NAVY MIL-P-85459-1983 PROBE CRUSH SENSOR RH FZU-45 B AND LH FZU-46 B AND PROBE AIR PRESSURE FZU-47 B《FZU-45 B型洛氏硬度粉碎传感器探测器 FZU-46 B LH和FZU-47 B气压探测器》.pdf
《NAVY MIL-P-85459-1983 PROBE CRUSH SENSOR RH FZU-45 B AND LH FZU-46 B AND PROBE AIR PRESSURE FZU-47 B《FZU-45 B型洛氏硬度粉碎传感器探测器 FZU-46 B LH和FZU-47 B气压探测器》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-P-85459-1983 PROBE CRUSH SENSOR RH FZU-45 B AND LH FZU-46 B AND PROBE AIR PRESSURE FZU-47 B《FZU-45 B型洛氏硬度粉碎传感器探测器 FZU-46 B LH和FZU-47 B气压探测器》.pdf(44页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-P-851159 13 9999906 036118110 5 H -04- 27 MIL-P-85459 (AS) .12 December 1983 MILITARY SPECIFICATION PROBE, CRUSH SENSOR, RH, FZU-45/B AND LH, FZU-46/B AND PROBE, AIR-PRESSURE, FZU-47/B I This specification is approved for use by the Naval Air Systems Command, Department of the Navy, and is avail
2、able for use by all Departments and Agencies of the Department of Defense. a 1. SCOPE. 1.1 Scope. This specification establishes the requirements for manu- facture and acceptance of two types of probes, referred to herein as the probe. 1.2 Classification. Probes covered by this specification consist
3、 of the following types: Type I. Probe, Crush Sensor: .c a. RH, FZU-45/B (Drawing 642AS5701). b. LH, FZU-46/B (Drawing 642AS5700). Type II, Probe, Air-Pressure, FZU-47/B (Drawing 642AS5650). 2. APPLICABLE DOCUMENTS. 2.1 Government documents. 2.1.1 Specifications and standards. Unless otherwise speci
4、fied, the following specifications and standards, of the issue listed in that issue Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commanding Officer, Naval Air Engineering Center, Engineering
5、Specifications and Standards Department (ESSD), Code 93, Lakeburst, NJ 08733, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) ap- pearing at the end of this document or by letter. I THIS DOCUMENT CONTAINS qq PAGES. Provided by IHSNot for ResaleNo reproduction
6、 or networking permitted without license from IHS-,-,-MIL-P-85459 13 979770b O364843 7 of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation, form a part of this specification to the extent specified herein. SPECIFICATIONS Military MIL-S-6872 MIL-T
7、-18303 STANDARDS Federa 1 FED-STD-102 Mil i ta ry MILYSTD-105 MIL-STD-129 MIL-STB-202 MIL-STD-331 MIL-STD-454 MIL-STD-810 MIL-STD-1246 MIL-STD-1695 MIL-STD-45662 Soldering Process, General Specifi- cation for. Test Procedures, Reproduction, Acceptance, and Life for Aircraft Electronic Equipment, For
8、mat for. Preservation, Packaging, and Packing Levels. Sampling Procedures and Tables for Inspection by Attributes. Marking for Shipment and Storage. Test Methods for Electronic and Electrical Component Parts. Fuze and Fuze Components, Environ- mental and Performance Tests for. Standard General Requi
9、rements for Electronic Equipment. Environmental Test Methods. Product Cleanliness Levels and Con- tamination Control Program. Environments, Working, Minimum Standards for. Calibration Systems Requirements. 1 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
10、IHS-,-,-MIL-P-5459 13 9999706 0364842 7 E - MIL-P-85459 (AS) 2-1.2 Other Government documents and drawings. The following other Government documents and drawings of the issue specified in the solici- tation, form a part of this specification to the extent specified herein. CODE OF FEDERAT, REGULATIO
11、NS (CFR) 49 CFR 171-178 Transportation. (Application for copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, D.C. 20402.) Naval Air Systems Command (Code Ident 30003) WS-65 36 DRAWINGS Naval- Air Systems Command (Code Ident 30003) 642AS5372 642AS569
12、8 SA498014 SA4980 15 SA2876068 642AS5356 642AS5548 642AS5 65 0 642AS5651 642AS5700 642AS5 70 1 Procedures and Requirements for Preparation and Soldering of Electrical Connections. Shipping Container Assembliy. Shipping Container Assembly. Fixture, Vibration. Fixture, Vibration. Fixture, Vibration. G
