INTERN ESP JM-16 101-GS-2000 Retainer Spring Pins - General Specifications - Metric Series (Noun Code - 6200)《扣具弹簧销的一般规格 公制系列(名词代码 6200)》.pdf

《INTERN ESP JM-16 101-GS-2000 Retainer Spring Pins - General Specifications - Metric Series (Noun Code - 6200)《扣具弹簧销的一般规格 公制系列(名词代码 6200)》.pdf》由会员分享，可在线阅读，更多相关《INTERN ESP JM-16 101-GS-2000 Retainer Spring Pins - General Specifications - Metric Series (Noun Code - 6200)《扣具弹簧销的一般规格 公制系列(名词代码 6200)》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL TRUCK AND ENGINE CORPORATION TITLE: Retainer Spring Pins - General Specifications - Metric Series (Noun Code - 6200) WRITTEN/REVIE WED BY: PPROVED BY: Engineering Standard Parts CURRENT ISSUE DATE: September 2000 SUPERSEDES ISSUE OF: UMBER: p ESP-JM-16.101-GS I Corporate Technical Stan

2、dards I Corporate Technical Standards I April 1989 PRl“llTD COPEKS Olt TH ES lIOCl MI?“I MUST 13K VEBREItIlTD FOR LURWlTXIT RlWISIO IChange Notice: Reformatted GENERAL SPECIFICATIONS GENERAL: Implementation of this standard must be in accordance with the policies and procedures outlined in ESP-A- 0.

3、101. There may also be supplemental group instructions in regard to use of metric standards that should be taken into account. No national or international standard exists on this product. The specifications contained herein represent a hard metric conversion of the current inch standard. Inch retai

4、ner spring pins may be found on ESP-J-16.101-GS. PREFERRED PARTS POLICY: Preferred parts are so designated to reduce variety of parts and assure maximum availability, interchangeability, and cost savings. Nominal Sizes: Finish: Plain 3,4,6, 8, 10, 12, and 16 mm MATERIAL: Spring steel wire per CEMS A

5、-9, Type 2. FINISH: Parts will be furnished plain and coated with a light oil film. PERFORMANCE REQUIREMENTS: Spring pins must be capable of withstanding repeated assembly and disassembly without breakage or appreciable loss of spring quality. COLOR CODING: Not recommended, except in cases where ade

6、quate insurance is needed to prevent mixing of “metric parts“ with look-alike “inch parts.“ The color blue is standard identifier used in some industries. This must be handled internally at individual plants where needed and is meant to be supplemental to the normal finish and easily deleted when th

7、e need for supplemental identification no longer exists. The supplemental blue color should not be used on material such as stainless steel which is specified for cosmetic purposes, or phosphate coating which may cause a loss of color identity. METHOD OF DESIGNATION: Retainer spring pins will be des

8、ignated by size, thickness, description, material, finish, and part number as shown in the following example. 6 x 1.6 mm Retainer Spring Pin, STW, PLN, Part Number WORKMANSHIP: Pins must be free from burrs. sharp edges, and all other defects that affect their serviceability. This document is restric

9、ted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 02000 International Truck and Engine Corporation. SEPTEMBER 2000 Page 1 of 2 Copyright International

10、Truck and Engine Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: ESP- JM-16.101-GS Dimensions in millimete Incrnaionall Nom TITLE: Retainer Spring Pins - Metric Series - CURRENT ISSUE DATE: General Snecif

11、ications September 2000 PartNo. I Shaft 4.2 6.2 Plain Size 3 0.9 0.9 : Unless otherwise specified, all dimensions are nominal. Thick A 0.6 0.6 0.6 1.6 1.6 1.6 2.5 2.5 2.5 FreeDia I :i I ?:11 Ring Dimensions D 1.1 1.6 2.1 2.1 3.1 4.6 4.6 5.6 6.6 Approx RI 1.5 1.5 2.5 3.5 3.5 5.5 8 8 10 Groove Dim Dia

12、 I Radius H kO.l R k0.5 + 4.2 32 I u* :-: I : This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 02000 International Truck and Engine Corporation. SEPTEMBER 2000 Page 2 of 2 Copyright International Truck and Engine Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-