NAVY MIL-DTL-24231 15 E-2013 CONNECTOR ADAPTER FOR MOLDED PLUG TYPE II THREE- AND FOUR-CONDUCTOR.pdf

《NAVY MIL-DTL-24231 15 E-2013 CONNECTOR ADAPTER FOR MOLDED PLUG TYPE II THREE- AND FOUR-CONDUCTOR.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-24231 15 E-2013 CONNECTOR ADAPTER FOR MOLDED PLUG TYPE II THREE- AND FOUR-CONDUCTOR.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/15E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/15D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, ADAPTER, FOR MOLDED PLUG, TYPE II, THREE- AND FOUR-CONDUCTOR This specification is approved for use by the Naval Sea Systems Command and is available for

2、 use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 6. 2. Material for adapter body shall be ma

3、nufactured from nickel-copper alloy in accordance with Class A, Form 1, hot-finished condition of QQ-N-281 with a minimum yield strength of 40,000 lbf/in2 at 0.2 percent offset, or nickel-copper alloy in accordance with Class A, Form 1, cold-drawn condition of QQ-N-281 with a minimum yield strength

4、of 50,000 lbf/in2 at 0.2 percent offset. 3. All dimensions are in inches. 4. Tolerances shall be as follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI

5、L-DTL-24231/15E(SH) 2 FIGURE 1. Connector, adapter typical. FIGURE 1. CO NN ECTO R, A DAP TER - T YP ICA L .NYLON INSERT 0 .1 25X 0 .203 LG (2 REQ D)ASSY , INSERT MOL DE DM2423 1/15-0 20 O RM24 2 31 /15-03 0FLANGE 114I N.HIGH IMPAC T PV CM24 2 31 /15-04 0DRILL 0.09 4 HOL E ATASSY FOR SPR INGPI NSPRI

6、NG PIN, CRESNAS M17 1 50 2SCREW, RH 0 .164 -3 2N C-2 AX 38LG, M2 4231 /15-04 3ASSE MBLY, CA PM24 2 31 /15-04 0MONE L PIN 0 .083L ENG TH TO S UI TGASK ET, O-RINGSAE-AS 2 8775- 11 5ASSY ADPTR BO DYM24 2 31 /15-01 0RETAINING RING,M2423 1/5- 07 3GASK ET, O-RING (2REQD) SA E-AS287 75 -21 5CAP, M242 31/12

7、 -01 1MOUNTING DIMENSION SMOUNTING BOLT S 12-1318278911143121319154561713 COND , M24 231/15 -0 01 SYM . 1 11 54 COND , M24 231/15- 00 2312ADAP TER ASSE MB LYCHAIN, SAFET Y, - 5“ LO NGM24 2 31 /15-04 2SCREW, RH 0 .164 -3 2N C-2 AX 12LG, M2 4231 /15-04 1Provided by IHSNot for ResaleNo reproduction or

8、networking permitted without license from IHS-,-,-MIL-DTL-24231/15E(SH) 3 FIGURE 2. Assembly, adapter body M24231/15-010. R , POL AR I ZI NGGROOVE301764132R3160.50 00.43 7FIGU RE 2. A SSE MBL Y, AD A PTE R B ODY - M24231 /15-01030.34 40.34 40.43 70.50 0PIN 0.092332H OLEW ELD1.87 5-1 2U N-2 AU NDERCU

9、 T11116-12 U N -2A (T YP)29320.78 10.06 42.53 2132R30300.04 62 H OLE S 0 .12 00.18 7 D EE P. DON OT PEN ETR ATE.32183160.04 7 R , GR OO VE125AL L OV ER EXCEPTAS SH OWN0.05 20.05 0R , POL AR I ZI NGGROOVE0.05 20.05 00.87 60.87 20.98 90.97 90.89 60.88 61.09 21.08 81.30 21.29 83.44 33.43 37323273218316

10、32+0 .000-0.00 50.02 70.02 30.72 40.71 40.06 20.89 60.88 60.63 00.62 03 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/15E(SH) 4 FIGURE 3. Flange M24231/15-040. FIGURE 4. Assembly, cap M24231/15-040. 90.164-32N C- 2 BPA D, 12 X 14 , NI

11、 -A L- BR ZCA P ,M2423 1/1 2 - 0 1 11819FIG URE 4. ASSEMBLY, CAP - M24 23 1/ 15 -0 40 .10FIG URE 3. FLANGE - M2423 1/ 15 -04 0 .STAMP OR ENGRAVEAS SHOWN AN D FIL LWITH W H I TE ENAM EL645 312916D R I L L(4 HOLES)1.875-12UN- 2 B0.164-32NC- 2 B1 H OLE 12DEEP58REF78REF458REF1342M2/15-0402516REF6 9 Prov

