GSA OO-S-236 D-1989 SAW CIRCULAR TABLE TYPE WOODWORKING SINGLE TILTING ARBOR FLOOR MOUNTED《地板安装单轴心轮旋木工桌式圆锯》.pdf

《GSA OO-S-236 D-1989 SAW CIRCULAR TABLE TYPE WOODWORKING SINGLE TILTING ARBOR FLOOR MOUNTED《地板安装单轴心轮旋木工桌式圆锯》.pdf》由会员分享，可在线阅读，更多相关《GSA OO-S-236 D-1989 SAW CIRCULAR TABLE TYPE WOODWORKING SINGLE TILTING ARBOR FLOOR MOUNTED《地板安装单轴心轮旋木工桌式圆锯》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、m -G -O 9 00-S-23bD 32 7777774 002L)9L9 b O0 -S - 236D 10 February 1989 SUPERSEDING 31 MARCH 1975 O0 - S - 236C FEDERAL SPECIFICATION SAW, CIRCULAR, TABLE TYPE, WOODWORKING, SINGLE TILTING ARBOR, FLOOR MOUNTED This specification is approved by the Commissioner, Federal Supply Service, General Servic

2、es Administration, for the use of all General agencies. 1. SCOPE AND CLASSIFICATION 1.1 ScoDe. This specification covers electric motor driven, tilting arbor, table type, circular saws. 1.2 Classification. 1.2.1 Twes and sizes. The saw shall be of the following types and sizes as s,pecified (see 6.2

3、). Type I - Direct driven tilting arbor - Size 12 14 16 18 20 Saw bl ade 12 14 16 18 20 Type II - Belt driven tilting saw arbor Size 10 12 14 Saw bl ade diameter, inches -y., 10 12 14 FSC 3220 DISTRIBUTION STATEMENT A. Approved for pub1 ic release; distribution is un1 imited, THIS DOCUMENT CONTAINS

4、/? PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- ._ 00-S-23bD 32 W 7777974 0024920 2 0 00-S-236D 2 APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, and handbooks

5、form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the c solicitation (see 6.2). standards, F

6、ederal Requl at i on : U Occupational Safety and Health (OSHA) 29 CFR 1910 (The Code of Federal Regulations (CFR) and the Federal Register (FR) are for sale on subscription basic by the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. When reinstated, reprints of c

7、ertain regulations may be obtained from the Federal agency responsible for issuance thereof. ) Copies of OSHA standard and the standards which are incorporated by reference may be examined at the National Office of the Occupational Safety and Health Administration, U.S. Department of Labor, Washingt

8、on, DC 20210. Federal Standards: FED-STD-H28 - Screw Thread Standards for Federal Services. (Single copies of this specification and other Federal specifications and commercial item descriptions required by activities outside the Federal Government for bidding purposes are avai 1 ab1 e without charg

9、e from General Services Administration Business Service Centers in Boston, MA; Chicago, IL; Kansas City, MO; Fort Worth, TX; Houston; Denver, CO; San Francisco, CA; Los Angeles, CA; and Seattle, WA.) (Federal Government activities may obtain copies of Federal standardization documents and the Index

10、of Federal Specifications, Standard, and Commercial Item Descriptions from established distribution points in their agencies.) Military Specification: MIL-M-18058, - Machinery, Metal and Woodworking, Packaging of. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

11、 from IHS-,-,-00-S-236D Mi 1 i tarv Standards: MIL-STD-461 - Electromagnetic Emission and Susceptibility Requirements for the Control of Electromagnetic Interferences. MIL-STD-462 - Electromagnetic Interference Characteristics, Measurement of. (Unless otherwise indicated, copies of Federal and milit

12、ary specifications, and handbooks are avai 1 ab1 e from the Naval Pub1 i cations and Forms standards , Center, (ATTN: NPODS) , 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Other Government documents, drawinss, and publications. The follow- ing other Government documents, drawings, and publ

13、ications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. CODE OF FEDERAL REGULATIONS (CFR) U. S. DEPARTMENT OF LABOR, OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) 29 CRF 1910 - Occupational Safety and He

14、alth Standards. (Application for copies should be addressed to the Superintendent of Documents, U. S, Government Printing Office, Washington, DC 20402-0001.) (Copies of specifications, standards, handbooks, drawings, publications, and other Government documents required by contractors in connection

