NAVY MIL-C-87014 B-1990 CAP GARRISON WOMAN-S (COAST GUARD)《女式军便帽海岸巡逻队队员)》.pdf

《NAVY MIL-C-87014 B-1990 CAP GARRISON WOMAN-S (COAST GUARD)《女式军便帽海岸巡逻队队员)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-87014 B-1990 CAP GARRISON WOMAN-S (COAST GUARD)《女式军便帽海岸巡逻队队员)》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、PlIL-C-870L4B 4 W 777770h 0433723 7 W MIL-C-87014B(CG) 21 YAY 1990 SUPERSEDING MIL-C-87014A(CG) 2 February 1982 IILIT RY SPECIFICATION CAP, GARRISON, WOMANS (COAST GUARD) * This specification is approved for use by the United States Coast Guard and is available for use by the Department of Transport

2、ation. 1. SCOPE * 1.1 Scope. This specification covers the requirements for a polyester and wool garrison type cap. 1.2 Classification. The garrison type cap shall be of one type only, and shall be procured in the following sizes as specified (see 6.2): Schedule of Sizes 20, 20-1/2, 21, 21-1/2, 22,

3、22-1/2, 23, 23-1/2 and 24 2. APPLICABLE DOCUMENTS * 2.1 Government documents. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 S

4、trathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A, Approved for public release; distribution is unlimited. Provided by IHSNot fo

5、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-87014B 4 W 7777706 0433724 7 W MIL-C-87014B(CG) iI * 2.1.1 Specifications,. standards, and handbooks. The following specifications, standards and handbooks form a part of this document to the extent specified herein.

6、Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL , * NN-P-71 CCC-C-476 DDD-L-20 MILITARY * MIL-C

7、-368 * MIL-C-823 * MIL-P-15011 * MIL-B-17757 MIL-T-43548 MIL-C-44121 STANDARDS FEDERAL * FED-STD-191 . FED-STD-751 MILITARY * MIL-STD-105 MIL-STD-129 * MIL-STD-147 - Pallet, Material Handling, Wood, Stringer Construction, 2 Way and 4 Way (Partial) - Cloth, Bunting, Nylon, and Nylon and Wool - Label,

8、 for Clothing, Equipage, and Tentage (General Use) - Cloth, Satin, Rayon and Cloth, Twill, Rayon - Cloth, Serge, Wool, Wool and Nylon, Polyester,and - Pallet, Material Handling, Wood, Post Construction,. - Box, Shipping, Fiberboard (Modular Sizes) - Thread, Polyester Core: Cotton-, Rayon-, or Polyes

9、ter-covered - Cloth, Twill, Polyester Wool 4 Way Entry - Textile Test Methods - Stitches, Seams, and Stitchings - Sampling Procedures and Tables for Inspection By - Marking for Shipment and Storage - Palletized Unit Loads Attributes * MIL-STD-2073-1 - DOD Material Procedures For Development Measurem

10、ent shall be taken across the width of the top crown (gusset) piece at center of cap, folded edge to folded edge. F. Measurement shall be taken from folded edge straight across and parallel to top of cap, to the opposite folded edge then doubled. 3.9 Workmanship. The finished caps shall conform to t

11、he quality of product established by this specification. The occurrence of defects shall not exceed the applicable classification specified in Table IV. 4. QUALITY ASSURANCE PROVISIONS * 4.1 Responsibi1,ity for inspection. Unless otherwise specified in the contract or purchase order, the contractor

12、is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for performance of the inspection requirements specified he

13、rein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. * 4.1.1 Responsibility for compliance. All it

14、ems must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibili

15、ty of ensuring that all products or supplies submitted to the Government for .acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is acceptable practice to ascertain conformance to requirements, however, this does not authorize submissio

16、n of known defective material, either indicated or actual, nor does it commit the government to acceptance of defective material. 4.1.2 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of t

17、he certification. 4.2 Classification of inspection. The inspection requirements specified herein are classified as follows: 1. First article inspection (see 4.3). 2. Quality conformance inspection (see 4.4). * 4.3 First article inspection. When required, the first article s.ubmitted in accordance wi

18、th 3.2, shall be inspected as specified in 4.4.2 for compliance with design, construction, workmanship, appearance and dimensional requirements. 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-70L4B 4 777770b 0433735 3 M * 4.4 Quality confor

