NAVY MIL-P-15280 J-1988 PLASTIC MATERIAL UNICELLULAR (SHEETS AND TUBES)《单细胞塑料材料》.pdf
《NAVY MIL-P-15280 J-1988 PLASTIC MATERIAL UNICELLULAR (SHEETS AND TUBES)《单细胞塑料材料》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-P-15280 J-1988 PLASTIC MATERIAL UNICELLULAR (SHEETS AND TUBES)《单细胞塑料材料》.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-P-LSZBOJ Sb 999990b 02LL3bB T 1pEimEGq MIL-P-15280J - SUPERSEDING MIL-P-15280H 29 March 1977 (See 6.6 MILITARY SPECIFICATION PUSTIC MATERIAL, UNICELLULAR (SHEETS“AND TBW This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This
2、specification establishes the requirements for chemically expanded unicellular elastomeric plastic foam material for thermal insulation. 1.2 Classification. Plastic foam shall be of the following forms, as specified (see 6.2.1): Form T - Tubular. Form S - Sheet. 2. APPLICABLE DOCUMENTS 2.1 Governmen
3、t documem. 2.1.1 SDecifications and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specification
4、s and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL PPP-B-636 - Boxes, Shipping, Fiberboard. PPP-F-320 - Fiberboard; Corrugated and Solid, Sheet Stock (Container Grade), and Cut Shapes. Beneficial comments (recommendations, additions, deletions) and any
5、 pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of th
6、is document or by letter. msc N/A FSC 5640 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-LS2BOJ Sb 7999906 02LL3b9 L = MIL-P- 152805 MILITARY MIL-P-116 - Preser
7、vation, Methods of. MIL-L-19140 - Lumber and Plywood, Fire-Retardant Treated. MIL-A-24179 - Adhesive, Flexible Unicellular-Plastic Thermal Insulation. STANDARDS FEDERAL FED-STD-313 - Material Safety Data Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities
8、. MILITARY MIL-STD-293 - Visual Inspection Guide for Cellular Rubber I terns. Variables for Percent Defective. fications For Interior Finish Materials and Furnishings (Naval Shipboard Use). Application of Packaging Requirements. MIL-STD-414 - Sampling Procedures and Tables for Inspection by MIL-STD-
9、1623 - Fire Performance Requirements and Approved Speci- MIL-STD-2073-1 - DoD Materiel Procedures for Development and 2.1.2 Other Government Dublication. The following other Government publication forms a part of this specification to the extent specified herein. Unless otherwise specified, the issu
10、e shall be that in effect on the date of the solicitation. DEPARTMENT OF TRANSPORTATION (DOT) Communication Standard. Code of Federal Regulations, Title 29, Part 1910.1200 - Hazard (The Code of Federal Regulations (CFR) and the Federal Register (FR) are for sale on a subscription basis by the Superi
11、ntendent of Documents, U.S. Government Printing Office, Washington, DC 20402. When indicated, reprints of certain regulations may be obtained from the Federal agency responsible for issuance thereof. ) (Copies of specifications and standards required by contractors in connec- tion with specific acqu
12、isition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other DubliCatiOnS. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adop
13、ted shall be those listed in the issue of the DoDISS specified in the solicitation, Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the non-government documents which is current on the date of the solicitation. 2 Provided by IHSNot for ResaleNo repr
14、oduction or networking permitted without license from IHS-,-,-MIL-P-15280J Sb 999990b 02LL370 8 MIL-P-15280J AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) C 177 - Standard Test Method for Steady-State Heat Flux Measure- ments and Thermal Transmission Properties by Means of the Guarded-Hot-Plate
15、Apparatus, (DoD adopted) ments and Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus. (DoD adopted) Liquids. (DoD adopted) Sponge or Expanded Rubber. (DoD adopted) Vinyl Chloride Polymers and Copolymers (Closed-Cell Foam). (DoD adopted) (DoD adopted) Materials. (DoD adopted)
16、C 518 - Standard Test Method for Steady-State Heat Flux Measure- D 412 - Standard Test Methods for Rubber Properties in Tension. D 471 - Standard Test Method for Rubber Property - Effect of D 1056 - Standard Specification for Flexible Cellular Materials - D 1667 - Standard Specification for Flexible
17、 Cellular Materials - D 3951 - Standard Practice for Commercial Packaging. E 96 - Standard Test Methods for Water Vapor Transmission of (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards a
18、nd other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through 1i.braries or other informational ser-rices. ) 2.3 Prder of Drecedence. In the event of a conflict between the text of this specifi
19、cation and the references cited herein, the text of this specifi- cation shall take precedence, Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained . 3. REQUIREMENTS 3.1 gualificatioq. The plastic foam material furnish
20、ed under this specification shall be products which are authorized by the qualifying activity for listing on the applicable qualified products list at the time set for opening of bids (see 4.3 and 6.3). 3.2 Dimension and tolerance. The dimensions of plastic foam material shall be as specified (see 6
21、.2.1). Tubular form of material up to 5-3/4 inches inside diameter (id) shall be extruded and shall have no seams, slits or chemically bonded joints and shall not be manufactured from flat sheets. Sheet form of material shall be seamless. Unless otherwise specified (see 6.2.1), tolerances shall be a
22、s specified in table I. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dimensional tolerance of sheets and tubinq. Nominal thickness (inches) Dimension Sheets Up to 1/4, inclus ive 3ver 1/4 to 1/2 3ver 1/2 to 1 aver 1 Tubular form up to 3
23、/4, inclus ive her 3/4 Tolerance t3/32 t3/32 t3/32 - 1/32 - 1/32 ;1/8 -0 to +1/8 -0 to +3/16 Length and width (inches) Dimension Up to 6, Over 6 to 12, Over 12 inclus ive inclus ive Tolerance t1/4 t3/8 3 percent -1 to +4 -1 to +4 tnside diameter (inches) Dimension Jp to 1/2, inclus ive her 1/2 to 1,
24、 inclus ive )ver 1 to 1-1/2, inclus ive her 1-1/2 inclus ive her 2-3/8 to 2-3/8, Tolerance *O to +3/32 .O to +1/8 .O to +3/16 .O to +1/4 ,o to +3/8 - 1/ Number of sheets or length of tubing shall be as specified (see 6.2.1). 3.3 Finish. Unless otherwise specified (see 6.2.1), sheets and tubes shall
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILP15280J1988PLASTICMATERIALUNICELLULARSHEETSANDTUBES 单细胞 塑料 材料 PDF

链接地址:http://www.mydoc123.com/p-980527.html