NAVISTAR MPAPS G-6046-2017 Elastomeric Coatings.pdf

《NAVISTAR MPAPS G-6046-2017 Elastomeric Coatings.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS G-6046-2017 Elastomeric Coatings.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. MARCH 2017 Page 1 of 8 NAVISTAR, INC. Material, Parts, and Process Specifications

2、 (MPAPS) NUMBER: MPAPS G-6046 Former Designation: TMS-6046 TITLE: Elastomeric Coatings CURRENT REV No.: 1703 DATE: March 2017 WRITTEN/EDITED BY: S. Brailey APPROVED BY: R. Goluch SUPERSEDES: Rev. 1610 October 2016 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specificati

3、on may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to

4、use. 1.0 APPLICATION This specification applies to elastomeric coatings, generally polyurea, urethane and hybrids of those polymers. This specification may be applied to chemicals purchased to coat parts or parts coated by a supplier. 2.0 SCOPE This specification covers the qualification and process

5、ing, quality, quality control and source approval, and packaging requirements of chemicals and finished parts. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specificatio

6、n. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 MPAPS P-9543 SAE J243 CFR Title 29, Part 1910 A

7、STM D395 SAE J400 NAVISTAR Supplier Packing & Shipping Std D-13 ASTM D412 NAVISTAR Engineering Design Std A-16 ASTM D573 NAVISTAR MPAPS B-50 ASTM D624 MPAPS DT-12 ASTM D2137 MPAPS GT-31 ASTM D2240 MPAPS GT-Paint ASTM D4878 4.0 REQUIREMENTS This specification is not intended to limit or to specify th

8、e exact processes and/or materials to be used in providing finished parts. The control of the primer quality and its application are the responsibility of the supplier. All finished coated parts shall be compatible with all subsequent NAVISTAR operations. 4.1 Qualification of Coatings 4.1.1 Material

9、/Process Approvals The coatings and pre-treatments used by the supplier must be approved by Materials Engineering prior to their first use in production. In addition, parts coated with the materials and applications processes/methods to be used by the supplier shall be approved by Materials Engineer

10、ing and, after NUMBER: MPAPS G-6046 TITLE: Elastomeric Coatings REVISION: 1703 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. MAR

11、CH 2017 Page 2 of 8 approval, no deviation in materials and/or manufacturing processes are permitted without approval by Materials Engineering. 4.1.2 Material The initial qualification tests of paint shall be performed on parts formed from the same material and by the same process in which the finis

12、hed parts are specified. These panels shall be coated with the materials to be tested using the procedure listed below. In cases where a primer is specified in addition to the topcoat, the panels shall contain both coatings applied by the intended production process. These panels shall be submitted

13、to Materials Engineering for approval with the vendors test results. Final qualification shall be performed on the finished part prior to production release. 4.1.3 Sample Preparation 4.1.3.1 A minimum of three (3) parts shall be submitted for qualification for each test. 4.1.3.2 Prior to coating, th

14、e samples shall be cleaned with solvents or cleaners as necessary. This operation shall simulate production procedure. 4.1.3.3 The primer, if applicable, shall be applied to a minimum dry film thickness per the manufacturers recommended process. 4.1.3.4 The coated samples shall be cured by means whi

15、ch simulate production procedures. 4.2 Testing Finish painted parts, primed or unprimed, when coated with approved materials will meet the applicable requirements listed in Table 1. 4.2.1 Coatings used in flooring applications will meet the requirements listed in the table below in addition to Table

16、 1. Test Test Method Requirements Accelerated Weathering MPAPS GT-31 Method E Expose separate sets of samples for 100 and 500 hours per method. No color change greater than E of 3, degradation, cracking, wrinkling, or loss of adhesion after 100 hours exposure. Report 500 hour results. Flammability F

17、MVSS 302 Meet the requirements of the latest issue Coefficient of Friction ASTM D2047 0.8 minimum Hardness (5 points) ASTM D2240 Type A 90 Tensile Strength (psi) ASTM D412 3000 minimum Low Temperature Resistance ASTM D2137, Method A Non-brittle at -40C (-40F) Pass Tear Resistance (pli) ASTM D624, Di

18、e C 500 minimum Heat Resistance ASTM D573, 70 hrs at 70C Hardness ASTM D2240 Type A 10 (max. % change) Tensile Strength ASTM D412, Die C 30 (max. % change) Tear Resistance ASTM D412, Die C -50 (max. % change) Mandrel Flexibility Test ” mandrel Pass 4.3 Material Properties Table 2 lists the required

19、cured material properties. 4.4 Processing Finished painted production parts shall be produced by the same methods used on the qualification samples. Changes in processing must be approved by Materials Engineering. NUMBER: MPAPS G-6046 TITLE: Elastomeric Coatings REVISION: 1703 This document is restr

20、icted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. MARCH 2017 Page 3 of 8 5.0 QUALITY Painted parts shall be adherent and uniform in color and texture, wit

21、h no thin spots, runs, wrinkles, porosity, pits, blisters or nodules. Material supplied shall be free from objectionable odor, be of uniform quality, and shall match performance properties of pre-production approved material. Pre-production samples of material sufficient for complete test and evalua

22、tion should be submitted to Materials Engineering for approval 5.1 Porosity In instances where porosity is not detectable until after the primed substrate has been painted, isolated cases of porosity as defined in Table 4 shall not be cause for rejection. Porosity that is chronic and requires signif

23、icant amounts of rework shall be cause for rejection and it is the responsibility of the supplier to correct this condition. The supplier has the responsibility to provide quality primed parts which will not cause delayed defects after finishing in the using plant. This condition will require close

