NAVY MIL-F-51364-1972 FIN ASSEMBLY BOMB 750-LB CLUSTER M14E3《750-LB集束M14E3炸弹装配FIN》.pdf

《NAVY MIL-F-51364-1972 FIN ASSEMBLY BOMB 750-LB CLUSTER M14E3《750-LB集束M14E3炸弹装配FIN》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-F-51364-1972 FIN ASSEMBLY BOMB 750-LB CLUSTER M14E3《750-LB集束M14E3炸弹装配FIN》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、flIL-F-513bq 13 777770b 033373b b mL-F-51364( MU) 6 December 1972 GKsection 6) MILITARY SPECIFICATION FIN, ASSEMBLY, BOMB: 750-LB CLUSTER, M14E3 1. SCOPE 1.1 2. APPLICABLE DOCWNTS This specification covers one type of fin. 2.1 The following documents of the issue in effect on date of invitation for

2、bids or request for proposal, form a part of this specification to the extent specified herein: SPECIFICATIONS FEDERAL PPP-B-636 - Box, Fiberboard. MILITARY MIL-C-11133 - Crate, Wood, Open, Wirebound. STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-1168 - Lo

3、t Numbering of Ammunition. Attributes. DRAWINGS US ARMY MUNITIONS COMMAND EDGEWOOD ARSENAL DL14-23-4082 - Fin Assembly, Bomb : 750-Lb Cluster, Ml4E3. FSC i325 P /- - - I THIS - - I DOCUMENT CONTAINS PAGES A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

4、-,-,-MIL-F-5L364 13 = 7777906 0333737 m MIL-F-51364( MU) (Copies of specifications, standards, drawings and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer. ) 3. REQUIRENENTS

5、 3.1 Materials - components. . All materials cited on Drawing DL14-23-4082 or on the subsidiary drawings shal conform to the specifications listed thereon, or to the specific characteristics set forth. on the drawings. 3.1.2 Componsnts. - All components of the fin shall conform to the spec if icatio

6、ns and drawings listed on Drawing DL14-23-4082 and subsidiary drawings. 3.2 Assembly. The fin shall be assembled as shown on Drawing Elk-23- 4082. 3.3 Tie-rod (Drawinei-23-4087). - The tie-rod brazed joints shall have an effective braze area of not less than 85 percent of the joint area when tested

7、as specified in 4.4.4. 3.4 Preproduction. Prior to the start of regular production, a pre- production sample of fins and tie-rods shall be produced in accordance with this specification for examination and tests (see 4.3). 3.5 Workmanshi . The fin shall be free from foreign matter (oil, grease -? or

8、 dirt and damage such as dents, cracks or deformation which could affect its intended use. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. 4.1.1 Suppliers responsibility. Unless otherwise specified in the contract or purchase order, the supplier is responsible for the perform- anc

9、e of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserv

10、es -the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to specified requirements. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-5136

11、4 13 m 99999b 0333938 T mL-F-51364( MU) 4.1.2 Objective evidence. The supplier shall provide object ive evidence acceptable to the contracting officer that the requirements of 3.1 and section 5 for which specific inspection has not been provided in this specification have been satisfied. 4.2 Classif

12、ication _II- of inspections. The inspection requirements speci- fied herein are classified as follows: (a) Preproduction inspection (see 4.3). (b) Quality conformance inspection (see 4.4). 4.3 Preproduction inspection, 4.3.1 gamjo&eE 11- Critical: None defined AQL 1.0 percent defective Component mis

13、sing Component incorrectly ass embled Fin orientation incorrect Perpendicularity incorrect Spotwelding incorrect Dimension ( 24.47) incorrect Fuze adapter threads incorrect (Drawing Ci4-23-1844 Cone diameter (15-31/32) incorrect (Drawing Brazing incorrect (Drawing D14-23-1831) Frame configuration in

