NAVY MIL-G-82241 C (2)-1985 GLOVE INSERTS RADIOACTIVE CONTAMINANTS PROTECTIVE《防止放射污染的嵌入式手套》.pdf

《NAVY MIL-G-82241 C (2)-1985 GLOVE INSERTS RADIOACTIVE CONTAMINANTS PROTECTIVE《防止放射污染的嵌入式手套》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-G-82241 C (2)-1985 GLOVE INSERTS RADIOACTIVE CONTAMINANTS PROTECTIVE《防止放射污染的嵌入式手套》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、M L I, ITARY SPEC IF LCAT ION MIL-G-82241C Amendment-2 10 July 1985 SUPERSEDING Amendment-1 26 April L983 - - GLOVE LNSEKS , RADIOACTIVE CONTAMINANTS PROTECTIVE This amendment orms a part of Military Specification MIL-G-82241C, dated 17 .iiiitiary 1979, and is approved for use by all Departments and

2、 Agencies of the Department of Defense. Page 1 2.1 - Deleto and acid the following: “2.L Government documents. - -. - .- - 2.1 .I Specifications, standards, and handbooks. -_ _- .- - speci Eied the following specifications standards and hant listed in that issue of the Department o Defense index of

3、Standards (DoDISS) specified in the solicitation form specification to the extent specified.“ Unless otherwise looks of the issue Specifications and a part of this Under “Specifications, Federal“ add the following document - “NN-P-I1 - Pallet, Material Handling, Wood, Stringer Construction 2 Way aii

4、cl 4 Way“ iJnder “Specifications, Military“ add the Following document - “MIL-P-15011 - Pallet Material Handling; Wood Post Construction 4 Way Lit r y“ Page 2 Under “Standards; Military“ - add new standard - “Ml,-STD-147 - Pallet ized unit Loads“ Add new paragraph: “3.3 - Order - of Precedence. -.-

5、- In the event of a conflict hetwec!ii the text OE this document and the references cited herein, the text of this dociimizrit shali take precedence .“ Page 3 Add new paragraph. “3.3.3. Vulcanization. - As an alternate the glove seams nay be joined by an injection process using any commercially avai

6、lable latex material and vuicanized in accordance with the time and temperature requirements of the glove manufacturer .“ FSC 8415 DISTRIBUTION STATEMENT A - Approved for public release; distribut ion is unlimited. THIS DOCUMENT CONTAINS PAGES Provided by IHSNot for ResaleNo reproduction or networki

7、ng permitted without license from IHS-,-,-I 3.4 - Delete paragraph in its entirety and substitute: “3.4 Decigii. TILE gloves shall be a 5-finger silhouette, arnbidex!:rous design, joined by either stitching or vulcanization, as shown in Figure. 1. “ 3.5 - At end of paragraph add: “As an alternate, t

8、he contractors working patterns may exc.1udi.t tiit: 1/3 inch cut or tirim Iiiie marked on the Vover:iinent patterns, but sliall re:iraLn the same in alL other respects.“ Pagp 4 3.5.1 - kt tnd of paragraph ad: “(:;ce 3.S)“ “ 3.6.3 - 3elei:e in its entirety and iuhstitiite: “3.6.3 Thread breaks Threa

9、d breaks (ill stitch yils) c!;.i11 ht: secured by stitchiiig back of break: not 1e7ijcj tiiari L!2 inch. Skipped htitche.; or thread-breaks (461 stcch types) niay be repaired using 301 c1.i tcli Lypt. Table IL, operation I, Line 4 - add: “(see 3.5.“ Operation 2, delete i.n its entirety and substitut

10、e the EoLLowing: 1 “Assemble gloves. a. Stitch two component: parts 1!2 inch from outer tdaes, (:xr.ept aL top opening . OR b, Iiiject latex material between two component parts, L/b inch from outer edges, except at top opening. C. Vulcanize seams in accordance with the time arid temperature require

11、ments of the glave manufacturer. d. There shall be no pickers, pleats or aseas o poor adhesion. NOTE: A i/8 inch seam allowance shall be trimmed off either driring or after joining operation. hheii contractors working patterns do not lise the cul: or trim line, the gauge of joining shall be l/S inch

12、 from the outer edge.“ Operation 4, delete in its entirety. 1 2 .- fa Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* MIL-G-8224LC (2) 84 7777706 0406782 7 W MIL-G-82241C Amendment-2 Page 6 3.8 - AC end of paragraph add “AL1 measurements shall be m

