INTERN CEMS G-5 PART IA-2008 Paint Part IA Product Finishing Requirements Includes Appendix《油漆 第IA部分 产品精加工要求 包含附录》.pdf

《INTERN CEMS G-5 PART IA-2008 Paint Part IA Product Finishing Requirements Includes Appendix《油漆 第IA部分 产品精加工要求 包含附录》.pdf》由会员分享，可在线阅读，更多相关《INTERN CEMS G-5 PART IA-2008 Paint Part IA Product Finishing Requirements Includes Appendix《油漆 第IA部分 产品精加工要求 包含附录》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、NAVISTAR, INC. CEMS (CORPORATE ENGINEERING MATERIAL SPECIFICATION) NUMBER: CEMS G-5, Part IA TITLE: Paint Part IA , Product Finishing Requirements CURRENT ISSUE DATE: June 2008 WRITTEN/REVIEWED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE OF: October 2006 PRINTED COP

2、IES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health

3、practices and to determine the applicability of regulatory limits prior to use. Change Notice: Correction to Table I salt spray requirements for Class B; replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; editorial changes. 1.0 SCOPE The intent of th

4、is specification is to establish acceptable durability and quality levels for the finish on Navistar products and to define requirements and physical properties of the various materials used in the painting operation. 1.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied

5、 to the requirements of this specification must comply ith the requirements of the CEMS B-50 specification. w2.0 INTRODUCTION CEMS G-5 is divided into eight parts as follows: Part IA - Product Finishing Requirements Part V - Primers Part IB - Paint Material Requirements Part VI - Paints for Repair a

6、nd Service Part II - Topcoats Part VII - Deleted Part III - Chassis, and Miscellaneous Paints Part VIII - Engine Paints Part IV - Casting Sealers Part IA - Outlines classes of finish for Navistar parts, components, and products. It defines requirements and describes physical properties, which govern

7、 durability, corrosion protection, and overall appearance quality. Part IB - Outlines the procedure for specifying paint materials covered in the CEMS G-5 specification. Parts II thru VIII - Details specific liquid properties and dry film requirements for all paint materials used by the Company. The

8、 dry film requirements described in these seven sections apply to painted test panels evaluated under laboratory conditions. This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume al

9、l patent liability. 2008 by Navistar, Inc. JUNE 2008 Page 1 of 5 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TITLE: CURRENT ISSUE DATE: CEMS G-5, Part IA Paint - Produ

10、ct Finishing Requirements June 2008 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. PART IA - PRODUCT FINISHING REQUIREMENTS 3.0 C

11、ONTENTS PAGE REFERENCE DOCUMENTS 2 GENERAL REQUIREMENTS 2 QUALITY 4METHODS OF TEST 4 SOURCE APPROVAL AND QUALITY CONTROL 4 DESIGNATION ON DRAWINGS AND PURCHASE ORDERS 5 4.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standar

12、ds, specifications and regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 NAVISTAR CEMS GT-6B ASTM D 4138 NAVISTAR Manufacturing Standard MS-D-13 NAVISTAR CEMS GT-7D ASTM D 1729 CFR Title 29, Part 1910 NAVISTAR CEMS GT-7E SAE J2334 NAVISTAR CEMS B-50 NAVIS

13、TAR CEMS GT-23 SSPC-VIS-2 NAVISTAR CEMS GT-4D NAVISTAR CEMS GT-29 NAVISTAR CEMS GT-5A ASTM D 1186 5.0 CLASSIFICATION Paint grades are classified by chemical composition, durability and application. 5.1 Class of FinishThe Class of finish for specific products will be established by appropriate design

14、 engineering personnel in conjunction with the Industrial Design and Materials Engineering Groups. This specification will form the basis for uniform inspection standards for both manufactured and purchased parts. All materials utilized must conform to the requirements for the appropriate Class and

15、Grade for the finish specified. All deviations from this specification must be approved by the appropriate Materials Engineering Department. 6.0 GENERAL REQUIREMENTSThis specification is not intended to limit or specify the metal pretreatment or painting process but note that iron phosphate is not r