24、cooperation with the paint facility and with Materials Engineering. 5.2 Appearance Requirements Specific appearance requirements are given in Table 3. Appearance requirements are specified for the following zones or locations on the vehicle: 5.2.1 Zone I Primary: exterior, glamour surfaces such as h

25、oods and fender exteriors, including visible edges, bumpers, grilles, cab fronts, sides, doors, corners, and lower aerodynamic fairings. 5.2.2 Zone II Secondary: exterior, glamour surfaces such as cab tops, cab backs (between corner radii), and upper aerodynamic fairings. Also, primary interior, sur

26、faces, such as engine covers. 5.2.3 Zone III Recessed exterior or interior surfaces, such as door openings, door ends, painted grab handles, and floors or beds. 5.2.4 Zone IV Hidden areas, such as those covered in assembly and under hood or body. 5.2.5 Inspection Conditions Parts shall be inspected

27、for appearance requirements at a distance of two feet under a light intensity of 100 foot-candles minimum at the part surface. 5.3 Qualification Samples shall be accompanied by test data certifying that all requirements of the specification have been met. Data submitted shall include the following:

28、5.3.1 Report: A detailed and signed report documenting testing to this specification prepared in accordance with MPAPS P-9543. The report will include actual test data and not merely test summaries. 5.3.2 Failure Modes: Test samples or photographs showing failure modes for each destructive test 5.3.

29、3 Test Procedure: The procedures used for preparing and testing material. 5.3.4 Analysis: A detailed analysis of the test results including assumptions made, unexpected results and an explanation of any non-compliant results. 5.3.5 Material: Pre-production material sufficient for complete test and e

30、valuation by Navistar 5.4 Submission The material and test report shall be submitted to: Materials Engineering, Navistar Inc., 10400 W. North Ave, Melrose Park, IL 60160. NUMBER: MPAPS G-6046 TITLE: Elastomeric Coatings REVISION: 1703 This document is restricted and may not be sent outside Navistar,

31、 Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. MARCH 2017 Page 4 of 8 5.5 Approval A report from Navistar will be issued, approving material to this specification. Approval is not formally grant

32、ed until this report has been published. A change to this specification listing the new approval may be delayed. The approval report serves as authorization for the use of that system prior to the changes to this specification. 6.0 QUALIFICATION Engineering qualification of sources is required in ad

33、vance of production shipments. Samples shall be accompanied by test data certifying that all requirements of the specification have been met. Suppliers shall submit samples for approval of finish, luster, color and appearance to the Navistar Industrial Design Group. Upon approval, styling master sam

34、ples denoting the minimum level of acceptable appearance quality shall be developed and retained by the supplier and the quality department of each using NAVISTAR facility. 6.1 Quality Control Plan A Quality Control Plan for products supplied to the requirements of this specification will be establi

35、shed by mutual agreement between NAVISTAR and the supplier. Unless specific exception is noted, the following characteristics, where applicable*, shall be included in the plan as features for management by statistical process control.* * Other characteristics for inclusion in the control plan may be

36、 specified on the engineering drawing and/or purchase order. * See NAVISTAR Engineering Design Standard A-16 7.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS

37、-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Corporate Buye

38、r upon request. 7.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that ch

39、anges in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify NAVISTAR Materials Engineering and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this

40、specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 7.3 Process Control The supplier shall either, perform and report results of tests on specific lots of parts pro

41、duced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier Paint film thickness as per ASTM D1186 Adhesion of paint as per ASTM D3359

42、 NUMBER: MPAPS G-6046 TITLE: Elastomeric Coatings REVISION: 1703 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. MARCH 2017 Page 5

43、 of 8 and the quality control manager of the using NAVISTAR plant may determine testing and reporting requirements on specific products. 8.0 SHIPPING AND HANDLING Shipping and identification shall be in accordance with NAVISTAR Manufacturing Standard MS-D-13. Parts shall be packaged so as to avoid a

44、ny damage in shipment detrimental to the appearance of the part. 9.0 DESIGNATION ON DRAWINGS Example of note to use on drawings: Coat per MPAPS G-6046 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled

45、 copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Markit Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ NUMBER: MPA

46、PS G-6046 TITLE: Elastomeric Coatings REVISION: 1703 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. MARCH 2017 Page 6 of 8 TABLE

47、1 FILM PERFORMANCE REQUIREMENTS Test* Test Method Requirements Adhesion(1) ASTM D3359 Method B 95% Min. Peel per ASTM D903, kN/m 5 Min. Accelerated Adhesion (Water immersion, 49C) GT-Paint, method 5C Steps 2,3,4,5,6 & 7 Under Procedure 95% Min. Same as above except Peel per ASTM D903, kN/m and 168 h

48、r immersion 4.5 Min. Initial Gloss GT-Paint, method 6B Step 3 Under Procedure Shall Match Color Standard in the Navistar Styling Department Intercoat Adhesion GT-Paint, method 5B 95% Min. Color(1) Visual comparison Shall Match Color Standard in the Navistar Styling Department Mar Resistance(1) GT-Pa

49、int, method 12 Steps 4.1 to 4.4 Under Procedure No Nail Marks Visible To The Unaided Eye Gravelometer SAE J400 2A as per GT-Paint, method 28 Humidity GT-Paint, method 7E Steps 4.2 to 4.5 (Under Procedure) Interior 100 Hours Exterior 500 Hours No Blistering At Conclusion Of Specified Time Accelerated Weathering GT-31