NAVY MIL-K-24030-1964 KIT AMPHIBIOUS WARFARE EXERCISE《两栖战演习工具箱》.pdf

《NAVY MIL-K-24030-1964 KIT AMPHIBIOUS WARFARE EXERCISE《两栖战演习工具箱》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-K-24030-1964 KIT AMPHIBIOUS WARFARE EXERCISE《两栖战演习工具箱》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、13 March 2964 SUPERLCEDING NAVTRADEVCEN 3144 -120 17 September 1957 mLITARY SECEFICATION KIT, AMPHIBIOUS WARFW EXERCISE This specification has been approved by the Office of Naval Research (W, S, Naval Training Device Cen.t;er), Department of the Navy. c 1.1 This specification covers one type,of amp

2、hibious warfare exercise kit for use as a training aid by presenting Che ship-to-shore movement of an amphibious operatdon. l.l*l This item has been designated by the Office of Naval Research (U. S. Naval Training Device Center) as Device 163 for Navy procurement (see 6,s) 2, APPLICABLE DOCWWS 2.1 T

3、he follotring documents of the issue in effect on the ate o% invikation for bids or regues% for proposal, farm a part of this specifica- tion to the extent specified herein, SPECIFICATIONS Federal PPP-B-601 PPP-B -621 PPP-B-636 Military MTL-P-L MIL-fi-10547 Boxes3 Woo, Cleated-Plywood Boxes; IJasd,

4、Nailed arrd Iaek-Cbmer Ebx, Fiberboar Methods of Liners, Case and Sheet,Overwrap, Wai;er-Vipmproof or Waterproof, IXiexibJe Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-K-24030 67 M 7777706 0383776 4 M Federal FED - STD -53 (r Colors Military

5、bEL-STD-129 Marking for Shipment and Storage DRAWINGS U. S. Naval Training Device Center A625149 Drawing List, for Device 163 (Copies of specff icatrbona , standards, drawings, and publications required by suppliers in conne,ction with specific procurement functions Chould be obtained from the procu

6、ring activity or as directed by the contracting officer. ) 3. T(EQUIREMENTS .1 Materials o - Unless otherwise specified herein, mat&riais shall be as specifbd on the deta+l drawings of 2.1. Materials not specified herein or on the drawings shall be selected on the basis of compatibility with the est

7、ablished design and suitability for the purpose intended. 3.2 Design.- The kit as shown on the detail drawings of 2.1 shall consist of all the necessapy material and equipment for presenting amphibious operation. the same part number shall be directly and completely interchangeable with each other w

8、ith respect to installation and performance, regardless of sources from which obtained, without alteration and without selection for fit or performance. 3.2,l Interchangeability.- ALL parts, subassemblies an.assembes:haaing 3.3 Constructiond- Construction shall be as shown on the detail drawings of

9、2.1-and the following: 3.3.1 Metal standse- The aluminum stands, item 5, listed on Drawing C62W35, aqrawing A625149 shall hold all index cards at an angle of approximately 30 degrees from the vertical, 3.3.2 The ship and a5rcraft models, and the land area of the terrain board shall be constructed by

10、 utilizing the Government-loaned molds, 2 . ,- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-7. MIL-K-2q030 67 m 7777706 0383977 b m MIbK-2b30(0NR/NTDCTac) 3.3.3 small eye hooks shall be installed on the sterns of 50 ship models as designated on th

11、e detail drawings of 2.1, 3.4 Details of components.- The kit shall consist of the following major components, the details of which shall be as shoim on the dew1 drawings of 2.1: a) Model ships and aircraft (275) Plastic boxes, clear (6) Carrying case Il Accessories. 3.5 Dimensions.and tolerances,-

12、Dimensions and tolerances shall be as shown on the detail drawings of 2.1. Tolerances not shown on the drawings shall he maintained to assure meeting the interchangeabilitymquirements, b) Sea area terrain bmrd e) Und area terrain board I 3.6 Finish and color.- Finish and color sh&U be as shown on th

13、e detail 3.6.1 The carrying case shall be smoothly sanded, sealed and then drawings OP 2.1 and the following: finished with two coats of gray semi-gloss paintt number 26259 in accordance with StWdWd FED-STD-595 c 1 3.7 Nameplates or product markings-,- 3.7.1 NamepLa$e.- A Government-furnished namepl

14、ate shalt1 be &fixed to Che kit in the location shown on the detail cbawhgs of 2,L. 3.7.2 Marking of components,- The top ou-bside of the carrying case shall be marked in black $-inch 3igh letters with $he device name and device designation, 3.8 +vernment-furnished property.* One U, S, Ra.va Trainin

15、g ikvice 3.9 Government-loaned property.- The following property will be loaned Center nameplate will be nirnshed by the Government for each kit, by the Government: . klds for ships and aircraft (6) 3,lO Workmanship.- The kit shall be constructed and finished with particular atten-bion given 80 neat

