NAVISTAR TMS MASTER INDEX-2017 TMS Master Index.pdf

《NAVISTAR TMS MASTER INDEX-2017 TMS Master Index.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR TMS MASTER INDEX-2017 TMS Master Index.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. JANUARY 2017 Page 1 of 4 NAVISTAR, INC. TMS (Truck Material Specifications) Number

2、: TMS Master Index Title: TMS Master Index Index Revision: 1704- January 2017 Author/s: Materials Engineering Approver/s: Materials Engineering Supersedes Issue of: 1650 December 2016 PRINTED COPIES OF THESE DOCUMENTS MUST BE VERIFIED FOR CURRENT REVISION Document No. Title Revision Issue Date TMS-1

3、xxx Ferrous Metals, Wrought TMS-1001 Mirror Assembly, Exterior 1308 August 2013 TMS-1013 Frame Steel, Ultra High-Strength, Heat-Treated E October 2007 TMS-1026 Ball Stud, High Strength, Wear Resistant 1108 August 2011 TMS-1031 Steel Tubing, Power Transmission F-1 August 2000 TMS-1033 Shafts, Steel I

4、nduction Hardened H-1 August 2000 TMS-1051 Shaft Components 1402 February 2014 TMS-1055 Spring Pins 1004 April 2010 TMS-1056 Rear Axle Housing (International Design) B-1 August 2000 TMS-1057 Striker Pin Assembly, Door Lock D-1 August 2000 TMS-1062 Clamps, Spring Tension, Type CTB 1210 October 2012 T

5、MS-1064 Suspension Stabilizer Bars B August 2007 TMS-1066 Driveline Components NEW August 2007 TMS-1068 Bellows Flexible Pipe 1308 August 2013 TMS-2xxx Ferrous Metals, Cast TMS-2014 Gray Cast Iron, Brake Drum E-1 August 2000 TMS-3xxx Non-Ferrous, Aluminum TMS-3102 Cast Aluminum Wheels A April 2006 T

6、MS-4xxx Surface Coatings, Chemical Conversion TMS-4002 Pre-Paint Treatment of Aluminum 1410 October 2014 TMS-41xx Coatings, Metallic TMS-4115 Weldable Primer on Steel A August 2004 TMS-4502 Painting, Metal or Plated Plastics D December 2003 TMS-4505 Enamel, Air Dry, Texture Finish C-1 September 2000

7、 TMS-4508 Metric Blue Identification B-1 September 2000 TMS-4510 Coating, Weld Through, Corrosion-Resistant, Hot Melt 0912 December 2009 TMS-4514 Ink-Striping Cross-Linked Polyethylene Wire Insulation 0912 December 2009 TMS-4523 Corrosion-Resistant Zinc-Aluminum Integrally Lubricated Inorganic Coati

8、ng NEW February 2006 TMS-4525 Corrosion Protective Coating for Use with Treated Wood 0908 August 2009 TMS-5xxx Powdered Metal TMS-5003 Powdered Metal Crankshaft Adapters B-1 September 2000 TMS-5004 Powdered Metal Bushings, Weldable F-1 September 2000 TMS-5012 Powdered Metal Spacers C-1 September 200

9、0 TMS-5015 Powdered Metal Spacer B-1 September 2000 TMS-6xxx Rubber, Dense TMS-6003 Wire Reinforced Air Duct 0904 April 2009 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications Master Index Jan. 2017 This document is restricted and may not be sent outside Navi

10、star, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. JANUARY 2017 Page 2 of 4 Document No. Title Revision Issue Date TMS-6004 Pads, Rubber Plied 1310 October 2013 TMS-6028 Hose, Fuel and Oil Resi

11、stant, Filler Neck 0904 April 2009 TMS-6033 Air Duct, Engine, Clean Air G October 2007 TMS-6039-R-BC Rubber (TSR) Molding Compounds (Restricted) - Barry Controls 1012 December 2010 TMS-6039-R-Tenneco Rubber (TSR) Molding Compounds (Restricted) - Tenneco 0810 October 2008 TMS-6039-R-Trelleborg Rubber

12、 (TSR) Molding Compounds (Restricted) - Trelleborg 0806 June 2008 TMS-6039-R-Semyung Rubber (TSR) Molding Compounds (Restricted) Semyung 1012 December 2010 TMS-6044 Rear Hood Mounting A June 2007 TMS-6050 CNG Vent Lines and Fuel Hoses with End Fittings & Tube Assemblies 1312 December 2013 TMS-65xx R

13、ubber, Foam TMS-6500 Cellular Polyurethane, Integral Skin 0810 October 2008 TMS-6501 Molded Seats, Urethane Foam H-1 August 2001 TMS-6502 Urethane, Cellular, Molded C-1 August 2001 TMS-6506 Urethane Foam, Slush Material C-1 August 2001 TMS-6509 Treated Urethane Foam, Acoustical B-1 August 2001 TMS-6

14、511 Foam Recirculation Seals A-1 August 2001 TMS-6513 Impact Energy Absorbing Foam 1012 December 2010 TMS-66xx Insulators (Sound, Thermal) TMS-6601 Sound Deadener, Polymeric Molded & Sheet 1306 June 2013 TMS-6611 Insulation, Heat Shrinkable Tubing A February 2006 TMS-68xx Fuels and Lubricants TMS-68

15、01 Grease, High Temperature Resistant 0908 August 2009 TMS-6803 Transmission Gear Lubricant 1210 October 2012 TMS-6814 Lubricant, Corrosion Control (Disk Brakes) 0908 August 2009 TMS-6815 Sheet Metal Processing Lubricants D April 2006 TMS-6817 Wax Lubricants for Threaded Nuts and Fasteners 0908 Augu

