NAVISTAR TMS MASTER INDEX-2016 TMS Master Index.pdf

《NAVISTAR TMS MASTER INDEX-2016 TMS Master Index.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR TMS MASTER INDEX-2016 TMS Master Index.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 1 of 5 NAVISTAR, INC. TMS (Truck Material Specifications) Number:

2、TMS Master Index Title: TMS Master Index Index Revision: June 2016 Author/s: Materials Engineering Approver/s: Materials Engineering Supersedes Issue of: December 2015 PRINTED COPIES OF THESE DOCUMENTS MUST BE VERIFIED FOR CURRENT REVISION Document No. Title Revision Issue Date TMS-1xxx Ferrous Meta

3、ls, Wrought TMS-1001 Mirror Assembly, Exterior 1308 Aug. 2013 TMS-1013 Frame Steel, Ultra High-Strength, Heat-Treated E Oct 2007 TMS-1026 Ball Stud, High Strength, Wear Resistant 1108 August 2011 TMS-1031 Steel Tubing, Power Transmission F-1 August 2000 TMS-1033 Shafts, Steel Induction Hardened H-1

4、August 2000 TMS-1045 Corrosion Resistant Steel Tubing J April 2008 TMS-1051 Shaft Components 1402 Feb. 2014 TMS-1055 Spring Pins 1004 April 2010 TMS-1056 Rear Axle Housing (International Design) B-1 August 2000 TMS-1057 Striker Pin Assembly, Door Lock D-1 August 2000 TMS-1062 Clamps, Spring Tension,

5、 Type CTB 1210 Oct. 2012 TMS-1064 Suspension Stabilizer Bars B Aug 2007 TMS-1065 Tapered Roller Bearings for Wheel End Applications 1204 April 2012 TMS-1066 Driveline Components NEW Aug 2007 TMS-1068 Bellows Flexible Pipe 1308 Aug 2013 TMS-2xxx Ferrous Metals, Cast TMS-2014 Gray Cast Iron, Brake Dru

6、m E-1 August 2000 TMS-3xxx Non-Ferrous, Aluminum TMS-3100 Tubing, Copper, Air Brake E June 2007 TMS-3102 Cast Aluminum Wheels A April 2006 TMS-4xxx Surface Coatings, Chemical Conversion TMS-4002 Pre-Paint Treatment of Aluminum 1410 Oct. 2014 TMS-41xx Coatings, Metallic TMS-4106 Seat Belt Hardware Co

7、rrosion Resistance D-1 Sept. 2000 TMS-4113 Black Electrodeposited Organic Coating for Decorative Interior Applications 1002 Feb. 2010 TMS-4115 Weldable Primer on Steel A August 2004 Coatings, Non-Metallic TMS-4502 Painting, Metal or Plated Plastics D Dec. 2003 TMS-4505 Enamel, Air Dry, Texture Finis

8、h C-1 Sept. 2000 TMS-4508 Metric Blue Identification B-1 Sept. 2000 TMS-4510 Coating, Weld Through, Corrosion-Resistant, Hot Melt 0912 Dec 2009 TMS-4514 Ink-Striping Cross-Linked Polyethylene Wire Insulation 0912 Dec 2009 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material S

9、pecifications Master Index JUNE 2016 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 2 of 5 Document No. Title Revi

10、sion Issue Date TMS-4517 Interior Trim Panels-Wood Grain B Aug. 2003 TMS-4523 Corrosion-Resistant Zinc-Aluminum Integrally Lubricated Inorganic Coating NEW Feb. 2006 TMS-4524 Fluorocarbon Coating for Fasteners NEW Dec. 2007 TMS-4525 Corrosion Protective Coating for Use with Treated Wood 0908 August

11、2009 TMS-5xxx Powdered Metal TMS-5003 Powdered Metal Crankshaft Adapters B-1 Sept. 2000 TMS-5004 Powdered Metal Bushings, Weldable F-1 Sept. 2000 TMS-5012 Powdered Metal Spacers C-1 Sept. 2000 TMS-5015 Powdered Metal Spacer B-1 Sept. 2000 TMS-6xxx Rubber, Dense TMS-6003 Wire Reinforced Air Duct 0904

12、 April 2009 TMS-6004 Pads, Rubber Plied 1310 Oct. 2013 TMS-6008 Masticated Rubber Sheet 1206 June 2012 TMS-6028 Hose, Fuel and Oil Resistant, Filler Neck 0904 April 2009 TMS-6033 Air Duct, Engine, Clean Air G October 2007 TMS-6039 Rubber (TSR) Molding Compounds 1302 Feb. 2013 TMS-6039-R-BC Rubber (T

