M) REQUIREMENTS FOR INSTRUMENTATION AND CONTROL EQUIPMENT《测试设备和控制设备的包装 打包和标记要求》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-PRF-23199 1 B-2010 PACKAGING PACKING AND MARKING (PP&M) REQUIREMENTS FOR INSTRUMENTATION AND CONTROL EQUIPMENT《测试设备和控制设备的包装 打包和标记要求》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Inch-Pound MIL-PRF-23199/1 (SH) Revision B 14 June 2010 Superseding MI L-PRF-23199/1 (SH) Revision A 28 February 2003 PERFORMANCE SPECIFICATION PACKAGING, PACKING AND MARKING (PP distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

2、,-,-MIL-PRF-23199/1 (SH) Revision B 14 June 2010 NSN National Stock Number OBRP On-Board Repair Parts OBS On-Board Spares PEM Plastic Encapsulated Microcircuit PP thus, any reference to these levels in contractual documents is not applicable. The entire specification should be assumed applicable unl

3、ess otherwise noted in contractual documents. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, or 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional informa

4、tion or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3, or 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specif

5、ications and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in that issue cited in the solicitation or contract. Unless otherwise specified, later issue

6、 of the specifications and standards may be used at the option of the Seller. STANDARDS MILITARY MIL-STD-129 Marking for Shipment and Storage MIL-STD-2041 Control of Detrimental Materials MIL-STD-2073-1 Standard Practice for Military Packaging SPECIFICATIONS MILITARY MIL-DTL-117 Bags Heat-Sealable M

7、IL-I-8835 Indicator, Humidity, Card, Chemically Impregnated MIL-DTL-17361 Circuit Breakers, Air, Electric, Insulated Housing, (Shipboard Use), General Specification for MIL-DTL-17587 Circuit Breakers, Low Voltage, Electric Power, Air, Open Frame, Removable Construction MIL-DTL-24466 Polyethylene Bag

8、s, Sheet, and Tubing, Green MIL-PRF-81705 Barrier Materials Flexible, Electrostatic-Free, Heat Sealable MIL-DTL-81997 Pouches, Cushioned, Flexible, Electrostatic-Free Reclosable, Transparent (Copies ?f these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/asslst.dap

9、s.dla.mJl or from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 40, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents. The following other Government documents form a Page 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

10、m IHS-,-,-MIL-PRF-23199/1 (SH) Revision B 14 June 2010 part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or contract. FEDERAL A-A-3129 Cushioning Material, Flexible Open Cell Plastic Film (For Packaging Applications) A-A-

11、3174 Plastic Sheet, Polyolefin A-A-59135 Packaging Material, Sheet DOT-CFR-049 Federal Motor Vehicle Safety Standards PPP-C-00795 Cushioning Material, Packaging (Flexible Closed Cell Plastic Film, For Long Distribution Cycles) PPP-C-1797 Cushioning Material, Resilient, Low Density, Unicellular, Poly

12、propylene Foam 2.3 Non-Government Publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. IPC ASSOCIATION CONNECTING ELECTRONICS INDUSTRIES IPC/JEDEC

13、Handling, Packing, Shipping and Use of Moisture/Reflow J-STD-033 Sensitive Surface Mount Devices (Applications for copies should be addressed to the Institute for Interconnecting and Packaging Electronic Circuits, 2215 Sanders Road, Northbrook, IL 60062-6135.) AMERICAN SOCIETY FOR TESTING AND MATERI

14、ALS (ASTM) ASTM F 392 Standard Test Method for Flex Durability of Flexible Barrier Materials ASTM F 1249 Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor ASTM D 3951 Standard Practice for Commercial Packaging ASTM D6251 Standa

15、rd Specification for Wood-Cleated Panelboard /06251M Boxes ASTM 07478 Standard Specification for Heavy Outy Sheathed Wood /07478M Crates (Copies of these documents are available from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or online at www.astm.org.) 3. PACKAGING,

16、 PACKING AND MARKING REQUIREMENTS 3.1 General Requirements 3.1 .1 Materials 3.1,1.1 “Loose fill“ cushioning: Use of “loose fill“ cushioning is prohibited. Page 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23199/1 (SH) Revision B 14 June

17、2010 3.1.1.2 Fiberboard Boxes: The gross weight of a fiberboard box, including contents, shall not exceed the manulacturers maximum gross weight described on the box. In no case shall the gross weight of a fiberboard box including contents exceed 200 pounds. Cleated panel boxes or palletized, skidde