16、st 2009 TMS-6819 Grease, Dielectric 0806 June 2008 TMS-6820 Brake Fluid DOT 3 0906 June 2009 TMS-69xx Adhesives, Sealers, and Tapes TMS-6904 Tape, Plastic Electrical, Adhesive Tape 0904 April 2009 TMS-6907 Sealer, Butyl Rubber, Gun Grade 1106 June 2011 TMS-6913 Electrical Sealant 1008 August 2010 TM

17、S-6918 Sealer, Assembled Parts 0912 December 2009 TMS-6931 Bus Floor Mat and Step Tread Adhesives 1208 August 2012 TMS-6933 Wood Joining Adhesives 1010 October 2010 TMS-7xxx Plastics, Fabrics TMS-7000 ABS, Unfilled, Molded 1110 October 2011 TMS-7039 Polyethylene, Unfilled Molded F August 2005 TMS-70

18、40 Polypropylene, Unfilled Molded F August 2005 TMS-7055 Acetals, Molded F August 2005 TMS-7057 Anaerobic Compounds 0904 April 2009 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications Master Index Jan. 2017 This document is restricted and may not be sent outsi

19、de Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. JANUARY 2017 Page 3 of 4 Document No. Title Revision Issue Date TMS-7067 Non-Woven Padding, Fiberbond D-1 August 2001 TMS-7072 Foundati

20、on Board, Door Trim F-1 August 2001 TMS-7078 Polypropylene, Talc-Filled, Molded F August 2005 TMS-7079 Bright Decorative Metallizing Plastics D August 2005 TMS-7086 Decorative Hot Stamp Roll Leaf Coating - Plastics E August 2005 TMS-7088 Ticking, Mattress Cover G October 2007 TMS-7100 PVC Injection

21、Molding Compound 0904 April 2009 TMS-7101 Thermoplastic Engine Air Intake System Components 1010 October 2010 TMS-7102 Mineral/Glass-Filled Nylon J-1 August 2001 TMS-7107 Interior Wood Grain Decorative Films G October 2005 TMS-7111 Grille, Exterior, Thermoplastic, Prime Painted B-1 August 2001 TMS-7

22、119 Plastic Aerodynamic Components F June 2005 TMS-7120 Sunvisors 1008 August 2010 TMS-7121 Vinyl Coated Interior Trim and Seating Materials 1110 October2011 TMS-7127 Mattresses C-1 October 2007 TMS-7129 Coolant Deaeration Reservoir- Polypropylene Copolymer B August 2000 TMS-7131 Driver Air Bag (DAB

23、) C August 2005 TMS-9xxx Painting TMS-9000 Texture Paint Processing Procedure 0908 August 2009 TMS-9001 Pre-paint Processing Materials 0908 August 2009 TMS-9010 Paint Mask, Plastic Film Type 0908 August 2009 TMS-9015 Painted Metal Parts for High-Heat Resistance 1010 October 2010 TMS-9017 Gel Coat Pr

24、operties for Exterior Panels 1102 February 2011 TMS-9018 CARC Painting NEW 1212 December 2012 TMS-95xx Procedures TMS-9502 Cleanliness Of Radiator Assemblies 1012 December 2010 TMS-9503 Exterior Plastic Film, Application Procedure 0912 December 2009 TMS-9505 Axle Housing Welds Specifications B-1 Aug

25、ust 2001 TMS-9512 Automotive Frame Quality Weld Specifications 1210 October 2012 TMS-9525 Vent Window Leakage Test 0912 December 2009 TMS-9526 Axle Housing Weld Specifications D June 2007 TMS-9527 Pinstriping 0912 December 2009 TMS-9529 Thermal Cycle Test, Charge Air Cooler B-1 August 2001 TMS-9530

26、Brake Proportioning System, Test Method 1312 December 2013 TMS-9531 Air Cleaner Performance Requirements A-1 August 2001 TMS-9532 Quality Requirements for Engine Assemblies 1008 August 2010 TMS-9535 Quality Requirements for Clutch Assemblies B-1 August 2001 TMS-9536 Quality Requirements for Transfer

27、 Cases B-1 August 2001 TMS-9537 Quality Requirements for Punched and Drilled Holes A-1 August 2001 TMS-9541 Quality Requirements for Driveline Components C-1 August 2001 TMS-9545 Cab Leakage-Test Requirements 1304 April 2013 TMS-9547 Quality Requirements for Mufflers and Exhaust Aftertreatment Modul

28、es 1312 December 2013 TMS-9549 Assembly and Testing Procedures for Pierce Studs and Nuts NEW September 2000 TMS-9550 Quality Requirements for Cab Suspension Modules NEW September 2000 TMS-9551 A/C Evacuation and Charging Procedures NEW April 2001 TMS-9552 Quality Requirements for Lift Axle Assemblie

29、s NEW June 2001 TMS-9559 Adhesive Tear Down and Separation Testing Methods 1012 December 2010 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications Master Index Jan. 2017 This document is restricted and may not be sent outside Navistar, Inc. or reproduced withou

30、t permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. JANUARY 2017 Page 4 of 4 Document No. Title Revision Issue Date TMS-9562 Quality Requirements for Laser Welded Parts NEW 1212 December 2012 REVISION HISTORY Revision Level C

31、hange Approved by Date Approved 1637 Removed TMS 1045 R. Goluch 9/16/2016 1640 Removed TMS 6606, 6608,6609, 6910, 7066, 7067, 7113, 7117, 7124, 7126, 9602 R. Goluch 10/7/2016 1642 Removed TMS 6008, 6510, 9015 and 9523 R. Goluch 10/20/2016 1645 Removed TMS 6612 R. Goluch 11/8/2016 1650 Removed TMS 7099 R. Goluch 12/6/2016 1704 Remove TMS 4106, 9522 R. Goluch 1/13/2017