NAVY MIL-P-21593 D-1991 PANEL MARKERS RANGE FLANK AND DEBARKATION POINT NYLON FLUORESCENT《侧翼范围和下船地点荧光尼龙嵌板标记》.pdf

《NAVY MIL-P-21593 D-1991 PANEL MARKERS RANGE FLANK AND DEBARKATION POINT NYLON FLUORESCENT《侧翼范围和下船地点荧光尼龙嵌板标记》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-P-21593 D-1991 PANEL MARKERS RANGE FLANK AND DEBARKATION POINT NYLON FLUORESCENT《侧翼范围和下船地点荧光尼龙嵌板标记》.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-P-23593D 84 kl 7999906 0473246 2 I MIL-P-21593D(MC) 14 FEBRUARY 1991 SUPERSEDING MIL-P-21593C(MC) 30 December 1971 MILITARY SPECIFICATION Panel Markers: Range, Flank, and Debarkation Point; Nylon, Fluorescent This specification is approved for use by the U.S. Marine Corps, Department of the Na

2、vy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for range, flank and debarkation point panel markers. 1.2 Classification. The panel markers shall be of the and classes as specified (see 6.2): fo

3、llowing types Type 1 Type II - Range panel markers Class 1 - Yellow Class 2 - Green Class 3 - Red Class 4 - Blue Class 5 - White (Also used as the wheel vehicle debarkation point panel marker.) Class 1 - Yellow Class 2 - Green Class 3 - Red Class 4 - Blue Class 5 - White - Flank panel markers - Bene

4、ficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to the Commanding General (PSE-C), Marine Corps Research, Development, and Acquisition Command, Washington, DC 20380, by using the self-addressed Standard

5、ization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC-NA FSC 8465 DISTRIBUTION STATEMENT A. distribution is unlimited. Approved for public release; Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

6、,-Type III - Debarkation point panel markers Class 1 - Water Class 2 - Gas and Oil Class 3 - Tracked Vehicles Class 4 - Ammunition Class 5 - Rations Class 6 - Miscellaneous Supplies Class 7 - Medical Supplies 2. APPLICABLE DOCUMENTS 2.1 Government documents, 2.1.1 Specifications, standards, and hand

7、books. Unless otherwise specified, the following specifications, standards, and handbooks of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this specification to the extent specified herein. SPEC

8、IFICATIONS FEDERAL V-T-295 QQ-W-4 6 1 UU-P-268 CCC-C-476 DDD-L-20 DDD-T-86 MILITARY MIL-C-7219 MIL-G-16491 MIL-B-17757 STANDARDS FEDERAL - Thread, Nylon. - Wire, Steel, Carbon, (Round, Bare, and Coated). - Paper, Kraft, Untreated, Wrapping. - Cloth, Bunting Nylon, And Nylon And Wool. - Label, For Cl

9、othing, Equipage, and Tentage, - Tape, Textile, Cotton, General Purpose (General Use). (Unbleached, Bleached Or Dyed). - Cloth, Duck, Nylon. - Grommet, Metallic. - Boxes, Shipping, Fiberboard (Modular Sizes). FED-STD-191 - Textile Test Methods. FED-STD-751 - Stitches, Seams, and Stitching. MILITARY

10、2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-23593D 4 m 99999Ob 0473248 b MIL-STD-105 - Sampling Procedures and Tables For Inspection MIL-STD-129 - Marking For Shipment and Storage. By Attributes. (Unless otherwise indicated, copies of fe

11、deral and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094) 2.1.2 Other Government documents and publications. The following other Government documents and publications form a p

12、art of this specification to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. LAWS AND REGULATIONS U.S. Postal Service Manual (Application for copies of the manual should be addressed to the Superintendent of Documents, U. S. Government Printin

13、g Office, Washington, D. C. 20402.) 2.2 Non-qovernment Publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solici

14、tation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification Rules (Application for copies should be addressed to the Uniform Classifica