18、d fiberboard boxes shall be used when the load is characterized by irregular shape not lending support to the container or by great density (e.g., large transformers). Boxes in accordance with ASTM 06251, Type lor Type II, Class 1 or Class 2, Style A are acceptable. 3.1.1.3 Wooden Boxes: Wooden boxe

19、s for gross shipments under 200 pounds do not require skids. Component shipments in wooden boxes exceeding 200 pounds shall have skids suitable for fork lifting. Wooden boxes shall be girth strapped using rust resistant steel banding around the box in not less than two places. For skids, the girth s

20、traps shall be applied to and immediately adjoining the inner edge of each skid. For skid-type base boxes, wooden blocking shall be affixed to the base to prevent fork-lifting of loads from the ends. The blocking shall not extend beyond the sheathing envelope, shall be permanently attached, and shal

21、l not interfere with sling handling of the load. Wooden boxes, including contents, shall not exceed 800 pounds. Reinforced wooden box sketches that include the blocking, bracing and anchoring arrangement shall be provided in the Sellers procedure. 3.1.1.4 Wooden Crates: Components exceeding 800 pou

22、nds shall be packed in skid based wooden crates per the construction requirements of ASTM D 7478/D 7478M using material per 3.1.1.5. Wooden blocking shall be affixed to the base to prevent fork-lifting of loads from the ends. The blocking shall not extend beyond the sheathing envelope, shall be perm

23、anently attached, and shall not interfere with sling handling of the load. Reinforced wooden crate sketches that include the blocking, bracing and anchoring arrangement shall be provided in the Sellers PP 3.2.6 for miscellaneous items; 3.2.7 for spare components, etc.). Packaging instructions provid

24、ed by the GPA take precedence over the requirements stated herein. Similar items shall be packaged as a lot provided that the lot size does not exceed the number of Page 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23199/1 (SH) Revision

25、 B 14 June 2010 parts required to modify one assembly. For example, if four identical screws are required to modify a given drawer and there are two drawers per ship, then the field change kit should allow four screws per bag. Spare items shall be packaged to allow for shipment separate from the ins

26、talled items. 3.2.10.2 Packing Items being furnished as part of a field change kit shall be packed in accordance with the applicable requirements specified herein, for the type of item being shipped (e.g., 3.2.2 for drawers, chassis; 3.2.6 for miscellaneous items; 3.2.7 for spare components, etc.).

27、If the GPA has contracted for the Seller to install the field change kit and long-term storage is not involved, all items (except for spare parts) may be over-packed in one or more wooden or fiberboard boxes per the applicable requirements herein. Alternate methods of over-packing will be considered

28、 and authorized by the GPA on a case by case basis. (For example, over packing PWAs in plastic cases or combining the entire unit packaged material in aluminum or wood shipping crates.) Spare parts shall be packed in a separate container in accordance with 3.2.7. 3.2.10.3 Marking Marking shall be in

29、 accordance with 3.3. 3.2.11 Heat Exchangers, Cold Plates these items are covered by 3.2.6.1. Prior to packaging, each item shall be purged free of water using clean, dry shop air. Subsequently, the inlet and outlet ports shall be capped with a suitable cap (of a commercial material that is not detr

30、imental to the part being capped and is not PVC) to preclude the entrance of moisture or foreign material. The caps/plugs shall be designed such that they cannot be inadvertently pushed into the piping ports. This requirement also applies to items that are being shipped installed in a cabinet, enclo

31、sure or panel. Appropriate cushioning material/support shall be provided to preclude damage, bending, deforming, or otherwise causing a dimensional change to the orientation of the inlet port, outlet port, piping and heat exchanger fins. This requirement also applies to items that are being shipped

32、installed in a cabinet, enclosure or panel. Desiccants and humidity cards are not required. A label shall be provided with each unit package that contains the following marking, or equivalent: CAUTION DO NOT REMOVE CAPS FROM THE PIPING INLET AND OUTLET PORTS EXCEPT FOR INSPECTION OR INSTALLATION. CA

33、PS MUST BE REMOVED PRIOR TO INSTALLATION. This label shall also be provided on the final pack for items installed in a cabinet, enclosure or panel. 3.3 Marking Requirements All markings must meet the requirements of MIL-STD-129. 3.3.1 Unit Pack Marking Page 18 Provided by IHSNot for ResaleNo reprodu

34、ction or networking permitted without license from IHS-,-,-MIL-PRF-23199/1 (SH) Revision B 14 June 2010 3.3.1.1 Minimum Label Information. The following minimum information to be printed on the label shall include: Bar Code Marking National Stock Number Description Drawing/Piece Number, MIL Designat