13、SR) Molding Compounds (Restricted) - Barry Controls 1012 Dec 2010 TMS-6039-R-Tenneco Rubber (TSR) Molding Compounds (Restricted) - Tenneco 0810 Oct 2008 TMS-6039-R-Trelleborg Rubber (TSR) Molding Compounds (Restricted) - Trelleborg 0806 June 2008 TMS-6039-R-Semyung Rubber (TSR) Molding Compounds (Re

14、stricted) Semyung 1012 Dec 2010 TMS-6041 Flooring Components, Bus 0810 Oct. 2008 TMS-6044 Rear Hood Mounting A June 2007 TMS-6050 CNG Vent Lines and Fuel Hoses with End Fittings & Tube Assemblies 1312 Dec. 2013 TMS-65xx Rubber, Foam TMS-6500 Cellular Polyurethane, Integral Skin 0810 Oct 2008 TMS-650

15、1 Molded Seats, Urethane Foam H-1 August 2001 TMS-65xx Rubber, Foam (contd) TMS-6502 Urethane, Cellular, Molded C-1 August 2001 TMS-6506 Urethane Foam, Slush Material C-1 August 2001 TMS-6509 Treated Urethane Foam, Acoustical B-1 August 2001 TMS-6510 Urethane Foam, Low Permeability B-1 August 2001 T

16、MS-6511 Foam Recirculation Seals A-1 August 2001 TMS-6513 Impact Energy Absorbing Foam 1012 Dec 2010 TMS-66xx Insulators (Sound, Thermal) TMS-6601 Sound Deadener, Polymeric Molded & Sheet 1306 June 2013 TMS-6606 Insulation, Floor Mat, Dash and Carpet (E-5 Type) 1002 Feb 2010 Written and Approved by:

17、 Materials Engineering NAVISTAR, INC. Truck Material Specifications Master Index JUNE 2016 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navist

18、ar, Inc. JUNE 2016 Page 3 of 5 Document No. Title Revision Issue Date TMS-6608 Floor Mat, High Density Rubber, Sound Barrier 0908 Aug 2009 TMS-6609 Molded Fiberglass, Cab Insulator 1206 June 2012 TMS-6611 Insulation, Heat Shrinkable Tubing A Feb. 2006 TMS-6612 Insulation, Acoustic 1104 Apr 2011 TMS-

19、68xx Fuels and Lubricants TMS-6801 Grease, High Temperature Resistant 0908 August 2009 TMS-6803 Transmission Gear Lubricant 1210 Oct. 2012 TMS-6811 Lubricant, Power Steering 0908 August 2009 TMS-6812 Lubricant, Transmission (Automatic) 0806 June 2008 TMS-6814 Lubricant, Corrosion Control (Disk Brake

20、s) 0908 August 2009 TMS-6815 Sheet Metal Processing Lubricants D April 2006 TMS-6817 Wax Lubricants for Threaded Nuts and Fasteners 0908 August 2009 TMS-6818 Refrigeration Lubricants 0908 August 2009 TMS-6819 Grease, Dielectric 0806 June 2008 TMS-6820 Brake Fluid DOT 3 0906 June 2009 TMS-69xx Adhesi

21、ves, Sealers, and Tapes TMS-6904 Tape, Plastic Electrical, Adhesive Tape 0904 April 2009 TMS-6907 Sealer, Butyl Rubber, Gun Grade 1106 June 2011 TMS-6910 Cellular Vinyl Tape (Sealing) 1004 April 2010 TMS-6913 Electrical Sealant 1008 Aug 2010 TMS-6918 Sealer, Assembled Parts 0912 Dec 2009 TMS-6928 Se

22、alant, Preformed Patches 0904 April 2009 TMS-6930 Glass Assembly Adhesive 0912 Dec 2009 TMS-6931 Bus Floor Mat and Step Tread Adhesives 1208 Aug 2012 TMS-6933 Wood Joining Adhesives 1010 Oct 2010 TMS-7xxx Plastics, Fabrics TMS-7000 ABS, Unfilled, Molded 1110 Oct 2011 TMS-7005 Thread, Nylon or Dacron

23、 H Aug. 2005 TMS-7028 Bonded Trim Composites, Interior K Aug 2007 TMS-7039 Polyethylene, Unfilled Molded F Aug. 2005 TMS-7040 Polypropylene, Unfilled Molded F Aug. 2005 TMS-7051 Decorative Electroplated Chromium - Plastics H Oct 2007 TMS-7055 Acetals, Molded F Aug. 2005 TMS-7057 Anaerobic Compounds

24、0904 April 2009 TMS-7066 Laminated Fiberboard, Head Board F Aug. 2005 TMS-7067 Non-Woven Padding, Fiberbond D-1 August 2001 TMS-7072 Foundation Board, Door Trim F-1 August 2001 TMS-7078 Polypropylene, Talc-Filled, Molded F Aug. 2005 TMS-7079 Bright Decorative Metallizing Plastics D Aug. 2005 TMS-708

