NAVY MIL-DTL-24640 16 E-2011 CABLE ELECTRIC -20 TO +105 癈 600 VOLTS LIGHTWEIGHT MULTI-PAIR 18 AWG TYPE 2XSW (INCLUDING VARIATION TYPE 2XSOW)《2XSW型18 AWG多对轻量600V -20 ℃~+105 ℃电缆(包括变化型2XSOW)》.pdf

《NAVY MIL-DTL-24640 16 E-2011 CABLE ELECTRIC -20 TO +105 癈 600 VOLTS LIGHTWEIGHT MULTI-PAIR 18 AWG TYPE 2XSW (INCLUDING VARIATION TYPE 2XSOW)《2XSW型18 AWG多对轻量600V -20 ℃~+105 ℃电缆(包括变化型2XSOW)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-24640 16 E-2011 CABLE ELECTRIC -20 TO +105 癈 600 VOLTS LIGHTWEIGHT MULTI-PAIR 18 AWG TYPE 2XSW (INCLUDING VARIATION TYPE 2XSOW)《2XSW型18 AWG多对轻量600V -20 ℃~+105 ℃电缆(包括变化型2XSOW)》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 6145 INCH-POUND MIL-DTL-24640/16E 8 November 2011 SUPERSEDING MIL-DTL-24640/16D 22 August 2002 DETAIL SPECIFICATION SHEET CABLE, ELECTRIC, -20 TO +105 C, 600 VOLTS, LIGHTWEIGHT, MULTI-PAIR, 18 AWG, TYPE 2XSW (INCLUDING VARIATION TYPE 2XSOW) This specification is approved for use by all

2、Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24640. Construction (Watertight) First - Tin-coated copper conductor in accordance with table I. Second - Insulation material and b

3、asic construction requirements shall be in accordance with SAE-AS81044/12 and tested in accordance with the component wire ratings and requirements listed on this specification sheet. Conformance testing shall be in accordance with SAE-AS81044 prior to cabling. Third - Two conductors, one black and

4、one white, twisted together. The pitch shall be 1 inch. Fourth - Optional binder tape. Fifth - Braided shield of 38 AWG tin-coated copper strands. Braid coverage shall be no less than 90 percent determined in accordance with WC-27500. Sixth - Shield insulation of two polyester tapes or polyester tap

5、e and extruded jacket. Identification codes applied using Method 2. (NOTE: This step is not required for Type 2XSW1.) Seventh - The required number of shielded, twisted pairs shall be cabled together. Cabling sequence shall be consecutive, starting with number 1 from center outward. Fillers may be u

6、sed, as necessary, to form a round cable. Eighth - Optional binder tape. Construction Variant for Type 2XSW Ninth - Cross-linked polyolefin jacket (see table II for thickness). NOTE: Manufacturers identification tape or thread is required (see 3.7.3). Construction Variant for Type 2XSOW Ninth - Brai

7、ded shield, tin-coated copper strands. Braid must be constructed to meet surface transfer impedance requirements as listed herein. Tenth - Optional binder tape. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24640/16E 2 Eleventh - Cross-link

8、ed polyolefin jacket (see table III for thickness). NOTE: Manufacturers identification tape or thread is required (see 3.7.3). TABLE I. Component wire details. Watertight conductor Finished wire Wire size (AWG) Stranding (no. x AWG) Test load life cycle accelerated aging tests (lbs 3%) Low temp. at

9、-40 C Mandrel diameter (inches) Test load (lbs) 18 7 x 26 0.250 1.0 1.0 TABLE II. Construction details. PIN M24640/16 Type number Number of pairs Jacket thickness (inch) (min.) Cable diameter (inch) Cable weight (pounds per 1000 feet) (max.) (min.) (max.) -01UN -02UN -03UN 2XSW-1 2XSW-3 2XSW-7 1 3 7

10、 0.034 0.041 0.044 0.240 0.436 0.573 0.258 0.470 0.617 52.9 175.0 330.0 TABLE III. Construction details - overall shield. PIN M24640/16 Type number Number of pairs Jacket thickness (inch) (min.) Cable diameter (inch) Cable weight (pounds per 1000 feet) (max.) (min.) (max.) -01UO -02UO -03UO -04UO -0

11、5UO 2XSOW-3 2XSOW-7 2XSOW-12 2XSOW-19 2XSOW-30 3 7 12 19 30 0.041 0.044 0.047 0.050 0.057 0.487 0.608 0.802 0.938 1.180 0.525 0.656 0.864 1.010 1.270 227.0 401.0 665.0 950.0 1442.0 REQUIREMENTS: Qualification required. Construction details: See tables I, II, and III. Component wire: The component wi

12、re shall be in accordance with SAE-AS81044 and shall be tested in accordance with the following wire ratings and additional requirements. Temperature rating 135 C (275 F) (max.) conductor temperature Voltage rating 600 volts (root mean square) at sea level Accelerated aging Oven temperature, 2502 C