35、ion or Catalog Number Quantity and Unit of Measure Purchase Order Number Supplier Name or CAGE Code Equipment Line Item Number (ELlN) when supplied by the GPA In addition to the above markings, all labels for ESD sensitive components shall be marked with the standard ESD symbol per MIL-STD-129 and t

36、he statement “DO NOT OPEN EXCEPT AT APPROVED FIELD FORCE PROTECTIVE WORK STATION“. The minimum of the symbol shall be one third of an inch measured vertically. The historical ESD symbol (three arrows in a circle) should no longer be used. 3.3.1.2 Shelf Life Marking. When the item being shipped has a

37、 finite shelf life (e.g., 60 months or less), insert the additional information: (This requirement applies to the end item and not to elastomers installed in components.) a. Type I Shelf Life Item b. Cure Date (Seller to insert cure date if an elastometer) c. Expires (Seller to insert shelf life exp

38、iration date) d. To be disposed of upon expiration NOTE: Elastomers with a shelf life between 5 and 19 years must be marked with a shelf life of 5 years. Elastomers with a shelf life of 20 years or greater must be marked “Cure Date_. Do not use 20 years beyond cure date.“ 3.3.2 Intermediate Packing

39、and Marking. Intermediate packing for field change kit material shall be in accordance with 3.2.10 and as specified in the field change ordering data. Individually packaged components may be over packed in a temporary shipping container for transportation to the destination. 3.3.3 Outer Container Ma

40、rking. Exterior markings shall contain only that information specified in 3.3.3.1-4, 6-10, 15 and 16 (Mandatory) and 3.3.3.5, 11-14 and 17 (as appropriate) below. Markings on exterior containers shall not reference any: (1) Project, (2) Equipment Specification, or (3) Number of Installed Components

41、3.3.3.1 Name and Address of Seller 3.3.3.2 Include the complete destination address as provided by GPA and note “For APA Stock“, “On-Board-Spares“, “Shipyard Installation Tools“, “Tender Load List“, or Tender Allowance List“ if applicable. Include hull number. The specific destination will be furnis

42、hed by the GPA prior to shipment. 3.3.3.3 Item description(s), including National Stock Numbers (NSN) with Bar Code marking. When shipments include components intended for both installation and on-board spares, the item descriptions should delineate the quantities intended for each use. Page 19 Prov

43、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23199/1 (SH) Revision B 14 June 2010 3.3.3.4 Standard Identifier and Serial Number as provided by the GPA. The Serial Number must match exactly the serial number marked on the equipment nameplate an

44、d shipping document. 3.3.3.5 Equipment Line Item Number (ELlN), when supplied by the GPA 3.3.3.6 Purchase Order Number 3.3.3.7 Government or Commercial Bill of Lading NumberITCN llumber/Registered NumberlWay Bill Number 3.3.3.8 Gross weight and cube of the parcel as shipped 3.3.3.9 Boxes containing

45、field change kits shall be identified with the following external markings: ShipAlt Number _ Note (a) Field Change Number _ Note (b) OBRP Are/Are Not Enclosed Note (c) Box of Note (d) TCN/Reg. No.lGBL Way Bill No. _ Note (e) Ship Hull Number _ Note (f) (al To be supplied from the GPA if available. I

46、f not available, mark “Not Available“ or “Later“ as directed by GPA (b) To be supplied by GPA. 00 NOT include project identifier (Le, S6W) (c) Mark one way or the other. OBRP, if required to support the field change, shall be packaged separately and marked (OBRP Field Change _/ShipAlt No. _) identif

47、ied on the 00-250/00-1149 by PVR line item and included in the field change box, unless specifically directed by GPA. (d) Mark each box “1 of 3“, “2 of 3“, “3 of 3“ etc. If shipment is made from a single box, mark it 1 of 1 “. Only complete kits shall be shipped unless GPA specifically authorizes sh

48、ipments of partial kits; in such cases, GPA may provide additional marking instructions to suitably indicate the shortage. (e) Enter data as applicable to the shipment (f) To be supplied from the GPA if available. If not available, mark “Not Available“ or “Later“ as directed by GPA 3.3.3.10 Precauti

49、onary note or label (must be in red): “Government-Furnished Equipment Open per Requirements of Cognizant Government Inspector“ 3.3.3.11 Precautionary note or label (must be in red): “Warehouse Storage Only“ Page 20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23199/1 (SH) Revision B 14June2010 3.3.3.12 For prim