NAVY MIL-I-15864 K-1990 INSIGNIA EMBROIDERED (MEN AND WOMEN)《装饰徽章(男式和女式)》.pdf

《NAVY MIL-I-15864 K-1990 INSIGNIA EMBROIDERED (MEN AND WOMEN)《装饰徽章(男式和女式)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-I-15864 K-1990 INSIGNIA EMBROIDERED (MEN AND WOMEN)《装饰徽章(男式和女式)》.pdf（45页珍藏版）》请在麦多课文档分享上搜索。

1、hNCH-POUND( MIL-I-l5864K(NU) 7 September 1990 SUPERSEDING 18 January 1984 MIL-I-l5864J(NU) MILITARY SPECIFICATION INSIGNIA, EMBROIDERED (MEN AND WOMEN) This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and. is available for use by all

2、Departments and Agencies of the Department of Defense. -. -t. . . 1. SCOPE * 1.1 Sc0 e. This specification covers the requirement for Schiffli and hand embroi h% ere sleeve insignia worn by enlisted men and women of the Navy and Navy personnel attached to the Marine Corps units. 1.2 Classification.

3、Embroidered insignia shall be of the following types and classes. (see 6.2): Type I - Badge, Rating Class 1 - Chief Petty Officer Class 2 - Petty Officer - First Class Class 5 - Master Chief Petty Officer Class 6 - Senior Chief Petty Officer Class 7 - Master Chief Petty Officer of the Navy . . . Typ

4、e II - Specialty Mark and Striker Mark (see Table III) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick,

5、 MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8455 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction

6、 or networking permitted without license from IHS-,-,-Type V - Group - Rate Mark Class 2 - Two Stripes Class 3 - Three Stripes Type VI - Stripe, Service Class A - 7 inches long Class B - 5-1/4 inches long * Class C - 7 inches long (synthetic metallic yarn) - . * Class D -.5-1/4 inches long (syntheti

7、c metallic yarn) Type VI11 - Insignia, Grade Type X - Badge, Rating, Utility, Petty Officers, First Class 2. APPLICABLE UUCUMENTS . ,. - 2.1 Government documents. : 2*1;1 Specifications, Standards , and Handbooks The following specifications, standards, and handbooks form a part of this document to

8、the extent sp.ecified herein. Unless otherwise specified, the issues ofa these .documents shall be those listed in the issue of the Department of Defense .Index -of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). ,-. - SPECIFICATIONS FEDERAL V-T-.2

9、7 6 - Thread, Cotton PPP-B-676 - Boxes, Set-up MILITARY MIL-C-823 . MXL-c-3738 MIL-C-10176 MIL-C-16290 MIL-L-17507 MIL-E-17568 - MIL-B-17757 MIL-1-18496 MIL-C-21115 MIL-C-21881 * MIL-(2-24910 MIL-C-29127 MIL-C-43482 MIL-C-87052 - Cloth, Serge, Wool, Wool and Nylon, Polyester - Cloth Elastique, Wool

10、- Cloth, Gabard-ine, Wool, Polyester, and Wool - Cloth, Melton, Wool (Moth Proofed) - Lace, Ornamental - Embroidery Materials, Metallic and Synthetic, . and Wool Metallic . .- Box, -Shipping, Fiberboard (Modular Sizes) - Insignia, Embroidered (Womens) - Cloth, Tropical, Wool, Polyester/Wool - Cloth,

11、 Poplin, Polyester and Cotton - Cloth, Tropical: Polyester and Wool - Cloth, Twill, Polyester/Cotton (Crease-Resistant - Cloth, Poplin: Cotton and Polyester, Water - Cloth, Twill, Polyester, White Finish) Repellent 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

12、e from IHS-,-,-MIL-I-l5864K(NU) STANDARDS FEDERAL FED-STD-191 - Textile Test Methods FED-STD-751 - Stitches, Seams and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables For Inspection By MIL-STD-129 - Marking For Shipment and Storage Attributes * MIL-STD-2073-1 - DoD Materials Procedu

13、res Development and * MIL-STD-2073-2. - Packaging Requirement Codes Application of Packaging Requirements * (Unless otherwise indicated, copies of Federal and Military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue,

14、Philadelphia, PA 19111-5094) * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DR

15、AWINGS (Stitch enlargement drawing numbers are as indicated in Table III. Figures 1 through 16 are illustrations of Navy Clothing and Textile Research Facility stitch enlargement drawings, and are attached for information only.) * U.S, POSTAL MANUAL (Copies of the manual may be obtained from the Sup

16、erintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-0001.) * 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be thos

17、e fisted in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classificati

18、on (Applications for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-l5864K(NU) UNIFORM CLASSIFICATION

