ITU-R SM 1840-2007 Test procedure for measuring the sensitivity of radio monitoring receivers using analogue-modulated signals《测量使用模拟调制信号无线电监测接收机灵敏度的测试程序》.pdf

《ITU-R SM 1840-2007 Test procedure for measuring the sensitivity of radio monitoring receivers using analogue-modulated signals《测量使用模拟调制信号无线电监测接收机灵敏度的测试程序》.pdf》由会员分享，可在线阅读，更多相关《ITU-R SM 1840-2007 Test procedure for measuring the sensitivity of radio monitoring receivers using analogue-modulated signals《测量使用模拟调制信号无线电监测接收机灵敏度的测试程序》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 Recommendation ITU-R SM.1840(12/2007)Test procedure for measuring the sensitivity of radio monitoring receivers using analogue-modulated signalsSM SeriesSpectrum managementii Rec. ITU-R SM.1840 Foreword The role of the Radiocommunication Sector is to ensure the rational, equitable, efficient and ec

2、onomical use of the radio-frequency spectrum by all radiocommunication services, including satellite services, and carry out studies without limit of frequency range on the basis of which Recommendations are adopted. The regulatory and policy functions of the Radiocommunication Sector are performed

3、by World and Regional Radiocommunication Conferences and Radiocommunication Assemblies supported by Study Groups. Policy on Intellectual Property Right (IPR) ITU-R policy on IPR is described in the Common Patent Policy for ITU-T/ITU-R/ISO/IEC referenced in Annex 1 of Resolution ITU-R 1. Forms to be

4、used for the submission of patent statements and licensing declarations by patent holders are available from http:/www.itu.int/ITU-R/go/patents/en where the Guidelines for Implementation of the Common Patent Policy for ITU-T/ITU-R/ISO/IEC and the ITU-R patent information database can also be found.

5、Series of ITU-R Recommendations (Also available online at http:/www.itu.int/publ/R-REC/en) Series Title BO Satellite delivery BR Recording for production, archival and play-out; film for television BS Broadcasting service (sound) BT Broadcasting service (television) F Fixed service M Mobile, radiode

6、termination, amateur and related satellite services P Radiowave propagation RA Radio astronomy RS Remote sensing systems S Fixed-satellite service SA Space applications and meteorology SF Frequency sharing and coordination between fixed-satellite and fixed service systems SM Spectrum management SNG

7、Satellite news gathering TF Time signals and frequency standards emissions V Vocabulary and related subjects Note: This ITU-R Recommendation was approved in English under the procedure detailed in Resolution ITU-R 1. Electronic Publication Geneva, 2009 ITU 2009 All rights reserved. No part of this p

8、ublication may be reproduced, by any means whatsoever, without written permission of ITU. Rec. ITU-R SM.1840 1 RECOMMENDATION ITU-R SM.1840 Test procedure for measuring the sensitivity of radio monitoring receivers using analogue-modulated signals (2007) Scope This Recommendation belongs to a set of

9、 Recommendations describing the test methods to determine technical parameters of radio monitoring receivers that are important for the users of these receivers. When the described methods are followed by manufacturers, comparing different receivers is made easier. This Recommendation provides the d

10、efinition of a sensitivity test procedure for receivers. This test procedure definition is recommended to all the manufacturers, with the advantage for the users of such receivers, that an easier and more objective assessment of product quality is possible. The ITU Radiocommunication Assembly, consi

11、dering a) that ITU-R has published the Typical recommended specifications for analogue and digital monitoring receivers in the Spectrum Monitoring Handbook (2002), but that nothing is said about the test procedures behind such specifications; b) that one of the specifications that most strongly depe

12、nds on the test procedures applied is the sensitivity; c) that the sensitivity of a receiver is a measure of its ability to receive weak signals and to produce an output having a usable level and acceptable quality; d) that the sensitivity level specified in the data sheet of a receiver depends extr

13、emely on the test frequencies used, the modulation parameters, the IF filter bandwidth used, the signal-to-interference ratio including noise and distortion (SINAD) value and the ambient temperature prevailing during the tests; e) that due to the direct correlation with the noise figure the sensitiv

14、ity characteristic has a direct influence on the suitability of a receiver as a monitoring device; f) that without a defined test procedure, the sensitivity specifications published by the manufacturers have to be made comparable by some kind of conversion and that this conversion might be complex o

15、r even impossible to perform; g) that a defined test procedure for the sensitivity must be independent of receiver design; h) that a well-defined test procedure for the sensitivity, if adopted by all the manufacturers of radio monitoring receivers, will have the advantage for the users of such recei

16、vers, that an easier and more objective assessment of product quality is possible, avoiding ambiguities; j) that supplementary information about these sensitivity measurements can be found in the Report ITU-R SM.2125 Parameters of and measurement procedures on H/V/UHF monitoring receivers and statio

17、ns, 2 Rec. ITU-R SM.1840 recommends 1 that for cases in which the sensitivity of radio monitoring receivers using analogue-modulated signals is specified by administrations, the measurement method in Annex 1 should be used. Annex 1 Test procedure for measuring the sensitivity of radio monitoring rec