25、6 Decorative Hot Stamp Roll Leaf Coating - Plastics E Aug. 2005 TMS-7088 Ticking, Mattress Cover G Oct 2007 TMS-7099 Fastener Tape Systems 0912 Dec 2009 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications Master Index JUNE 2016 This document is restricted and

26、may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 4 of 5 Document No. Title Revision Issue Date TMS-7100 PVC Injection Molding Compound 0904 April 20

27、09 TMS-7101 Thermoplastic Engine Air Intake System Components 1010 Oct 2010 TMS-7102 Mineral/Glass-Filled Nylon J-1 August 2001 TMS-7107 Interior Wood Grain Decorative Films G Oct. 2005 TMS-7xxx Plastics, Fabrics (contd) TMS-7111 Grille, Exterior, Thermoplastic, Prime Painted B-1 August 2001 TMS-711

28、3 Woven or Knit Fabric, Interior Trim - Parts 1 and 2 1310 Oct. 2013 TMS-7117 Foam Composite Trim Panel A-1 August 2001 TMS-7119 Plastic Aerodynamic Components F June 2005 TMS-7120 Sunvisors 1008 Aug 2010 TMS-7121 Vinyl Coated Interior Trim and Seating Materials 1110 Oct.2011 TMS-7124 Interior Struc

29、tural Foam RIM 0908 August 2009 TMS-7125 Composite Trim Panels 1106 June 2011 TMS-7126 Carpet Trim Materials 1006 June 2010 TMS-7127 Mattresses C-1 Oct 2007 TMS-7129 Coolant Deaeration Reservoir- Polypropylene Copolymer B August 2000 TMS-7131 Driver Air Bag (DAB) C Aug. 2005 TMS-9xxx Painting TMS-90

30、00 Texture Paint Processing Procedure 0908 August 2009 TMS-9001 Pre-paint Processing Materials 0908 August 2009 TMS-9010 Paint Mask, Plastic Film Type 0908 August 2009 TMS-9013 Phosphate and E-Coat Systems Compatibility 0902 Feb. 2009 TMS-9015 Painted Metal Parts for High-Heat Resistance 1010 Oct 20

31、10 TMS-9017 Gel Coat Properties for Exterior Panels 1102 Feb 2011 TMS-9018 CARC Painting NEW 1212 Dec 2012 TMS-95xx Procedures TMS-9502 Cleanliness Of Radiator Assemblies 1012 Dec 2010 TMS-9503 Exterior Plastic Film, Application Procedure 0912 Dec 2009 TMS-9505 Axle Housing Welds Specifications B-1

32、August 2001 TMS-9512 Automotive Frame Quality Weld Specifications 1210 Oct. 2012 TMS-9522 Glazing J Feb 2008 TMS-9523 Development, Quality Control Procedures for SMC-FRP Parts D August 2006 TMS-9525 Vent Window Leakage Test 0912 Dec 2009 TMS-9526 Axle Housing Weld Specifications D June 2007 TMS-9527

33、 Pinstriping 0912 Dec 2009 TMS-9529 Thermal Cycle Test, Charge Air Cooler B-1 August 2001 TMS-9530 Brake Proportioning System, Test Method 1312 Dec. 2013 TMS-9531 Air Cleaner Performance Requirements A-1 August 2001 TMS-9532 Quality Requirements for Engine Assemblies 1008 August 2010 TMS-9535 Qualit

34、y Requirements for Clutch Assemblies B-1 August 2001 TMS-9536 Quality Requirements for Transfer Cases B-1 August 2001 TMS-9537 Quality Requirements for Punched and Drilled Holes A-1 August 2001 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications Master Index J

35、UNE 2016 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 5 of 5 Document No. Title Revision Issue Date TMS-9541 Qua

36、lity Requirements for Driveline Components C-1 August 2001 TMS-9544 Flammability Certification of Interior Trim Materials and Components 1310 Oct. 2013 TMS-9545 Cab Leakage-Test Requirements 1304 April 2013 TMS-9547 Quality Requirements for Mufflers and Exhaust Aftertreatment Modules 1312 Dec. 2013

37、TMS-9549 Assembly and Testing Procedures for Pierce Studs and Nuts NEW Sept. 2000 TMS-9550 Quality Requirements for Cab Suspension Modules NEW Sept. 2000 TMS-9551 A/C Evacuation and Charging Procedures NEW April 2001 TMS-9552 Quality Requirements for Lift Axle Assemblies NEW June 2001 TMS-9559 Adhes

38、ive Tear Down and Separation Testing Methods 1012 Dec 2010 TMS-9562 Quality Requirements for Laser Welded Parts NEW 1212 Dec. 2012 TMS-96xx Product Lifecycle Design Procedures TMS-9602 Reporting Recycled Content of International Products A-1 August 2001 TMS-9605 Engineering Weight Calculations B August 2007