NAVISTAR MPAPS B-6822-2016 Lubricant Automatic Transmission Fluid (ATF) For Power Steering Systems.pdf

《NAVISTAR MPAPS B-6822-2016 Lubricant Automatic Transmission Fluid (ATF) For Power Steering Systems.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS B-6822-2016 Lubricant Automatic Transmission Fluid (ATF) For Power Steering Systems.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. SEPTEMBER 2016 Page 1 of 4 NAVISTAR, INC. Material, Parts, and Process Specificat

2、ions (MPAPS) NUMBER: MPAPS B-6822 Former Designation: NEW TITLE: Lubricant, Automatic Transmission Fluid (ATF) For Power Steering Systems CURRENT REV No.: 1609 DATE: Sept. 2016 WRITTEN/EDITED BY: J. Morris APPROVED BY: R. Goluch SUPERSEDES: NEW PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CU

3、RRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability

4、 of regulatory limits prior to use. 1.0 APPLICATION 1.1 Production Use This specification covers production automatic transmission fluid intended for use in Navistars Power Steering System requiring mineral oil based on TES 389TM fluid (DEXTRON III type) NAVISTAR Bulk P/N 6133055R1. 1.2 Service Use

5、In addition, this specification covers automatic transmission fluid intended for service use in power steering systems (Fleetrite P/N FLTPSDX3X, where the last X identifies the amount of fluid needed. For instance; P/N FLTPSDX3Q or P/N FLTPSDX3G (Q for Quart and G for Gallons). 2.0 SCOPE This specif

6、ication covers the physical and chemical properties for automatic transmission fluid meeting current TES 389TM requirements, quality plan, source approval, quality control, and shipping and identification requirements. 2.1 Restricted Chemical Substance Effective January 1, 2007, all product supplied

7、 to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this

8、specification. Quality System Standard ISO 9001 or TS-16949 ASTM D92 ASTM D2983 CFR Title 29, Part 1910 ASTM D97 ASTM D4927 NAVISTAR Supplier Packing and Shipping Std. D-13 ASTM D445 ASTM D4951 NAVISTAR Engineering Design Std A-16 ASTM D892 ASTM D6304 NAVISTAR MPAPS B-50 ASTM D2270 NUMBER: MPAPS B-6

9、822 TITLE: Lubricant, ATF for Power Steering System REVISION: 1609 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. SEPTEMBER 2016

10、Page 2 of 4 4.0 REQUIREMENTS 4.1 Physical and Chemical Properties 4.1.1 Viscosity ASTM D445; At 100 C (212F) cSt (mm/s) 7.0 minimum for mineral oil based products. ASTM D2983; At -40 C (-40F) centipoise 20,000 maximum for mineral oil based products. 4.1.2 Viscosity Index (ASTM D2270) Shall be 165 mi

11、nimum for mineral oil based products. 4.1.3 Pour Point (ASTM D97) Shall be -42C (-44F) maximum. 4.1.4 Flash Point (ASTM D92) Shall be 177C (350F) minimum. 4.1.5 Foaming (ASTM D892) When tested at the following temperatures, foaming tendency and foam stability shall be as follows: Sequence Foam Tende

12、ncy, ml Foam Stability, ml I 30 maximum 0 II 100 maximum 0 III 30 maximum 0 4.1.6 Water Content (ASTM D6304) 4.1.7 Color - Shall be red. 4.1.8 Phosphorus Content (ASTM D4927 or D4951) Shall be + 10% of qualification value. 4.1.9 Conductivity Test (ASTM D2624 or D4308) Shall be 650 pS/m, minimum 5.0

13、QUALITY All product supplied shall be suitable for the intended application clean and free from foreign materials and dirt, and suitably packaged and identified. NUMBER: MPAPS B-6822 TITLE: Lubricant, ATF for Power Steering System REVISION: 1609 This document is restricted and may not be sent outsid

14、e Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. SEPTEMBER 2016 Page 3 of 4 6.0 QUALIFICATION Engineering qualification of sources is required in advance of production. Material submitt

15、ed for qualification shall be accompanied by detailed test information and certification that material meets all requirements of this specification. 6.1 Quality Control Plan A Quality Control Plan for products supplied to the requirements of this specification will be established by mutual agreement

16、 between NAVISTAR and the supplier. Unless specific exception is noted, the following characteristics, where applicable*, shall be included in the plan as features for management by statistical process control.* * Other characteristics for inclusion in the control plan may be specified on the engine

17、ering drawing and/or purchase order. * See NAVISTAR Engineering Design Standard A-16 7.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 registration as l

18、ong as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Corporate Buyer upon request. 7.2 Appr

19、oval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, prope

20、rties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify NAVISTAR Materials Engineering and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samp

21、les, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change 7.3 Process Control The supplier shall either, perform and report results of tests on specific lots of parts produced using ISO 9001 or T

22、S-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the quality control manager of the using NAVISTAR plant may determine testing and reporting req

23、uirements on specific products. NUMBER: MPAPS B-6822 TITLE: Lubricant, ATF for Power Steering System REVISION: 1609 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent

24、liability. 2016 by Navistar, Inc. SEPTEMBER 2016 Page 4 of 4 8.0 SHIPPING AND HANDLING Shipping and identification shall be in accordance with NAVISTAR Supplier Packing and Shipping Standard D-13. Parts shall be packaged so as to avoid any damage in shipment detrimental to the appearance of the part

25、. 9.0 DESIGNATION ON DRAWINGS Example of note to use on drawings: Lubricant per MPAPS B-6822 10.0 APPROVED SOURCE Gold Eagle Mineral Oil Based ATF TES 389TM Fluid (P/N 6133055R1) 10.1 Other Approved Sources Contact Navistars Materials Engineering and Technology Dept. 11.0 TECHNICAL INFORMATION For f

26、urther information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Markit. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ REVISION HISTORY Revision Level Approved by Date Approved 1609 New release R. Goluch 9/30/2016