15、tion Committee, Room 1106, 222 South Riverside Plaza Chicago, Illinois 60606.) NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Application for copies should be addressed to the American Trucking Association, Inc., Tariff Order Section, 1616 P. Street, N

16、.W., Washington, D. C. 20026.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. libraries or other informational services.) These douments also may be available in or through 3 Provided by IHSNot for ResaleNo rep

17、roduction or networking permitted without license from IHS-,-,-2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. this document, however, supersedes applicable laws and regu

18、lations unless a specific exemption has been obtained. Nothing in 3. REQUIREMENTS. 3.1 Standard Sample. Standard samples are furnished solely for guidance and information to the contractor (see 6.3). Variation from this specification may appear in the sample, in which case the specification shall go

19、vern. 3.2 First article. Unless otherwise specified (see 6.2), The approval of the before production is commenced, finished panels shall be submitted, or made available to the contracting officer or his authorized representative for approval. first article authorizes the commencement of production b

20、ut does not relieve the contractor of responsibility for compliance with all applicable provisions of the specification. article shall be manufactured by the contractor in the same facilities to be used for the manufacture of the production items. The first 3.3 Materials. 3.3.1 Basic material. The b

21、asic material shall be cloth, nylon bunting, conforming to type I, class A of CCC-C-476, except that the requirements and respective quality assurance provisions for matching colorfastness and finish of CCC-C-476 shall not apply. 3.3.1.1 Color. The color of the basic material, except black, shall ap

22、proximate shades conforming to the following cable numbers : Yellow: Cable No. 70068 Green: Cable No. 70168 Red: Cable No. 70179 Blue : Cable No. 70209 White : Cahle No. 70001 The colors of the basic fluorescent material, except black and white, shall be obtained by the use of fluorescent dyes. The

23、use of fluorescent brightener is required for the white material and may be used for other colors with contracting officer approval. The fluorescent dyes and brighteners shall be those formulations adaptable to nylon cloth and shall permit high visibility during poor daylight conditions and good flu

24、orescent emission under ultraviolet excitation. The basic material, when dyed with 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-fluorescent dyes, shall show llgoodll fastness to wet and dry crocking and dry cleaning when tested as specified in S

25、ection 4, Table I. 3.3.2 Grommet reinforcement patches. The triangluar patches shall consist of a single ply of cloth, nylon duck, 7.25-ounce per square yard maximum, conforming to type III of MIL-C-7219, covered on the outside with basic material. The size of the reinforcement patches shall be show

26、n in Figure 1. 3.3.3 Bindins. Binding for the raw edges of the panels and for the raw edges of the wind holes shall be cloth, nylon, duck, 7.25-ounce per square yard maximum, olive green shade No. 106, conforming to type III of MIL-C-7219. Binding shall be cut 3-1/2 + 1/8 inches wide for edges of th

27、e panels and 1-1/8 +1/8 inches wide for the edges of the wind holes. 3.3.4 Thread. The thread for all seaming and stitching shall be nylon, twisted soft multiple cord, or twisted bonded multicord, low elongation, size B, 2-or 3-ply, conforming to type I or type II, class 1 of V-T-295. The color of t

28、he thread shall be a close approximation of the color of the material on which it is used. The color-fastness requirements of the thread shall show IgoodII fastness to wet and dry crocking and dry cleaning. 3.3.5 Grommets and washers. Grommets and spur washers shall be brass, rolled rim type, black

29、chemical finish, conforming to type III, class 3, size No.2 of MIL-G-16491. Six grommets and washers are required for each panel marker. 3.3.6 hooks. The hooks shall be made from steel wire conforming to steel No. 1015, finish 5 of QQ-W-461, except the coating weight shall not apply. The ISt1 hooks

30、shall have a zinc finish with a minimum thickness of 0.002 inch, be 5/32 inch in diameter, and conform to the dimensions shown in Figure 1. Six hooks are required for each panel marker. 3.3.7 Label. Each panel marker shall have an identification label conforming to type IV, class 1 of DDD-L-20. The

