NAVY MIL-P-85459 (2)-1987 PROBE CRUSH SENSOR RH FZU-45 B AND LH FZU-46 B AND PROBE AIR PRESSURE FZU-47 B《FZU-45 B型洛氏硬度粉碎传感器探测器 FZU-46 B LH和FZU-47 B气压探测器》.pdf
《NAVY MIL-P-85459 (2)-1987 PROBE CRUSH SENSOR RH FZU-45 B AND LH FZU-46 B AND PROBE AIR PRESSURE FZU-47 B《FZU-45 B型洛氏硬度粉碎传感器探测器 FZU-46 B LH和FZU-47 B气压探测器》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-P-85459 (2)-1987 PROBE CRUSH SENSOR RH FZU-45 B AND LH FZU-46 B AND PROBE AIR PRESSURE FZU-47 B《FZU-45 B型洛氏硬度粉碎传感器探测器 FZU-46 B LH和FZU-47 B气压探测器》.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-P-85LI59 (2) 13 W 7979906 0369830 2 M1L-P-55459(-4S) MILITARY SPECIFICATION PROBE, CRUSH SENSOR, RH, FZU-45/B AND LH, FZU-46/B AND PROBE, AIR PRESSURE, FZU-47/B AMEND!ENT 2 1 ,lUNE. 1987 SUPERSEDING AMENDMENT 1 13 December 1984 This amendment forms a part of Military Specification MIL-P-85459(AS
2、) dated 12 Decenber-l983,-*abd is approved ZQ use withzn Ehe Naval Air Systems Command, Department of the Navy, and is available for use by all Depart- ments and Agencies of th Department of Defense. PAGE 3 Following paragraph 2.1.2, but before “CODE OF FEDERAL WGULATIONS (CFR)“, add “OTHER GOVERNNE
3、NT DOCUHENTS“ . Followingeighth line of paragraph 2.1.2, add “PUBLICATIONS“. PAGE 4 Change paragraph number “3.1.1“ to “3.7*, and “3.1.2“ to “3.8“. PAGE 5 Change paragraph number “3.1.3“ to “3.8.1“. The attached insertable replacement pages listed below are replacements for stipulated pages. When th
4、e new pages have been entered in the document,. insert the amendment as the cover sheet to the specification. Replacement Rase 35 36 Page replaced 35 Reprinted without change R . ;FSC i- 13361 THIS DOCUMENT CONTAINS o PAGES. I AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribut
5、ion unlimited. - e* Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMENDMENT 2 - PAGE 6 Paragraph 3.4.2, third line, delete “end item.“ and substitute -probe.*. Table I title, delete “type“ and substitute “Type“. Table I, fourth and fifth lines, fou
6、rth column, delete “100 Mohms“ and Substitute “50/5 Mohms 5/“; and after footnote 4/ under table, add “S/ SO Mohms applies prTor to the environmentalyincpection sequence; 5-tlohms applies during the environmental inspection sequence .a PAGE 7 Table II title, delete “type“ and substitute “Type“. Tabl
7、e 11, fourth and fifth lines, fourth column, delete “100 Mohms“ and substitute “50/5 Mohms 5/“; and after footnote 4/ under table, add “5/ 50 Mohms applies pryor to the environmental-inspection .sequence; 5-Mohms applies during the environmental inspection sequence. “ PAGE 8 Table III title, delete
8、“type“ and substitute “Type“. Table III, fourth and fifth lines, fourth Tolumn, deIete “100 Mohms“ and substitute “50/5 Mohms A/“; and after footnote 31 under table, add “4/ 50 Mohms applies prior to the environmental-inspection sequence; 5-Mohms applies during the environmental inspectkon sequence.
9、 I PAGE 9 Table IV title, delete “type“ and substitute “Type“. Table IV, fourth and fifth lines, fourth column, delete “100 Mohms“ and substitute “50/5 Mohms 4/“; and after footnote 3/ under table, add “41 50 Nohms applies pryor to the environmental-inspection sequence 5-Mohms applies during the env
10、ironmental inspection sequence. PAGE 10 Table V title, delete “type“ and substitute “Type“. Table V, Add Test 23 with the following switch settings and the following footnote 2: 2f “23 X X O O O O O 6 volts - 2/ - Test voltage to be read 5 seconds after removal of power.“ Provided by IHSNot for Resa
11、leNo reproduction or networking permitted without license from IHS-,-,-PAGE 11 Table VI title, second line, delete “type“ and substitute “Type“. Table VI, Add newTest 6 and Test 8; add footnote 2: change existing Test 6 to Test 7; 21 4 V min - I 6 O00 - 7 TP3 to TP4 1.0 ohm max 8 TP4 to TP5 1.0 ohm
12、max .% Test voltage to be read 5-seconds after removal of power.“ PAGE 12 Change paragraph number “3.7“ to “3 . 9“. Paragraph 4.1.1, second line after test, add “equipment“. Paragrap- 4.1.1.2, third line, delete “at 1eas.t“ and substitute “not less than“. Paragraph 4.1.1.3, third line, delete “3.Ll“
13、 and substitute “3.7“. PAGE 15 Paragraph 4.7 NOTE, third line, delete “4.3.2“ and substitute “4.3.4“. PAGE 16 Paragraph 4.7 . 2. la, second line? after “a“ add “minimum“. Paragraph 4.7.2.1b, first line, after “(A)“ add “minimum“; second line, after “28“ add “fl“. Paragraph 4.7.2.2b, second line, aft
14、er “a“ add “minimum“. Paragraph 4.7.2.2 first line, delete “at 28 Vdc.“ and substitute “minimum at 28 Il Vdc.“. PAGE 17 Paragraph 4.7.3, second line, delete “3.1.1“ and substitute “3.7“. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PAGE 19 Paragra
15、ph 4.7.6.1, second line, following 105.1, add: “either method, except minimum temperature shall be -65F.“ PAGE 20 Paragraph 4.7.6.3.2: Delete paragraph and substitute the following: “4.7.6.3.2 Pyro shock. To determine conformance to 3.4.4.3.2, test * the probe in accordance with the following. trans
16、ient excitation in the primary axis (see Figures 1 and 2) to satisfy in each of the two remaining orthogonal secondary axes consistent with the shock response spectrum shown in Figure 16. applied shock transients shall be between 0.Q2 and 0.15 second. analyses used to determine the shock response sp
17、ectrum shall be performed at a sequence of natural frequencies at intervals uf one sixth octave or smaller. The allowed tolerance shall be within +6 and -3 dB of the specified.acceleration. one twelfth octave shall not exceed +12 and -6 dB from the specified spec t 1: um. Subject the probe to one th
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILP8545921987PROBECRUSHSENSORRHFZU45BANDLHFZU46BANDPROBEAIRPRESSUREFZU47BFZU45B 型洛氏 硬度 粉碎 传感器 探测器
链接地址:http://www.mydoc123.com/p-980844.html