16、ecommended for zinc or aluminum coated substrates. When a chemical surface pretreatment is required, any process such as zinc or iron phosphate, acid wash prime or conversion coating applied by spray, immersion, or steam cleaning which results in finished parts meeting the requirements of this speci

17、fication will be approved. However, all systems from new vendors or deviations to this specification or changes in currently approved systems must be approved by Materials Engineering. 6.1 Finish RequirementsAll parts, whether painted by Navistar or purchased, will be finished with paints which meet

18、 all dry film requirements of the CEMS G-5 grade specified unless otherwise designated on the part drawing or purchase order. The resultant coating must match the appropriate Navistar color standard as well as meet ll of the requirements for the appropriate finish classification as shown in Table I.

19、 aJUNE 2008 Page 2 of 5 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TITLE: CURRENT ISSUE DATE: CEMS G-5, Part IA Paint - Product Finishing Requirements June 2008 This

20、document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 Page 3 of 5 TABLE I - FINISH CLASSIFICATION(1)AND REQUIREMENTS FOR PAINTED PA

21、RTS Class A(C(2) ) Class B Class D Class E Class F Class G Part/Finish Classification Decorative Nondecorative and Small Part Interior Frame and Chassis Engine (4 )Castings (4)SURFACE PREPARATION Coating Type Zinc Phosphate (Immersion or Spray) System, or Conversion Coating Solvent Wipe Shot or grit

22、 Blast Ferrous Coating Weight, mg/ft2200-400 for Zinc Immersion Systems 170-250 for Zinc Spray Systems - - Metal Non Ferrous Coating Weight, mg/ft2150-250 for Zinc Immersion Systems 75-150 for Zinc Spray Systems - - Nonmetal Preparation per accepted industry standards - PRIMER m 20 (3)20 (3)20 (3)15

23、 25 25 Ferrous Film Thickness, min mil 0.8(3)0.8 (3)0.8 (3)0.6 1.0 1.0 m 15 (3)15 (315 (315 25 25 Metal Non Ferrous Film Thickness, min mil 0.6 (3)0.6 (3)0.6 (3)0.6 1.0 1.0 m 25 - - - - - Nonmetal Film Thickness, min mil 1.0 - - - - - Hours 500 250 250 100 100 (9)mm 0.8 1.5 - 1.5 1.5 Salt Spray Corr

24、osion Creepage, max inch 0.03 0.06 - 0.06 0.06 - Humidity, Hours, Pass 500 250 100 250 100 100 Cycles 60 30 mm 0.8 1.5 Cyclic Corrosion Corrosion Creepage, max inch 0.03 0.06 - - - - Orange Peel, Min (5 )7 - - - - - Gloss - 5-25 5-25 Adhesion, % 90 90 90 90 90 90 Hardness HB HB HB HB H B TOP COATS F

25、ilm Thickness, min. unless specified as a range, mil (m) 1.7-9.5 (43-241) (6 ) (7 )1.5 (38) 1.0 (25) 1.0 (25) - Initial Gloss 20, min unless otherwise specified 80 As Specified - Hardness, min HB HB B B - Adhesion, % min 90 90 90 90 - Hours 500 - 250 100 mm 0.8 - 1.5 1.5 - Salt Spray Exposure Corros

26、ion Creepage, max inch 0.03 - 0.06 0.06 - Humidity, Hours, Pass 500 100 250 100 - Cycles 60 mm 0.8 Cyclic Corrosion Exposure Corrosion Creepage, max inch 0.03 - - - - Color Match International Standard Orange Peel Reflected Light, Min (8)6.0 - - - - Humidity, Hours, Pass 500 100 - - - (footnotes nex

27、t page) (1)See Appendix - General Information for cross reference to TMS-9009 Finish Classification. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TITLE: CURRENT ISSUE D

28、ATE: CEMS G-5, Part IA Paint - Product Finishing Requirements June 2008 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. (2)Class C