19、 COMMITTEE, AGENT Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification -Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808.) TIE COLOR ASSOCIATION OF THE UNITED STATES Standard Shades for Heraldic Yarns for Embroidery an

20、d Ribbons Standard Shades for Sewing Threads (Applications for copies should be addressed to the Color Association of the United States, 343 Lexington Ave., New York, NY 10016-0927.) % (Non-Government s.tandards and other publications are normally available from the organizations that prepare or dis

21、tribute the documents. These documents also may be available in or through libraries or other informational services.) * 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this

22、document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3, REQUIREMENTS 3.1 .Guide Sam le. Samples, when furnished, are solely or guidance and informat -x-” on to t e contractor (see 6.3). Variations from this specification may appear in the sampl

23、e in which case this specification shall govern. to first article inspection in accordance with 4.3. 3.2 First article. When specified, (see 6.2), a sample shall be subjected -3.3 . Materials. 3.3.1 Cloth, Wool, Melton. The melton shall conform to the requirements for type Idfcept the color shall ma

24、tch Blue 3346. * 3a3.2 Cloth, -Wool, Elastique. The elastique shall conform to the requirements for type I or type II, class 2 of MIL-C-3738. The color shall match Green 2222. *-3.3.3 Cloth, Gabardine, Wool, Polyester and Wool. The gabardine shall . conform to the requirements for type I, class 5 of

25、 MIL-C-10176. The color shall match Blue 2316(MC). The fabric for the Marine Corps shall conform to type II, class 12 .of MIL-C-10176. The shade shall be Green 2212, 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* 3.3.4 Cloth, Tropical. The cloth

26、, tropical shall conform to the requirements of type III, class I, Khaki 3729 or type III, class 3, Blue 3346 of MIL-C-21115. The color for the Marine Corps shall be Green 2241. 3.3.5 Cloth, Wool, Serge. The serge used shall conform to the requirements of type I, class 5, of MIL-C-823. The colors sh

27、all match Green 2234 (MC) and Blue 3346 (Navy). 3.3.6 Cloth, Twill, Polyester/Cotton. The twill material.shal1 conform to the requirements of class 1 or 2 of MIL-C-29127. The color for class 1 shall - be Khaki 2101 (MC). The color for class 2 shall be White 3053. 3.3.7 Cloth, Poplin, Polyester, and

28、Cotton. The material shall conform to the requirements of type II, class 2 of MIL-C-21881. The color shall match White 3013. 3.3.8 Cloth, Poplin, Cotton and Polyester, Water Repellent. The poplin material shall conform to the requirements of MIL-C-43482, except that the requirements for water repell

29、ency and seam efficiency shall not apply. The color shall match Blue 3329. * 3,3.9 Cloth, Tropical: Polyester and Wool. The cloth to be used as a background for embroidered designs shall conform to the requirements of MIL-C-24910. The color shall be Blue 3346. NOTE: Background fabrics applicable to

30、womens striker marks shall be specified in MIL-1-18496, Insignia, Embroidered (Womens) * 3.3.10 Cloth, Twill, Polyester. The cloth to be used as a background for embroidered designs shall conform to the requirements of MIL-C-87052. The color shall be White 3053. NOTE: Background fabrics applicable t

31、o womens striker marks shall be specified in MIL-1-18496, Insignia, Embroidered (Womens) 3.3,11 Embroidery materials, metallic and synthetic metallic. The embroidery materials shall conform to the requirements f6r type I, II, or III Of MIL-E-17568. 3.3.12 Lace, ornamental. The gold lace shall confor

32、m to the requirements for type II, style A, class 2, 3, 4, or 5, 3/8 inch in width, one or two vellum of MIL-L-17507. The color shall match Gold 3903. 3.3.13 Buckram. The cotton buckram shall be natural or bleached white, plain weaveandshall conform to the following requirements when tested as speci

33、fied in 4.4.1. Type A - - - 50 (+3) ends and 50 (53) picks per inch. The weight Type B - - - 20 (+2) ends aid 15 (2) picks per inch. The weight shall be 4.8 (+1 .O) ounces per square yard. shali be 6.75 (+l. - O) ounces per square yard. 5 Provided by IHSNot for ResaleNo reproduction or networking pe

34、rmitted without license from IHS-,-,-MIL-I-l5864K(NU) 3.3.131 Buckram backing. Unless otherwise specified, buckram backing shall be used to reinforce the following areas of insignia: Type A - Hand-embroidered bullion or synthetic metallic stars, eagle and specialty mark of rating badge. Sewn on type