14、correct (Drawing E14-23-1836) Marking incorrect Workmanship ( 3.5 ) AQL 2.5 percent defective C14-23-1352) Fuze fairing location incorrect Protective finish missing Marking illegible Tube guide obstructed (Drawing Bib-23-1535) (b) Tie-rod, body assembly (Drawing D14-23-202O). Defects Categories -_I_

15、 Critical: None defined _- 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.4.3.3 c- Classification of defects (continKed)_. (b) Tie-rod, - bodx-assembly (Drawing D14-23-2020) (ccpkLEuxd)-. Defects - Catsgr-ie- _-.-.- Major: AQL 1.0 percent defect

16、ive 101 Length incorrect 102 Threads incorrect 103 Brazing incorrect 10 4 Workmanship ( 3.5 ) Minor : AQ,L 2.5 percent defective -e- 201 Slot location incorrect Defects _. Categories - Critical : None defined -_I Major: 101 102 103 10 4 105 107 Minor : 201 202 203 204 205 i06 _I- AQL 1. O percent de

17、fective Rivets or bolts missing Dimension (11.519) incorrect Mat er i al incorrect Countersink missing Tack weld missing or inadequate Welding incorrect Workmanship ( 3.5 AQL 2.5 percent defective Pin length incorrect Burrs not removed Dimension ( 4.00 1 incorrect Pin diameter incorrect Dimension (5

18、.12) incorrect (a) - Tie-rod assembly (Drawing Elk-23-4087). - CategoriE Defects Critical: None defined I- rr 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-F-SL3bY I3 777770b 0333743 T MIL-F-S1364(W) 4.4.3 3 -_lit_ Classification of defects_

19、c_ntinued). (d) -I- Tie-rod assembly (Drawing E14-23-4_987) (continued). - Categories -I- Defect s Major: AQL 1.0 percent defective 101 Length incorrect 102 Rivets loose or missing 103 Perpendicularity incorrect 104 105 Workmanship ( 3.5 ) Leg connector to tie-rod braze incorrect Minor : A&L 2.5 per

20、cent defective 201 Protective finish incorrect (e) m, lock&ng-(_Dr_awing Blh-23-40841. Defects L Ca=oxizs- - Critical-: None defined Major: AQL 1.0 percent defective 101 Hole location incorrect 102 Thread 10-32-NF-2 incorrect 103 Thread 3-3/4-12UN-2B incorrect 104 Workmanship ( 3.5 ) Minor : AQL 2.5

21、 percent defective 201 Holes not countersunk 202 Protective finish missina I - I ( f ) Crate, wood, wirebound (Drawing E1417-1503) . Defects _- Cat egor i 5s- Critical : None defined Maj or : _I- A&L 2.5 percent defective 101 Center block members length incorrect or incorrectly ass embled 6 -1 c -.I

22、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-F-5L364 13 m 7777706 0333742 L m mL-F-51364( MU) 4.4.3.3 Classification of defects -l_l_Fd.- (continued). - ( f ) .-.-2-.-L-.-.- Crate wood wirebound (Draw& El4-17-1503) (continued). - -. I-. _.-.-

23、I -. Categories Defects a j or (continued : 102 103 104 105 107 108 109 110 lll i06 MZ: 201 202 203 Positioning pins location incorrect Top assembly overall dimension.incorrect Battens incorrectly located Center block assembly incorrectly located Base assembly overall dimensions incorrect Disc incor

24、rect or incorrectly located Base assembly or top assembly stock size incorrect Blank section spacing or overall dimensions incorrect Blank reinforcing strip location or level incorrect Component missing AQL 4.0 percent defective Strapping incorrect Component loose or damaged Binding wire location in

25、correct (g) Packing, 750-pound cluster fin (Drawing E14-17-923)-. Categories Critical: Major: 101 102 103 104 i05 i06 i Minok : - 20l. Defects None defined AQL 1.0 percent defective Tie-rod not securely wired to frame Fin not located on pins Cap plug missing or incorrectly assembled Blank incorrectly secured Marking incorrect Workmanship ( 3.5 ) AQL 2.5 percent defective Marking illegible i 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-