19、mance inspection. Sampling for inspection shall be performed in accordance with MIL-STD-105, except where otherwise indicated. * 4.4.1 Component and material inspection. In accordance with 4.1 above, components and materials shall be tested in accordance with all the reqhrements of referenced specif

20、ications, drawings, and standards unless otherwise excluded, amended, modified, or qualified in this specification or applicable procurement documents. Components and materials shall be tested for the characteristics specified in accordance with the referenced test methods of FED-STD-191 whenever ap

21、plicable. The lot size for the requirement listed in Table III shall be expressed in units of yards and the sample unit shall be 1/4 yard full width. All. test reports shall contain the individual values used in expressing the final report result. The lot for the cloth, bunting nylon shall be unacce

22、ptable if one or more units fail to meet the test requirement specified. The sample size for testing the cloth, bunting, nylon shall be as follows: Sample size 800 or less 801 up to and including 22,000 22,001 and over * Table III - Testing of components 2 3 5 Component Characteristics Requirement T

23、est Paragraph Me t hod Cloth, bunting , Colorfastness to nylon wet-dry cleaning 3.3.2 5622 4.4.2 Examination of the end item. The defects found during the examination of the fully assembled garrison cap shall. be classified in accordance with 4.4.2.1 and 4.4.2.2. The applicable inspection levels and

24、 acceptable quality levels (AQLs) shall be as indicated in 4.4.2.3. The lot size shall be expressed in terms of the sample unit. The sample unit shall be one finished cap. * 4.4.2.1 Visual examination. 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

25、-,-_ MIL-C-87OLYB 84 W 77777Ob 043373b 5 W Defect MIL-C-87014B(CG) Table IV - Classification of Defects Classification Major Minor AB I Material Defects and WorkmanshiD Damages a. Any hole, cut, tear, smash, mend, needle chew, drill hole or open place: 1, On outside (longest dimension in any directi

26、on): (a) up to 1/4 inch, inclusive (b) more than 1/4 inch 2. On inside (longest dimension in any direction): (a) up to 1/4 inch, inclusive (b) more than 1/4 inch b. Loose yarn, snagged yarn, misweave, float, coarse yarn, area of no dye penetration, dye streak, missing yarn, broken yarn, thin place,

27、shade bar or woven in waste: 1. On outside (longest dimension in any direction): (a) up to 114 inch, inclusive (b) more than 1/4 inch c. Permanent fold, pleat or crease in cloth (when caught in seaming or stitching): 1. On outside d. Knot or slub on outside - 1/ - 1/ In accordance with basic materia

28、l requirements II Shaded parts a. On outside: 1. Any part shaded or variation in shade within a part III Pressing a. Burned or scorched b. Blocking or pressing omitted X X X X X X X X X X X 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-701

29、4B BL( 777770b Oq33737 7 M Table IV - Classification of Defects (contd) Classification Major Minor Defect AB III Pressing (coil t d) c. Pressing impression or gloss on outside of cap X d. Bottom edge of cap not pressed as specified X IV Cleanness a. Any spot or stain visible at three feet: 1. On out

30、side (longest dimension in any direction): (a) up to 1/4 inch (b) more than 1/4 inch 2. On inside b. Any marking exposed or visible on outside c. Thread ends: 1. On outside: (a) more than one but not more than three not trimmed to less than 3/8 inch (b) more than three not trimmed to less than 3/8 i

31、nch (c) three or more loose threads not removed 2. On inside: (a) three or more thread ends not trimmed to less than 1/4 inch d. One or more shade or size tickets not removed e. Visible basting thread not removed f. Thread end caught for a distance of more than 1/4 inch in line of stitching on outsi

32、de V Component and Assembly a. Any component part or operation omitted (unless otherwise classified herein) X X X X X X X x X 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-870L4B 84 9999906 0433738 9 9 Table IV - Classification of Defects

33、(contd) CPassi f ica t ion Major Minor Defect -3 V Component and Assembly (contd) b. Any component not as specified c. Any component part tight, twisted, distorted, pleated full (unless otherwise classified herein) d. Any operation not as specified (unless otherwise classified herein) VI Cutting a.