12、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/15E(SH) 5 FIGURE 5. Assembly, insert, molded M24231/15-030 (4-conductor). 1324CL0.2 19 (TYP)CL16INS ERTMOLDE D EPOXYRES IN20WIRE 21S OLDER0.2 19(TY P)2413CLCL0.2 19(TY P)NO T E : M2 42 31 /15

13、-030 SIM IL AR TOM242 31/1 5-020 EXCEPT A S SHO WN .FIGU RE 5. AS SE MBLY , INS ER T, MOLDED - M 24 23 1/ 15 -0 30 .50.2 19(TY P)E ACH P IN SH ALL BECON NECT ED T O I TSMAT CHING PI N NO.ON OPP OS ITE E ND.P IN, CONTACT(8 R EQD)(4-CONDUC TOR)5 Provided by IHSNot for ResaleNo reproduction or networki

14、ng permitted without license from IHS-,-,-MIL-DTL-24231/15E(SH) 6 FIGURE 6. Assembly, insert, molded M24231/15-020 (3-conductor). 1234(3-CONDUC TOR)1230.0 770.1 56CL0.1 350 .6250.7 140.7 100.0 55RMOLD IN P INNUMBE RS ONE ACH E ND.0.0 770.1 56CL0.1 350 .860 0.6 100.6 00P IN, CONTACT(6 R EQD)160.1 87F

15、IGU RE 6. AS SE MBLY , INS ER T, MOLDED - M 24 23 1/ 15 -0 20 .38164R2.0 000.0 539641332INS ERTS OLDERWIRE21716MOLDE D EPOXYRES IN20E ACH P IN SH ALL BECON NECT ED T O I TSMAT CHING PI N NO.ON OPP OS ITE E ND.4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

16、 IHS-,-,-MIL-DTL-24231/15E(SH) 7 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/15- 3/ Material/specification Remarks 001 002 1 Connector, adapter, 3-conductor, symbol no. 1115 1 - See figure 1. 2 Connector, adapter, 4-conductor 1 - See figure 1. 3 Body, adapter 1 1 Ni-Cu, Class

17、 A, QQ-N-281 See figure 2 and requirement 2. 4 Insert assembly, molded 3-conductor 1 See items 16, 20, and 21. See figure 6. 5 Insert assembly, molded 4-conductor 1 See items 16, 20, and 21. See figure 5. 6 Flange, 1 inch 1 1 High impact PVC, coml See figure 3. 7 Chain, safety, 5 inch long 1 1 Brass

18、, coml 4/ See figure 1. 8 Screw, roundhead 0.164-32NC-2A by long 1 1 Brass, coml See figure 1. 9 Cap, pressure-proof 1 1 M24231/12-011, modified as shown 5/ See figure 4. 10 Pad, diameter by long 1 1 Ni-Al-BRZ, ASTM B150/B150M See figure 4. 11 Pin, guide 1 1 M24231/12-012 See figure 1. 12 Gasket, O-

19、ring 1 1 SAE-AS28775-115 6/ Lubricate with silicone compound, SAE-AS8660; see figure 1. 13 Gasket, O-ring 2 2 SAE-AS28775-215 6/ See item 12. 14 Ring, retaining 1 1 M24231/5-073 See figure 1. 15 Insert 2 2 M24231/5-077 See figure 1. 16 Pin, contact 6 8 MIL-DTL-24231 See figure 5 and figure 6. 17 Pin

20、, spring 1 1 CRES, NASM 171502 See figure 1. 18 Screw, roundhead, RH 0.164-32NC-2A by 38 long 1 1 Brass, coml See figure 1. 19 Cap, assembly 1 1 M24231/12-011 5/ See figure 1. 20 Epoxy resin, molded As required Cast epoxy resin compound 7/ See figure 5 and figure 6. 21 Wire As required Type B-16, SA

21、E-AS22759/11 See figure 5 and figure 6. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/15E(SH) 8 TABLE I. Parts list Continued. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or tabl

22、e listed in remarks column for part numbers and dimensions. 3/ Quantity is for one complete assembly of each size. 4/ Safety chains shall be coated with gray plastisol or covered with sleeving in accordance with MIL-I-631 (size number 1, 0.294 id, Subform Ua, Grade a, Class II, Category 1, color whi

23、te) for noise reduction. 5/ Cap material shall be Ni-Al-BRZ, ASTM B150/B150M. 6/ Nitrile (Buna N); Parker Hannifin Corporation (part number N0756-75), O-ring Division, 2360 Palumbo Drive, Lexington, KY 40509, CAGE 02697, or equal. 7/ Arco Set 200, M.M. Reif and Co., Ivyland, PA, or PR610- TCF (Chock

24、fast Orange), ITW Philadelphia Resins Corp., Montgomeryville, PA, or equal. CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Navy SH (Project 5935-2011-064) NOTE:

25、 The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-