NAVY MIL-DTL-82939-2000 SEPARATOR EXPLOSIVE (1W18)《炸药分离器(1W18)》.pdf

《NAVY MIL-DTL-82939-2000 SEPARATOR EXPLOSIVE (1W18)《炸药分离器(1W18)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-82939-2000 SEPARATOR EXPLOSIVE (1W18)《炸药分离器(1W18)》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、= 999990b 2113909 129 MIL-DTL-82939( OS) 11 February 2000 MILITARY SPECIFICATION SEPARATOR, EXPLOSIVE (1W18) This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Departments of Defense. 1. SCO

2、PE 1.1 Scope. This specification covers the requirements for an Explosive Separator (1 W 18), Drawing 838AS220, hereto referred to as separator and its explosive component BBU-55/B explosive bolt, drawing 838AS221. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this specification are s

3、pecified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned t

4、hat they must meet all specified requirments documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein

5、. Unless otherwise specified, the issue of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-1-23659 Initiators, Electrical, G

6、eneral Design Specification for I I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Standardization Team (Code 840M), 101 Strauss A

7、venue, Indian Head, MD 20640-5035, by using the Standardization Document Improvement Proposai (DD Form 1426) appearing at the end of this document or by I sending a letter. AMSC NIA FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Provided by IHSNot for Resa

8、leNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82939(OS j STANDARDS DEPARTMENT OF DEFENSE MIL-STD-1168 Ammunition Lot Numbering and Ammunition Data Card (Unless otherwise indicated, copies of federal and military specifications and standards are available from Standar

9、dization Documents Order Desk, Bldg. 40,700 Robbins Avenue, Philadelphia, PA 191 11-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise

10、specified, the issues are those cited in the solicitation. DRAWINGS Naval Air Systems Command (CAGE Code 30003 j 838AS220 Explosive Separator 83 8AS 22 1 838AS222 ShocWibration Test Fixture Bolt, Explosive, BBU-55/B (Application for copies should be addressed to: Commander, Indian Head Division, Nav

11、al Surface Warfare Center, Attn: Data Control Branch (Code 8410), Indian Head, MD 20640-5035.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those

12、 listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). Holex Dwg. F10369 Rev E Fixture AMERICAN SOCIETY FOR TESTING (2) body, release end down; (3)

13、 horizontal. Use a new separator for each drop. The separators shall not fire when dropped from a height of 6 feet. Each separator shall meet the post-test inspections of Table I and functional performance requirements. 4.4.14 Functional (destructive) tests. One-half of the LAT sample shall be subje

14、cted to functional testing at 165F and the other half at -65F. The temperature conditioning time shall be a minimum of 4 hours after temperature stabilization and a maximum of 24 hours at the respective temperature. The tests at each respective temperature shall be conducted with one-half the sample

15、 at extreme load (see 3.4.4) and the other half with no load present. if the sample is not evenly divisible by four, priority of test conditions shall be at the discretion of Naval Surface Warfare Center, Indian Head, Maryland. The functional test shall be performed in a test fixture (Holex drawing

16、F10369 Rev E) capable of producing a 90,000-pound axial load and a 750-inch-pound torsional load. The bolt or separator shall be functioned by applying 5 amps to either bridgewire. Failure shall result in lot rejection. 4.4.14.1 Test failure. If a test failure is attributable to an assignable cause,

17、 excluding the test bolt or separator, the original test results shall be discarded and the test reconducted. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of material is to be performe

18、d by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Depa

19、rtments System Command. Packaging data retrieval is available from the managing Military Departments or Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

20、m IHS-,-,-6. NOTES (This section contains information of a general or explanatory nature that may be helpful but is not mandatory.) 6.1 Intended use. The separator is used to release any load from the CH-53E or MH-53E Helicopter Single Point Cargo Hook in the event of an emergency. As the separator

21、is designed for use only with cargo hooks on military helicopters, it has no commercial application. 6.2 Acquisition requirements. Acquisition documents must specify the following: a. Title, number, and revision letter of this specification. b. Issue of DODISS to be cited in the solicitation and, if

22、 required, the specific issue of individual documents referenced (see 2.2.1, 2.2.2 and 2.3). c. Whether a first article sample is required and, if so, the test activity (see 3.1 and 4.2). d. Production lot size and test activity (see 4.3.3.1). e. Directions for shipping: radiographs of explosive bol

23、ts, the entire production lot of separators, along with ballistic sample to the activity conducting production lot acceptance tests. f. Items of data required for each first article and production lot, including explosive bolt test data and marriage log to separators. g. Packaging requirements. h. A

24、mmunition data cards in accordance with MIL-STD-1168. i. Submission of rework procedures, acceptance test and inspection procedures, and explosive bolt acceptance test and inspection results. j. That the safety precaution requirements of the “Contractors Safety Manual for Ammunition, Explosives, and

25、 Related Dangerous Material,” DOD 4145.26M are applicable. NOTE: When this specification is used as part of the description of work to be accomplished by a Government activity, the safety precaution requirements of Ammunition and Explosives Ashore,” OP 5 are applicable. 6.3 First article. When a fir

26、st article inspection is required, the contracting officer should provide specific guidance to offerors whether the items should be a first article sample or a sample selected from the first production items (see 3.1), and the number of items to be tested as specified in 4.2. The contracting officer

27、 should also include specific instructions in acquisition documents regarding arrangements for examination, approval of first article test results, and disposition of first articles. Invitations for bids should provide that the Government reserves the right to waive the requirement for samples for f

28、irst article inspection to those bidders offering a product which has been previously acquired or tested by the Government, and that bidders offering such products, who wish to rely on such production or test, must furnish evidence with the bid that prior Government approval is presently 11 Provided

29、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-appropriate for the pending contract. Bidders should nor submit alternate bids unless specifically requested to do so in the solicitation. 6.4 Loaded assembly hazard information. DOD, DOT, NATO Hazard Classific

30、ation United Nations Serial Number 0173 DOD Markings Explosive Separator Class 1, Division 4 Storage Compatibility Grouping S 6.5 Definitions. 6.5.1 Stabilized. A stabilized separator is the same temperature throughout. 6.6 Subject term (keyword) listing. Explosives Helicopter Separator Preparing ac

31、tivity Navy - OS (Project 1377-01 03) 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Normal to the longltudlnal A * Longitudinal I FIGURE I. Separator, Explosive (1 W18), Definition of Axes 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-