31、content and format shall be as follows. The labels shall show fastness to laundering. Nomenclature Contract number Name of contractor Stock number Fiber Products Act Information Size of characters for stock number and name of contractor shall be minimum 8 point, approximately 3/32 inch. 5 Provided b

32、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-21593D 84 999990b 0471251 b m 1 MIL-P-2 159 3D (MC) 3.4 Desiqn. Panel markers shall conform in all respects to the design and color details shown on Figures 1 through 6. All type I and II panel markers shal

33、l be in solid colors. All panel markers shall be made with wind holes. The range and debarkation panel markers shall be 6 by 6 feet and the flank panel markers shall be 12 feet long and 2-1/2 feet wide. 3.5 Construction. The construction shall conform to Figures 1 through 6 and the following. The pa

34、nel markers shall be made of single plies of basic material joined together to conform to the color and design details shown on Figures 2 through 6. The raw edges of the panel markers and wind holes shall be bound with nylon binding (see 3.3.3) as shown in Figure 1. Each panel marker shall be provid

35、ed with grommets and IlSl hooks as specified herein. 3.5.1 Stitches, seams, stitchinss. Stitch and seam types specified herein shall conform to FED-STD-751. All stitching and seaming shall be stitch type 301, 8 to 12 stitches per inch. Ends of seams and rows of stitching not caught in other seams or

36、 rows of stitching shall be backtacked not less than 1 inch. Thread breaks shall be secured by stitching back of break not less than 1 inch at each break. Thread tension shall be maintained properly so that there will be no loose stitching and the lock will be imbedded in the center of the materials

37、 sewn. All thread ends shall be trimmed. 3.5.2 Settina of qrommets and washers. Grommets and washers shall be set with all grommets placed on the face side of the panel markers. When holes are punched to receive grommets, they shall be smaller than the outside diameter of the grommet barrier so that

38、 the barrel must be forced through the hole. Grommets shall be securely clinched without cutting or otherwise damaging the material. 3.5.2.1 Location of srommets and washers. Grommets and washers shall be positioned as shown on Figure 1 and as specified herein. One grommet and washer shall be positi

39、oned at each corner of all panel markers. On type II panel markers, one grommet and washer shall be positioned not more than either of two long sides. On all other panel markers, one grommet and washer shall be positioned not more than 1/2 inch off center of either of two parallel sides. 1/2 inch of

40、f center of 3.5.2.2 Grommet reinforcement patches. Grommets and washers shall be reinforced with triangular shaped patches of nylon duck material covered on the outer side with basic material of the same color as the panel marker to which the reinforcement is sewn as shown in Figure 1. 6 Provided by

41、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.5.3 Attachment of Its“ hooks. One hook shall be attached through each grommet. The small end of the hooks shall be inserted through the grommet and bending the ends against the body of the hook. both ends shall

42、be closed by 3.6 Markina. The identification label specified in 3-3.7 shall be marked at marker at any convenient location. the center of the binding on the edge of the panel 3.7 Finished dimensions. The dimensions of the finished panel markers shall conform to the following: Overall dimensions Type

43、s I and III, length and width: 6 feet +1-1/2 inches -1/4 inch Type II: Length: 12 feet Width: 2-1/2 feet Placement of wind holes - +i inch of dimensions shown on Figures 1 through 6. +3 inches -1/2 inch +1 inch -1/2 inch 3.8 Workmanship. The finished panel markers shall conform to the quality and gr

44、ade of product established by this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified he

45、rein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the government. The government reserves the right to perform any of the in

46、spections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. this specification shall become a part of the contra

47、ctors overall inspection system or quality program. The inspection set forth in The absence of any 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-P-2L593D 84 I 7999906 0473253 T I I inspection requirements in the specification shall not reli

48、eve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract, inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, th

49、is does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. Sampling 4.1.2 Certificate of compliance. Where certificates of compliance are permitted, the Government reserves the right to check test such items to determine the validity of the certification. 4.2 Classification of inspection. The inspection requirements specified herein a