NAVY MIL-E-17777 D (1)-1987 ELECTRODES CUTTING AND WELDING CARBON-GRAPHITE UNCOATED AND COPPER-COATED《无覆盖物和铜覆盖的碳石墨电极切断和焊接法》.pdf

《NAVY MIL-E-17777 D (1)-1987 ELECTRODES CUTTING AND WELDING CARBON-GRAPHITE UNCOATED AND COPPER-COATED《无覆盖物和铜覆盖的碳石墨电极切断和焊接法》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-E-17777 D (1)-1987 ELECTRODES CUTTING AND WELDING CARBON-GRAPHITE UNCOATED AND COPPER-COATED《无覆盖物和铜覆盖的碳石墨电极切断和焊接法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-E-17777D (1) 311 W 9977906 02451811 5 Cross- section Diameter Circular 1/8, 5/32, 3/16, 1/4, 5/16, 3/8, t Length 12 MIL-E-17777D AMENDMENT 1 24 July 1987 1/2, 5/8, 3/4 1/2, 5/8, 3/4 MILITARY SPECIFICATION t 14 1 ELECTRODES, CUTTING AND WELDING, CARBON-GRAPHITE, UNCOATED AND COPPER-COATED MIL-Cu

2、C-A This amendment forms a part of MIL-E-l7777D, dated 27 February 1984, and is approved for use by all Departments and Agencies of the Depart- ment of Defense. Round copper-coated carbon-graphi te PAGE 1 1/2, 5/8, 3/4 1/2, 5/8, ,3/4 Table I: Delete and substitute: 14 “TABLE I. Types and sizes. Type

3、 1 Description MIL-C Round carbon-graphite (plain-uncoated) I l2 I Circular 1/8, 5/32, 3/16, 1 1/4, 5/16, 3/8, AMSC N/A PSC 3439 DISTRIBUTION STATEMENT A Approved for public release; distribution unlimited 1 of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

4、om IHS-,-,-MIL-E-17777D (1) 34 7979906 0245185 7 MIL-CuC-D MIL-E-17777D AMENDNENT 1 Round copper-coated carbon-graphi te with machined lock-j oint ends Rectangular copper-coated i ca r bo n-g r a p hi t e PAGE 2 Table I: Delete and substitute: “TABLE I. TvDes and sizes. - Continued Circular 5/16, 3/

5、8, 1/2 12 or 14 518, 314, 3/8, 1/2, 5/8, 3/4 17 12 5/32 x 318 - 3/16 x 5/8 TY Pe MIL-CUC-B MIL-CuC-C Cross- Description section Diameter Leng t h Half-round copper-coated 1 Semi- 13/8, 1/2, 518 carbon-graphite circular I l8 t i II 2.1.1: Delete and substitute: “2.1.1 Specifications and standards. Th

6、e following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto,

7、cited in the solicitation.“ PAGE 3 2.1.2: Add after first sentence: “Unless otherwise specified, the issues shall be those in effect on the date of the solicitation.“ 2.1.2: Last line, Delete “contracting officer“ and substitute “contracting activity“. 2.2: Delete and substitute: “2.2 Other publicat

8、ions. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the . issues of do

9、cuments not listed in the DoDISS shall be the issue of the nongovern- ment documents which is current on the date of the solicitation.“ Delete address for National Motor Freight Traffic Association and substitute: “National Motor Freight Traffic Association, Inc., ATA TRAFFIC Dept., 2200 Mill Road,

10、Alexandria, VA 22314.“ 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-E-II7777D (II) 3L1 77777Ob 0245IIBb 7 U I MIL-E-1 7 7 7 7D AMENDMENT 1 PAGE 4 2.2: Delete last paragraph and substitute: “(Nongovernment standards and other publications a

11、re normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational se rvice s . ) “ 2.3: Delete and substitute: “2.3 Order of precedence. In the event of a conflict between the text of thi

12、s specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specifi- cation shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemp

13、tion has been obtained.“ PAGE 5 Add : “4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. absence of any inspection requirem

14、ents in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies sub- mitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective mater

15、ial, either indicated or actual, nor does it commit the Government to acceptance of defective material.“ The PAGE 10 4.7: Delete and substitute: “4.7 Inspection of packaging. Sample packages and packs, and the inspec- tion of the preservation-packaging, packing and marking for shipment and storage s

16、hall be in accordance with the requirements of section 5 and the documents s pec if i ed the rein . “ 5.: Delete and substitute: “(The packaging requirements specified herein apply only for direct Govern- For the extent of applicability of the packaging requirements ment acquisition. of referenced d

17、ocuments listed in section 2, see 6.3.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. . . : -. MIL-E-1 77 77D AMENDMENT 1 PAGE 1.3 6.2.2: Delete and substitute : “6.2.2 Data requirements. 4: kder Custodians: Delete “Army 2 kkrr. Review actfufties: IWvy - PD, MC Mr Force - 99 fYkk A cs uset activity: kriay - AT 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-