13、(4823.6 F) for 6 hours Low temp. cold bend -40 C (-40 F) for 4 hours Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24640/16E 3 Blocking 1502 C (3023.6 F) Color In accordance with MIL-STD-104, Class 1; white preferred Flammability 30 seconds

14、 (max.) 3.0 inches (max.) No flaming of tissue paper Humidity resistance 5000 megohms for 1000 feet (min.) insulation resistance after humidity exposure Dielectric test Primary insulation 6.0 kilovolts (peak), 100 percent impulse test (when tested in lieu of spark test) Finished wire 8.0 kilovolts (

15、peak), or 3 kHz spark test 5.5 kV, 100 percent test Insulation resistance 5000 megohms for 1000 feet (min.) Life cycle Oven temperature, 2002 C (3923.6 F) for 120 hours Physical properties of primary insulation Tensile strength 2500 lb/in2(min.) Elongation 150 percent (min.) Shrinkage 0.125 inch (ma

16、x.) at 2502 C (4822 F) Spark test primary insulation 1500 volts (root mean square), 3 kHz, 100 percent test Surface resistance 500 megohms inches (min.), initial and final readings Thermal shock Oven temperature, 1502 C (3023.6 F) Maximum change in measurement 0.060 inch Wet dielectric test 2500 vol

17、ts (root mean square) Wrap test Mandrel wrap test required INSPECTION: Basic Electricals: Conductor resistance (ohms/1000 feet at 25 C, max.) 7.11 Voltage withstand (volts, root mean square, min.) Conductor to conductor and shield 1000 Component shield to component shield 200 Component shield to ove

18、rall shield (Type 2XSOW only) 500 Insulation resistance (megohms/1000 feet, min.) Conductor to conductor and shield 2500 Shield to shield (component shield only) 100 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24640/16E 4 Shield to shield

19、 100 (component shield to overall shield, Type 2XSOW only) Conductor and shield continuity No failure Jacket flaws (Type 2XSOW only) No failure Group A: Visual and dimensional No failure Capacitance Mutual capacitance (at 1 MHz, picofarads/foot (pF/ft), max.) 60 Capacitance unbalance (percent, max.)

20、 15 Characteristic impedance (at 1 MHz, ohms) 30 (min.), 53 (max.) Watertightness No failure (see table IX of MIL-DTL-24640 for limits of water leakage) Weight No failureGroup B: Cold bending No failure Drip No failureCross-link proof test (percent, max.) Jacket 50 Tear (lb/in thickness, min.) 35 Ph

21、ysicals (unaged) Jacket Tensile strength (lb/in2, min.) 1300 Elongation (percent, min.) 160 Attenuation (at 3 MHz, dB/100 feet, max.) Not applicable Gas flame (1 hour) Not applicable Group C: Physicals (aged), air oven Jacket Tensile strength (percent of unaged, min.) 60 Elongation (percent of unage

22、d, min.) 60 Permanence of printing (conductor insulation, cycles, min.) Not applicable Permanence of printing (jacket, cycles, min.) 125 Heat distortion (percent of unaged, max.) 30 Cable sealant removability No failure Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

23、ense from IHS-,-,-MIL-DTL-24640/16E 5 Shrinkage No failure Surface transfer impedance (Type 2XSOW only) Milliohms per meter (max.) 700 EMP response (dB, min.) 60 Group D: Flame propagation No failure Qualification Inspection: Qualification inspection shall include basic electricals; groups A, B, C,

24、and D; plus the following: Aging and compatibility (cable) No failure Acid gas equivalent (percent, max.) Jacket 2 Fillers 2 Insulation 18 Halogen content (percent, max.) Jacket 0.2 Fillers 0.2 Immersion (jacket) Tensile strength (percent of unaged, min.) 50 Elongation (percent of unaged, min.) 50 S

25、moke index (max.) Jacket 25 Fillers 45Insulation 10Toxicity index (max.) Jacket 5 Fillers 5 Insulation 1.Durometer (jacket) - Type A (hardness, min.) 80 Weathering (jacket) No failure Fungus resistance No failure Abrasion resistance No failure Gas flame (3 hour) Not applicable Component wire No fail

26、ure Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24640/16E 6 UNIT ORDERING LENGTHS: Type and size Feet (nominal) 2XSW-1, 2XSW-3, 2XSW-7, 2XSOW-3, 2XSOW-7, 2XSOW-12, 2XSOW-19, 2XSOW-30 3 - 12 500 feet nominal 19 & 30 250 feet nominal CHANGE

27、S FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity:Army MI Navy SH Navy SH (Project 6145-2009-084) Review Activities: Army AR, AV, CR, CR4 Navy CG, EC DLA CC N

28、OTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-