15、with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Non-Government pub1 ications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the doc

16、uments which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not listed in the DODISS-e the issues of the documents cited in the solicitation (see.6.2). Unless otherwise specified, AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI 01.1 -

17、 Safety Requirements for Woodworking Machinery. (DOD adopted) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-S-23bD 32 W 7777774 0024722 b II 00-S-236D (Application for copies should be addressed to the American National Standards Institute, AT

18、TN: Sales Dept., 1430 Broadway, New York, NY 10018-3363. ) NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) NEMA MG 1 - Motors and Generators. (DOD adopted) NEMA ICs 1 - Industrial Control and Systems. (DOD adopted) NEMA ICs 6 - Enclosures for Industrial Controls and Systems. (DOD adopted) (Appl

19、ication for copies should be addressed to the National Electrical Manufacturers Association, 2101 L Street, N.W., Washington, DC 20037-1580.) (Non-Government standards and other publications are normally available from the organizations that prepare or distri bute the documents. These documents also

20、 may be available in or through libraries or other informational servi ces. ) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes appl icable 1

21、 aws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.4. 3.2 Desiqn. The saw shall be new (not a prototype) and one of the manufacturers c

22、urrent production models capable of operations in accordance with the requirements herein. The saw shall include all components, parts, and features necessary to meet the performance requirements specified herein, All parts subject to wear, breakage, or distortion shall be readily accessible for adj

23、ustment, replacement, and repair. 3.2.1 Measurinq and indicatinq device calibrations. Measuring and indicating devices shall be graduated in inch-pound (see 6.4.1), metric (see 6.4.2), or dual (inch-pound and metric) units as specified by the procuring activity (see 6.2). all measuring and indicatin

24、g devices on the saw shall be graduated in the same system. Regardless of the measurement system used, 3.2.1.1 Dials. All dials used to indicate machine axes position or tool movement shall be graduated in increments not larger than .O25 inch. Dial and handwheel circumferences shall be permanently a

25、nd legibly engraved or etched on a nonglare background with graduations that can be read from the operators normal position. All feed dials shall have independent zero adjustments and 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I I I I o I I

26、I I l I I I I I I l I l l l ld) I I I I L I I I I I I I I I I I I -. t I I 00-S-23bD 32 7777374 0024723 00-S-236D shall be calibrated in such a manner that the last dial graduation progresses into and is continuous with the first dial graduation as the dial is rotated through the zero position. 3.2.

27、2 Recl aimed materi al s. The machine may contain recl aimed materi al s to the maximum extent possible provided such materials will not jeopardize the intended use, performance, or design life of the machine. Reclaimed materials shall have been collected or recovered from solid waste and reprocesse

28、d to become a source of raw materials, as opposed to virgin raw materials. None of the above shall be interpreted to mean that the used or rebuilt products are allowed under this specification. 3.2.3 Enerw efficiency. The saw and its components that directly consume energy in normal operation shall

29、be designed and constructed for energy efficiency as governed by the developments available within the industry. 3.2.4 Controls. All mechanical, hydraulic, and pneumatic operating controls shall be located convenient to the operators work station(s). 3.2.5 Safetv and health requirements. All parts,

30、components, mechanisms, and assemblies furnished on the saw, whether or not specifically required herein, shall conform to all requirements of OSHA 29 CFR 1910 and ANSI 01.1. If a conflict arises between 29 CFR 1910 and ANSI 01.1, 29 CFR 1910 shall apply. Additional safety and health requirements sh

31、all be as specified (see 6.2). Covers, guards, or other safety devices normally furnished as standard on the manufacturers commercial saw supplied to the commercial market shall be provided for the point of operation and all other parts of the saw that present safety hazards. Additional guarding dep

32、endent on workpiece size and configuration shall be provided when specified and fully described by the procuring activity (see 6.2). 3.2.6 Mercury restriction. The saw shall not contain mercury or mercury compounds nor be exposed to free mercury during manufacture. 3.2.7 Asbestosrestriction. Asbesto

33、s and materials containing asbestos shall not be used on or in the saw. 3.2.8 Environmental protection. During operation,service, transportation, or storage of the machine, it shall not emit materials hazardous to the ecological system as prohibited by Federal, state, or local statutes in effect at