18、eivers using analogue-modulated signals 1 General aspects This Annex provides the definition of a test procedure to determine the sensitivity of a radio monitoring receiver. The sensitivity depends on: the noise figure; the modulation type; the frequencies used for the test; the IF bandwidth used fo

19、r the test; the SINAD value; the modulation frequency; the modulation index (for AM); the frequency deviation (for FM); the preamplifier settings; the temperature prevailing during the tests. Furthermore, to correctly assess the sensitivity: the measurements have to be done over the whole frequency

20、range of the receiver; a worst value of the sensitivity must be specified and published by the manufacturer in the data sheet over the receivers whole operating range. Since sensitivity values are frequency dependent the manufacturer can choose to additionally specify the sensitivity for selected fr

21、equency bands or ranges; a mean value (the arithmetic mean of a number of test measurements) may also be indicated; the published sensitivity values have to be valid over the entire temperature range indicated in the data sheet. Limitations, if any, have to be mentioned in the data sheet. 2 Basics o

22、f the sensitivity measurements The sensitivity of a receiver is defined as the minimum signal level (V, dBV or dBm) at the input of the receiver for demodulation and audio listening of the received signal. The minimum audible signal with acceptable quality shall be determined by a SINAD measurement.

23、 Rec. ITU-R SM.1840 3 A modulated test signal, generated by a signal generator, is inserted into the antenna input of the receiver. An audio analyser is connected to the audio output. The principle of this measurement is to reduce the signal level at the signal generator until the SINAD value is rea

24、ched. The SINAD value is measured on the audio analyser. The measurements must be done over the whole frequency range by tuning the signal generator and the receiver to the test signals with the frequencies f1, f2, . fn. AM modulation for HF and VHF/UHF band The sensitivity level is then indicated a

25、s: Sensitivity (AM) X at (preamp. “on”) 6 kHz bandwidth 12 dB SINAD fmod = 1 kHz m = 0.5 FM modulation for HF band The sensitivity level is then indicated as: Sensitivity (FM) X at (preamp. “on”) 8 kHz bandwidth 20 dB SINAD fmod = 1 kHz f = 2.4 kHz FM modulation for VHF/UHF band The sensitivity leve

26、l is then indicated as: Sensitivity (FM) X at (preamp. “on”) 15 kHz bandwidth 20 dB SINAD fmod = 1 kHz f = 5 kHz where: X is the measured sensitivity, indicated in V (or dBV or dBm) the bandwidth used is indicated the SINAD value is indicated the modulation frequency is 1 kHz the modulation index m

27、for AM the frequency deviation f for FM. The measurements must be done over the whole frequency range by tuning the receiver to the test signals with the frequencies f1, f2, . fn. Per octave at least two frequencies being evenly distributed over the full frequency range of the receiver have to be ch

28、osen. The receiver must be set up under normal operating conditions. If an input attenuator exists, it must be switched to 0 dB attenuation. The automatic gain control (AGC) must be switched on during the tests. If a switchable preamplifier exists, the measurements must be done in the condition “pre

29、amplifier on”. The condition “preamplifier on” may also be expressed as “high sensitivity mode” or “low noise mode”. 4 Rec. ITU-R SM.1840 3 Definition of a test procedure for measuring the sensitivity of radio monitoring receivers using analogue-modulated signals In addition to the general aspects a

30、nd basics stated in 1 and 2 above the following definitions for the measurements apply: The measurements have to be done for the two main modulations modes AM (A3E) and FM (F3E) at the test frequencies f1, f2, . fn. Selection of the test frequencies as stated in item No. 2. Settings of the signal ge

31、nerator for AM in the range 9 kHz-3 000 MHz: Modulation mode AM Modulation frequency 1 kHz Modulation index 0.5 for FM in the range 9 kHz-30 MHz: for FM in the range 20-3 000 MHz: Modulation mode FM Modulation mode FM Modulation frequency 1 kHz Modulation frequency 1 kHz Frequency deviation 2.4 kHz

32、Frequency deviation 5 kHz Settings of the receiver for AM: Modulation mode AM IF bandwidth 6 kHz for FM in the range 9 kHz-30 MHz: for FM in the range 20-3 000 MHz: Modulation mode FM Modulation mode FM IF bandwidth 8 kHz IF bandwidth 15 kHz If the recommended IF filter bandwidth is not available in

33、 the receiver, the next higher filter bandwidth must be chosen. The audio filter used for the measurement needs to be specified. Settings of the audio analyser: The audio analyser must be set to the measurement mode “SINAD”. The psophometric audio filter (ITU-T Recommendation P.53) in the audio anal

34、yser must be switched on. Measurement procedure Increase the signal generator level until a stable SINAD value of approx. 30 dB is displayed on the audio analyser. Rec. ITU-R SM.1840 5 Reduce the signal level until the SINAD value has reached 12 dB (for AM) or 20 dB (for FM). The corresponding level

35、 value read on the signal generator is the sensitivity of the receiver. 4 Units conversions If the sensitivity value is expressed in V it must be converted to dBm with: Value (dBV) = 20 log value (V) e.g. for 1V: 20 log 1(V) = 0 dBV Value (dBm) = Value (dBV) 107 e.g. for 0 dBV: 0 dBV 107 = 107 dBm assuming an input impedance of 50 .