13、ade between st Ltch or vulcanization lines .“ Page 8 4.4.2.1 - SEAMS ANI) STTCHINGS2 delete defects a.2, a.3 and a.4 in their en t i. re t y Page 9 4.4.2.L - SEAMS AND STITCHINGS defect a.6, line 1 - delete: “Inseam“ and siihst itiite “Seam.“ Before “ASSEMRLY DETAIL“ add the Eollowing : “VULCANIZED

14、SEAMS a Any open seam (Eor any distance) Major b. Pucker, pleat or area of poor adhesion Major“ ASSEMBLY DETAIL, defect b - delete in its entirety. Page 10 4.4.3 - At end of paragraph add: Examine Defect Marking (exterior Omitted, incorrect, illegible, of improper size, - - location, sequence, or me

15、thod of application. Mate I: ;.ai s Any component missing, damaged or not as specified Workinan ship Con tent Inadequate application of components such as improper taping, incomplete closure of container Elaps, loose strapping, or inadequate stapling. Bulged or distorted container. Number of bundles

16、 per shipping container is more or Number of pairs of gloves per bundle is more or less less than required than specified. - i/ _- i/ For this deEect, one bundle shall be examined from each shipping container in tiic samp1.e. Provided by IHSNot for ResaleNo reproduction or networking permitted witho

17、ut license from IHS-,-,-MIL-G-224LC (2) 4 W 777770b 0406783 O W MIL-G-82241C Amendment-2 Add new paragraph: , 4.4.4 Palletization examination. An examination shall he made to determine that the pallet ization complies with the section 5 requirements. Defects shall be scored in accordance with the li

18、st below. The sample unit shall be one palletized unit load fully packaged. The lot size shall be the number of palletized unit loads in the end item inspection lot. The inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5. Examine Defect Finished

19、dimensions Length, width, OK height exceeds specified maximum requirements. Palletization Pallet pattern not as specified- Interlocking of Loads not as specified. Load not bonded with required straps as specified Weight Exceeds maximum load limits. Mar king Omitted, incorrect, illegible, of improper

20、 size location, sequence or method of application. 5.2.1, line 3 - Delete “grade VS, size 1“ and substitute “type CF, size lA, variety DW, grade V15c“. line 4 - Following “MIL-B-17757.“ add “The liner will be type CF, class domestic in accordance with the requirements specified in MIL-B-17757.“ 5.2.

21、2, line 3 - Delete “size 1“ and substitute “size A, variety DW, type CF . “ Following “MIL-B-17757.“ add “The liner will be type CF, class domestic. in accordance with the requirements specified in MIL-B-17757.“ Add new paragraph 5.2.4 - Palletization. When specified (see 6.2). glove inserts, packed

22、 as specified in 5.2 shall be palletized on a 4-way entry pallet in accordance with load type IA of MIL-STD-147, Each prepared load shall he banded with primary and secondary straps in accordance with the banding means (C, K and L) or O or P. Pallet patterns shall be in accordance with the appendix

23、of MIL-STD-147. The pallet shall be 4-way, Type III. Class 1 Style A Size 2, wood group I, Grade A of NN-P-71, or 4-way, Style (1, 1A or 1B) , Size A, Type I Class 1 of MIL-P-15011. Interlocking of loads shall be efEected by reversing the pattern of each course. If the container is of a size which d

24、oes not conform to any of the patterns specified in MIL-STD-147 the pallet pattern used shall first be approved by the contracting ofEicer. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-777970b 0406784 2 _- MIL-G-8224LC (2) 84 MIL-G-82241C Amendm

25、ent-2 Page 11 5.2.3.1 - Delete in its entirety. b.2 - Delete “d“ in its entirety and add the following “ci, When first article inspection is required, the item will be tested and should be a first article sample. The Contracting Officer should include specific instructions in acquisition documents r

26、egarding arrangement for examinati-ons , quantity arid testing and approval e Nien palletization is required (see 5.2.4).“ Page 12 Figure - delete aiid substitute new Figure 1. Custodi-in : Navy - NU Air Force - 99 Re.vic-w Activities : Navy - SH, MC Air Force - 82 DLA - cr User Activities Navy - AS

27、, OS Preparing Activity : Navy - h3-J Project No. 8415-0456 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Amendment-2 A - FIGURE 1. Glove Inserts, Radioactive Contarninants Protective I -.: U.C. GOVERMMENT PRINTING OFFICE: 1985 - 505*038/23257 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-