34、the point of installation. 3.2.9 Lubrication. Means shall be provided to ensure adequate lubrication for all moving parts. Recirculating lubrication systems shall include a filter which is cleanable or replaceable and shall have a low lubrication level warning light that ia in clear view of the oper

35、ators normal work station. An automatic lubrication system shall be provided for all ways and 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-OO-S-236D 32 7977774 002472L1 T E 00-S-236D axis screws. Each lubricant reservoir shall have at least a 24

36、 hour capacity and means for determining fluid level. All oil holes, grease fittings, and filler caps shall be readily accessible. 3.2.10 Interchanqeabi 1 i tv. To provide for rep1 acement of worn parts, al 1 parts shall be manufactured to definite dimensions and tolerances that will permit installa

37、tion of replacement parts without modification of the part or machi ne. 3.3 Construction. The saw shall be constructed of parts which are new, without defects, and free of repairs. The structure shall withstand all forces encountered during operation of the saw to its maximum rating and capacity wit

38、hout permanent distortion. 3.3.1 Castinss and forqinqs. All castings and forgings shall be free of defects, scale, and mismatching. No processes such as welding, peening, plugging, or filling with solder or paste shall be used for reclaiming any defective part. Such processes may be used only for en

39、hancing surface finish and appearance. 3.3.2 Fasteninq devices. AI1 fasteners shall be installed to prevent Fastening devices subject to removal or adjustment shall change of tightness. not be permanently instal 1 ed. 3.3.3 Surfaces. All surfaces shall be clean and free of harmful or extraneous mate

40、rials. All edges shall be either rounded or beveled unless sharpness is required to perform a necessary function. Except as otherwise specified herein, the condition and finish of all surfaces shall be in accordance with the manufacturers commercial practice. 3.3.4 Weldinq, brazinq, or solderinq. We

41、lding, brazing, or soldering shall be employed only where specified in the original design. None of these operations shall be employed as a repair measure for any defective part. 3.3.5 Paintinq, Unless otherwise specified (see 6.2), the saw shall be painted in accordance with the manufacturers comme

42、rcial practice and color. 3.3.6 Threads. All threaded parts used on the saw and its related attachments and accessories shall conform to FED-STD-H28 and the applicable “Detailed Standard“ section referenced therein. 3.3.7 Electromaqnetic interference control. When specified (see 6.2), equipment furn

43、ished under this specification shall comply with MIL-STD-461, The equipment and subsystem(s) class and the emission and susceptibility requirements shall be as specified. 3.4 Components, Saws covered herein shall consist of a frame supporting driven system, the saw blade arbor and its elevating and

44、tilting mechanisms, 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-t 1 I I I t I I I i I I I I l l I I l I , I I l I l I l l l I I 1 I l l l I I I ! i I t ble, and herein. W 7779974 002Li325 1 I 00-S-236D 00-S-23bD 32 ich other compon ts necessary

45、 to me t the requirements stat d 3.4.1 Frame. The frame shall have sufficient strength and rigidity to support the working parts of the saw. The frame shall support and maintain alignment of the arbor with the table and provide both vertical and tilting arbor adjustments in relation to the workpiece

46、 support surface of the table. The frame shall have provisions on its base for attaching to the floor or foundation. The frame of type 1 saws shall allow disposal of sawdust and chips through and exhaust outlet shaped for connection to a pneumatic conveyor system. Type II saw frames shall include a

47、clean-out door for sawdust and chip removal. 3.4.2 Table. The stationary table shall be mounted to the frame, providing a horizontal workpiece support surface 3 feet, +/- 2 inches above the frame base mounting surface. The table top surface shall be flat within 0.005 inch per foot and have a finish

48、not rougher than 65 microinches. The table shall be fitted with removable throat plates or other provisions, as necessary, to limit side clearances on each side of the saw blade to x inch or less, and facilitate mounting of arbor attachments. The table shall have parallel slots on each side of the s

49、aw blade to accept a miter attachment. The slots shall span the complete table length and be parallel to the sides of the saw blade within 0.005 inch per foot. Each table shall have a linear scale graduated in increments not grater than 1/16 inch. Each quarter inch scale graduation shall be longer than the others and each inch graduation shall be numbered. The scale shall indicate the distance between the saw blade side and the face of the fence.