13、as Generator, BBU-32/B. Clamp Assembly. Probe, Air-Pressure, FZU-47/3. Plate, Identification. Probe, Crush Sensor, LH, FZU-46/B. Probe, Crush Sensor, RH, FZU-45/B. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-5459 13 9499906 0364843 O = 64
14、2AS5 702 642AS5 703 Plate, Identification. Plate, Identification. (Copies of specifications, standards, and drawings required by manu- facturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer . ) 2.1.3 Orde
15、r of precedence. In the event of a conflict between the 1 text of this specification and the references cited herein, the text of this specification shall take precedence. 2) and the safety wire of the safety plate assembly removed from the switch plunger, verify the resistance requirements of 3.4.2
16、.2.2 (see Figure 5 and Table IV). 4.7.4 Operational (Type I only). 4.7.4.1 Logic module operational check (Type Ia). With the Type Ia module connected to the logic module test circuit (see Figure 12), per- form the test sequence of Table V while monitoring the output voltage at test point 2. The mod
17、ule shall meet the requirements of 3.4.3.1, 4.7.4.2 Interface module operational check (Type Ib). With the Type Ib module connected to the interface module test circuit (see Fig- ure 13), perform the test sequence of Table VI while monitoring the voltage at test points 1 and 2. The resistance betwee
18、n test points 3 and 4 shall be less than 1.0 ohm. The module shall meet the requirements of 3.4.3.2. ITzq 4.7.5 Visual inspection. To determine conformance to 3.5, each probe shall be visually inspected for: a. Any external damage that may indicate impairment to opera- bility, safety, or reliability
19、 of the probe. MllO b. Safety plate assembly correctly installed (Type I andII), and safety wire through the switch plunger (Type 11). 18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-5459 13 W 799990b 03b4858 2 W MIL-P-85459 (AS) 4.7.6 Envir
20、onmental. All probes of the first article (see 4.4) and a randomly selected sample from each inspection lot (see 4.5.2) shall be subjected to the environmental tests in the sequence shown on Figure 8 at a facility designated in the contract or purchase order (see 6.2.1). Any probe subjected to these
21、 tests shall be considered destroyed and shall not be returned to the lot nor forwarded for ser- vice use. instructions from the _ procuring activity (see 6.2.1). pyrotechnic component, except when activated intentionally as part of a test, shall be considered a MAJOR defect and shall cause rejectio
22、n of the lot from which the probe was drawn. The probe shall be labeled appropriately and held for disposal Initiation of the WARNING The probe contains pyrotechnics. Proper safety precautions must be observed (see 6.4). 4-7.6.1 Temperature and humidity. To determine conformance to 3.4.4.1, test the
23、 probe in accordance with MIL-STD-331, Test 105.1. Protected covers shall be used on Type I connectors for this test. I Remain safe: C2 Remain operable: M111 4.7.6.2 Transportation vibration-temperature. To determine confor- mance to 3.4.4.2, test the probe in accordance with MIL-STD-331, Test 119,
24、Procedure 2. I Remain safe: C3 M1121 Remain operable: NOTE: For the tests of 4.7.6.2 through 4.7.6.6, the probe gasket (Figure 14, Type I; Figure 15, Type 11) shall be mounted between the probe flange and the vibration fixture. The probe and gasket shall be mounted to the vibration fixture (Drawings
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILP854591983PROBECRUSHSENSORRHFZU45BANDLHFZU46BANDPROBEAIRPRESSUREFZU47BFZU45B 型洛氏 硬度 粉碎 传感器 探测器
链接地址:http://www.mydoc123.com/p-980845.html