34、Any component part not cut in accordance with specified pattern, directional lines on patterns, or not in accordance with specification requirements b. Twill line of any outside part not running in specified direction VI1 Seams and Stitching a. Accuracy of seaming: 1. Seam puckered (score only when

35、on major portion of seam) 2. Seam irregular, pleated or wavy 3. Part caught in any unrelated operation or stitching 4. End of stitching when not caught in another seam or stitching backtacked less than 1/4 inch, or end of continous overlapped less than 1/2 inch 5. Stitching overlapping end of thread

36、 break less than 1/2 inch 6. Not specified color or varying shades of thread used on outside 7. Optional basting or holding stitching visible on outside of cap b. Gage of stitching and seam allowance: 1. Edge, top or raised stitching sewn too close to edge resulting in damage to cloth 16 X X X X X X

37、 X X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-870148 AL( 777770b 0433737 O Table IV - Classification of Defects (contd) Classification Major Minor AB Defect VI1 Seams and Stitching (contd) 2. Seam allowance not as specified by 1/16 inc

38、h or more. (Score only when condition exists on more than 1/2 the length of the seam) 3. Irregular or not within range specified or varies mre than 1/16 inch when no range is specified (score only when condition exists on more than 1/2 the length of the seam) c. Open seam: 1. more than 1/4 inch 2. m

39、ore than 1/4 inch up to 1/2 inch inclusive X X X X 3. up to 1/4 inch inclusive d. Raw edge: 1. On outside: (a) up to 1/4 inch inclusive (b) more than 1/4 inch up to 3/4 inch inclusive (c) more than 3/4 inch 2. On inside: (a) 1/4 inch up to 1/2 inch inclusive (b) more than 1/2 inch up to and includin

40、g one (c) more than 1 inch inch e. Seam and stitch type: 1. Not specified seam or stitch type 2. Any line of stitching omitted 3. Any line of stitching not beginning or ending where specified (unless otherwise classified herein) 4. Looper thread of 401 stitch type on outside X X X X X X X X X X X 17

41、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-87024B 84 9 777790b 04337LIO 7 M MIL-C-87014B(CG) Table IV - Classification of Defects (contd) Classification Major Minor Defect AB VI1 Seams and stitching (contd) f. Stitch tension: 1. Loose ten

42、sion resulting in a loose seam 2. Loosely exposed loops of lower or top thread on edge of top or raise stitching 3. Tight tension (stitches break when normal strain is applied in the direction of the seam or stitching) g. Stitches per inch (score only when condition 1. more than the maximum specifie

43、d exists on more than 112 the length of seam): 2. less than the minimum specified (a) by one or two stitches (b) by three or more stitches h. Runoff skipped or broken stitch: 1. Joining seam - use open seam classification 2. Edge, top or raised stitching: (a) up to 1/2 inch inclusive (b) more than 1

44、/2 inch VI11 Sweatband (Bias Band) a. Omitted b. Short or tight, causing puckering, gath pleats on apron c. Finished width not as specified ri d. Seamed end of sweatband not turned under and stitched to crown side e. Sweatband not of uniform width along major portion of sweatband X X X X X X X X 18

45、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-87034B 84 m 7977706 0433743 7 m Table IV - Classification of Defects (contd) Classification Major Minor Def ec t AB VI11 Sweatband (Bias Band) (contd) f. Lower edge of sweatband exposed beyond rol

46、led edge g. Lower edge of sweatband not positioned above bottom of apron rolled edge. of apron as specified h. Folded end of band not on right or left side and more than 3 inches from back of cap i. More than one splice j. Raw edges of splice on outside of sweatband k; Splice not sewn diagonally IX

47、Top Crown (Gusset) a. Width less than or more than specified b. Gusset seam offset from center: 1. 1/8 inch to 1/4 inch inclusive 2. more than 1/4 inch c. Twisted, poorly shaped, tight, puckered or poorly constructed at joining to the side crown X X X X X X d. Depth of tuck less than 3/16 inch or mo

48、re than 1/4 inch deep front: e, Crease line at center of crown not aligned with center 1. 1/8 inch to 1/4 inch inclusive 2. more than 1/4 inch X Crown side piece a. Twisted, distorted or excessive fullness X X X X X X b. Top edge poorly shaped or puckered 19 Provided by IHSNot for ResaleNo reproduct

49、ion or networking permitted without license from IHS-,-,-Defect - I MIL-C-7014B 4 7777906 0433742 O W MIL-C-87014B(CG) Table IV - Classification of Defects (contd) Classification Major Minor AB X Crown side piece (contd) c. Side-crown joining seam raised toward crown d. Crease line at center of crown not aligned with center e. Crown exposed more than 1/8 inch above side front and c