16、ness an thoroughness of marking of parts and assemblies, sanding and painting. - -.ri- f- 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-K-24030 69 979790b 0383978 8 9 - I , - - MIL-K-24030 (ONR/NTDcI) 4.1 Responsibility for inspection,- Unles

17、s otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requiigements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any comercial laboratory acceptable to the Guvernment. right to

18、perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirementso The Government reserves the 4.2 Classification of inspection. - Inspections to be performed are classified as follows: a) in-p

19、rocess inspection b) Quality, Conformance inspection. 4.3 In-process iospection, - In-process inspection shall include such visual and mechanical examinations and testing of materials, subassemblies, parts, and accessories (including purchased standard items)during the manufacturing process as may b

20、e necessary to assure conformance to all the requirements specified. herein e 4.4 Qudity conformance inspection. - 4.4.1 Preproduction inspection. - Preproduction inspection shall be conducted on the preproduction sample and shall consist of all the examina- tions specified herein. 4.4.2 Production

21、inspection.- Production units shall be inspected to the extent necessary to maintain quality control and conformance to the Government-accepted preproduction sample. 4 5 Examinations .,- Examinations shall be performed to verify conformance to the following requirements: (a) Materials :. (b) Constru

22、ction (c) Dimensions and tolerances (a) Finish and color (e ) (f ) Workqanship ( Q) Nameplate s or product markings Weparat ion for deivery . 5. PREPARATION FOR DELIVERY 5.1 Preservation and packaginge- Preservation and packaging shall be level A or C (see 6.2), Provided by IHSNot for ResaleNo repro

23、duction or networking permitted without license from IHS-,-,-MIL-K-OO ( ONR/NTDC) 5.i.i Level A.& For level A, each kit shaL1 be preserved and packaged for mechanical and physical protection in accordance with Specification MIL-P-, Method III. 5,l,l,l Unit packaging.- Each kit shall be packaged one

24、unit to a container conforming to Specification PP-B-636. 5.1.2 Level C.- For level C, preservation and packaging shall conform to manufacturer%s commercial practice. 5.2 Packing - Packing shall be level A or C (see 6.2) 52.l Level A,- Units packaged in accordance with 5.1.1 shall be pack&d in exter

25、ior containers conforming to Specifications PPP-B-601 or PPP-3-621 b Unless otherwise specified by the procuring activity (see 6.2), the gross weight shall not exdeed the weight limitations of the shipping container, Each exterior shipping container shall be lined with a waterproof moisture barrier

26、sealed with adhegive or tape to effect water resistance in atm+ We with Specification MIL-L-10547. A case liner sha3i1 not be required where the package(s) and package dunnage have been treated to resist water. Unit fiber boxes, conforming to Specification PPP-B-636, class 2, closed, reinforced and

27、waterproofed as specified in the appendix there%o, and used as shipping containers, shall hot be overpacked. 5.2.2Level C.- Units packaged in accordance with 5.1.2 shall be pakked in containers which will insure acceptance by common carrier and safe delivery at destination. Shipping containers shall

28、 comply with common carrier mies and regulations as applicable to the mode of trans- portation and may be the suppliers commercial practice when such meets the requirements of this level. 5.3 Physical protection.- Ali material shaU be packaged and packed in containers constxhcted to provide a compac

29、t and nonshifting load. Adequate cushioning, blocking and bracing shall be provided within shipping con- tainers in a manner designed to prevent damage due to shock, vibration or impact during shipment, handling and storage. 5 .4 Bhrking. - Interior packages and exterior shipping containers shall be

30、 marlred in accordance with Standard MIL-STD-129. 6.1 Xntended se.- The kit will be used for classroom instruction on 6.2 Ordering data. - FTocurement documents should specif y the f ollowSng : ship-to-shore movement and associated phases of amphibious operation. (a) (b) Title, number, and date of t

31、his specification Frocuriqg activity designation (device number or other) (see 1.1.1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-K-24030 69 779770b 0383980 b (c) (d) Selection of applicable levels of preservation, packaging and Gross weight

32、of shipping container (see 5.2,l) . . packing (see 5.1 and 5.2) 6.3 Def initionsc-Except as specified herein, dei initions will be furnished upon matten request to the procuring activity, 663,1 Preproduction sample+- A production item furnished under production contracts for the purpose of determini

33、ng compliance with reqirements of the - detail training device specification already established and accepted, shall be electrically and mechanically representative of production sets though not necessarily made with production line jigs, fixtures and methods. It 6.3.2 Production unit.- A unit in it

34、s final mechanical and electrical form of final production design made by production tools, jigs, fixtures and methods e 6.3*3 Training aid,- A training device designed to demonstrate or illustrate a concept. Preparing activity: Navy-ONR (WTDC ) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-