35、 gold lace chevrons and service stripes. * Type B - One lajrer of bleached buckram when the white polyester background cloth conforming to MIL-C-87052 is used. * Types A and E - Buckram reinforcement is not required but may be used on . _. Schiffli embroidered synthetic metallic stars, eagle, specia

36、lty mark, chevrons, and service stripes. 3.3.14 Yarns - Schiffli embroidered insignia. * 3.3 . 14.1 Ra on arn. The rayon yarn shall be bright, continuous filament , regenerated ce -“- u ose type, 7513 (I- 5) denier Schiffli yarn. The rayon yarn for the eagle tongue for Petty Ofricer 3rd Class and ab

37、ove. shall be bright, continuous filament, regenerated cellulose type, 100/2 (t 5) denier or 75/3 (+ 5) denier Schiffli yarn. Testing shall be as specified i 4.4, l. * 3.3.14.1.1 Colors. Cable numbers for the colored yarns shall be as follows (see 2.2 and 6,2),The use of sulfur dyes is prohibited. W

38、hite - Cable No. 67101 Golden Yellow - Cable No. 67104 Scarlet. - Cable No. 67111 Blue Bird - Cable No. 67117 Emerald Green - Cable No. 67128 Dark Blue - Cable No. 67126 * 3.3.14.1.1.1 Colorfastness. The yarn shall show fastness to light, laundering, wet-dry cleaning, bleaching and dry and wet heat

39、(hot pressing), equal to or better than the standard sample when tested as specified in 4.4.4. As a limit of acceptability or when no standard sample is available, the yarn shall show good fastness to light, laundering, wet-dry cleaning, bleaching and dry and wet heat (hot pressing) when tested as s

40、pecified in 4.4.1. . . * 3.3.14.1.2. Matchin . The dyed yarns shall match the available standard shade sample W d en v ewed under filtered tungsten lamps that approximate artificial daylight, having a correlated color temperature of 7500 (t 200) K with illumination of 100 (t 20) foot candles and sha

41、ll be a good matcl to the standard shade sample undeF incandescent lamplight at 2300 (+ - 200) K. * 3.3.14.2 Bobbin thread. The bobbin thread used in Schiffli embroidery shall either be a good commercial grade of two-ply (minimum) undyed cotton thread or continuous filament undyed (white) nylon thre

42、ad equal to or better than the quality of the specified cotton thread when tested as specified in 4.4.1. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-l5864K(NU) * 3.3.14.3 Synthetic metallic yarn. As an alternate to the yarn specified in 3

43、.3.14.1, the yarn for the type VI Service Stripe, Classes C and D (see Table III) shall conform to type III, Class 8 or 11 of MIL-E-17568. Testing shall be as specified in MIL-E-17568. Design and construction requirements shall be as specified in 3.6.5. * 3.3.15 Thread, cotton. The white or colored

44、thread used for cover stitching and hemming shall conform to the requirements of V-T-276 and as specified in Table I. Unless otherwise specified, the color of the thread shall match the color of the fabric used as the background cloth. * 3.3.15.1 .Colorfastness. The thread shall show fastness to dry

45、 and wet heat (hot pressing), equal to or better than the standard sample when tested as specified in 4.4.1. As a limit of acceptability or when no standard sample is available, the yarn shall show ttgoodlf fastness to dry and wet heat (hot pressing) when .tested as specified in 4.4.1. Table I - Thr

46、eads Type Ply Ticket Number Operations Needle Lower 1Al 3 40 - Attaching metallic embroidery materials by hand 1c1 3. O0 O0 Hemming and cover stitching 1c2 3 O0 O0 Hemming, attaching gold lace, (whi te) coverstitching (colors) 3.3.16 Form, fiberboard. When needed, the form used to raise the design o

47、f hand embroxdered metallic insignia shall be a commercial grade fiberboard of sui table thickness and shall be free of sulfur (see 4.4.1). The face side of the board shall be a color to approximately match the color of the embroidery material covering it. 3.3.17 Stiffener. When needed, hand embroid

48、ered insignia may be treated on the reverse side with a stiffener to facilitate processing or to prevent raveling of the yarn. The stiffener shall not affect the color of the face of the insignia or the background fabric while in storage. 3.3.18 Stitches, seams, and stitchings. Stitch types shall co

49、nform to FED-STD-751. Stitch type 301 used for hemming shall be 1/8 (+ 1/32) inch from the edge. Stitch type 304 used for cover stitching shall be T/8 (+ 1/32) inch wide. Stitches per inch shall be 12 to 14 for general stitching and 45 to 48 for cover stitching. * 3.4 Descri tion. The insignia specified in this specification shall be either Schiff11 em roidered with rayon yarn and/or synthetic metallic material in accordance with the applicabl