NAVY MIL-DTL-24231 25 E-2013 CONNECTOR HULL INSERTS TYPE VII.pdf

《NAVY MIL-DTL-24231 25 E-2013 CONNECTOR HULL INSERTS TYPE VII.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-24231 25 E-2013 CONNECTOR HULL INSERTS TYPE VII.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/25E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/25D(SH) w/AMENDMENT 1 2 April 1993 MIL-C-24231/25D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, HULL INSERTS, TYPE VII This specification is approved for use by the Naval Sea Systems Command and is avai

2、lable for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Hull inserts are not furnished as part of cable connector assemblies. Acquisition of h

3、ull inserts is the responsibility of the installing activity. Assurance that the hull insert adequately compensates for holes in submarine pressure hulls is the responsibility of the installing activity. 2. Inserts shall be made of a material compatible with the applicable hull. Hull inserts shall b

4、e manufactured from steel as follows: a. For HY-80 steel hulls, steel grade HY-80 of T9074-BD-GIB-010/300 shall be used. The ends of inserts shall be stamped with identification symbol “HY-80” in -inch high letters. Welding and inspection of the hull inserts shall be in accordance with T9074-AD-GIB-

5、010/1688. b. Ordinary strength steel hulls shall use Grade A or B of the American Bureau of Shipping (ABS) Rules for Building and Classing Steel Vessels, Part 2, Section 1 (with the supplementary requirements in Appendix 2/D). Higher strength steel hulls shall use EH-36 or the ABS Rules. 3. Internal

6、 dimensions, height dimensions, pin dowel dimensions, and the location shall be provided. 4. Nickel copper cladding indicated for gasket seat shall be provided. 5. All dimensions are in inches. 6. Tolerances shall be as follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c. Angular

7、 dimensions degree. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/25E(SH) 2 FIGURE 1. Connector, hull inserts typical. HOLE DRIL LEDTO SUIT PINABASS EMBLY HUL L INSER TSM24231/25 -0 01M24231/25 -0 02M24231/25 -0 03140.270116X 45 CHAMF

8、 ERPIN, DOWELFEC4545D0.27018GASK ET SEA T INSERT WELD OFNICKEL-COPP ER (BOTH END S)TABLE O F DIMENS IONSM24231/25 -0 01 M24231/25 -0 02 M24231/25 -0 03AB-DIAC-DIAD-DIAEF2.7504342.0201.7704.5002.2503.3755122.6452.3955.0002.5004.50063.6253.2704.7501.7504ALL OVEREXCEPTAS SHOWN1251326363FIGUR E 1. Con n

9、 ector, hu ll inse rts - t ypical .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/25E(SH) 3 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/25- 3/ Material/specification Remarks 001 002 003 1 Insert, hull 1 - See fi

10、gure 1. 2 Insert, hull 1 - See figure 1. 3 Insert, hull 1 - See figure 1. 4 Pin, dowel, diameter by length 2 2 2 Driv-lok, Type D, CRES, coml, Type 316 passivated, or equal See figure 1. NOTES: 1/ Item numbers are the same as encircled numbers shown on figure. 2/ See applicable figure or table liste

11、d in remarks column for part numbers and dimensions. 3/ Quantity is for one complete assembly of each size. CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Navy

12、SH (Project 5935-2011-074) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-