29、 is obsolete. Parts, such as bumpers, wheels, hubcaps, etc., formerly designated as Truck Group Class C finish, and all existing drawings, blueprints, purchase orders, etc., which specify Class C finish will meet the requirements of Class A finish. Class C finish will not be used on new drawings and

30、/or part releases. (3)Minimum film thickness for cathodic E-Coat primer, is 0.8 mils (20m) for steel, 0.6 mils (15m) for aluminum. (4)Class F - Primers used for Class F and Class G must be compatible for recoating with Grades -81H and/or -81W engine topcoats. (5)Comparison test: Orange peel comparis

31、on standards are available from Advanced Coatings Technologies, Inc., P.O. Box 401, 273 Industrial Drive, Hillsdale, MI 49242 (6)Minimum film thickness requirements for BC/CC are: Base Coat 0.8 mils (20 m); clear coat 1.5 mils (38 m). Basecoat must pass black/gray Morest hiding. (7)For painted wheel

32、s - top coat film thickness will not exceed 2.3 mils (58 m). (8)See International CEMS GT-29. (9)Test on as-cast parts prior to machining. Castings are not to be scribed and will be rated visually per SSPC-VIS- 2, controlled by the Society for Protective Coatings, to assign the appropriate “Rust Gra

33、de and Distribution“. A minimum rating of Grade 7 is required. 7.0 QUALITYAll painted surfaces will be free from sags, runs, dirt, seediness, orange peel, dry spray, dents, scratches, pits, gouges, and weld spatter when viewed with the unaided eye. The supplier should be capable of providing statist

34、ical evidence that products supplied to the requirements of this specification have been produced using manufacturing processes which are in statistical control and are competent to meet the requirements of this specification. The purchaser may request results of the suppliers quality control tests

35、on each shipment. 8.0 METHODS OF TESTS Unless otherwise specified, tests will be run in accordance with the following test procedures except the finished part or sections of the finished part, are to be used in place of the test panels. Test Procedure* Hardness CEMS GT-4DGloss CEMS GT-6BOrange Peel,

36、 Reflected Light CEMS GT-29 Salt Spray CEMS GT-7D/ASTM B117 Cyclic Corrosion CEMS GT-7D/SAE J2334 Humidity CEMS GT-7EAdhesion CEMS GT-5AColor ASTM D 1729 Phosphate Coating Wt. CEMS GT-23 Non-Destructive ASTM D 1186 Film Thickness Destructive ASTM D 4138 *Copies of Navistar CEMS GT test methods must

37、be purchased from Information Handling Services (IHS), 15 Inverness Way East, Englewood, CO 80112 (1-800-854-7179; or internet http:/ ). ASTM Test Methods are available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103 (or http:/www.astm.org) JUNE 2008 Page 4

38、of 5 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TITLE: CURRENT ISSUE DATE: CEMS G-5, Part IA Paint - Product Finishing Requirements June 2008 This document is restric

39、ted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. 9.0 SOURCE APPROVAL AND QUALITY CONTROL9.1 Supplier RequirementsAll suppliers to NAVISTAR are required to

40、be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited reg

41、istrar and must furnish copies of registration certificates to their Corporate Buyer upon request. 9.2 ApprovalParts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples, which were approved by the purchaser. No changes in formu

42、lation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, Truck Development and Technology Center and Purchasin

43、g and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for chang

44、e. 9.3 Process ControlThe supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all

45、required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using International plant may determine testing and reporting requirements on specific products. 10.0 DESIGNATION OF DRAWINGS AND PURCHASE ORDERSFinishing requirements on drawings and purchase

46、 orders will include color and finish class. Examples: FINISH: NAV 0311 Orange, Class B, CEMS G-5, Part IA. FINISH: NAV 0001 Black, Class F, CEMS G-5, Part IA. 11.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase c

47、ontrolled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN Information Handling Service (IHS) 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-85

48、4-7179 E-mail: AutomotiveIHS.com Website: http:/JUNE 2008 Page 5 of 5 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NAVISTAR, INC. CEMS (CORPORATE ENGINEERING MATERIAL SPECIFICATION)N