GSA A-A-1684 C-1997 TAPE PRESSURE-SENSITIVE ADHESIVE (PLASTIC FILM)《压敏胶粘带(塑料膜)》.pdf

《GSA A-A-1684 C-1997 TAPE PRESSURE-SENSITIVE ADHESIVE (PLASTIC FILM)《压敏胶粘带(塑料膜)》.pdf》由会员分享，可在线阅读，更多相关《GSA A-A-1684 C-1997 TAPE PRESSURE-SENSITIVE ADHESIVE (PLASTIC FILM)《压敏胶粘带(塑料膜)》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-bh8YC D 9999974 O375530 a72 D Metric July 24. 1997 Superseding December 21, 1990 A-A-1684C A-A- 1684B COMMERCIAL ITEM DESCRIPTION (PLASTIC FILM) TAPE, PRESSURE-SENSITIVE ADHESIVE The General Services Administration has authorized the use of this commercial item description by all Federal agencie

2、s. 1. ScoDe: This Commercial Item Description covers tape intended for labeling attachment and covering closure and sealing of interior and exterior domestic containers. 2. Salient Characteristics: - 2.1 The tape shall have a backing consisting of a transparent plastic film, and shall be coated on o

3、ne side with a water insoluble adhesive. Tape shall be sufficiently transparent to allow for easy reading of 10 point type, when tape is applied directly over it. 2.2 The tape shall conform with the requirements specified herein and in accordance with Table 1. 2.3 Workmanshim The tape shall be unifo

4、rmly constructed and free from defects which may impair usefulness of the material for the intended use. The adhesive shall be coated in a smooth uniform layer over the entire surface of one side of the tape backing. The tape shall be evenly and tightly wound with no voids. The edges of the roll sha

5、ll be clean cut. When unwound, the tape shall not tear nor shall the adhesive separate from the backing. 3. Remlatorv Reauirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regula

6、tion (FAR). Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to General Services Administration, Federal Supply Service, Engineering Branch, 26 Federal Plaza, New York, NY 10278. FSC 7510 Licensed by Informat

7、ion Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-lb84C M 9999974 0175531 TO9 350.3 N/100 mm (20 lbs./in) A-A-1 684C ASTM D 3759 Table 1. Physical Properties Adhesion (0z.h.) width (min.) Holding Power hours, minimum Tensile (1

8、bs.h.) width (min.) (24 hours) ASTM D 3654 Procedure A* *Standard Reference Material 1 8 1 Oa 4. Oualitv Assurance Reauirements: 4.1 Product Conformance. The product shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, sta

9、ndards and quality assurance practices and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 4.2 Testinp. Testing shall be in accordance with ASTM D 3715 Section 6 with an AQL of 4 percent defective. The sample unit

10、 shall be one roll of tape. 5. Packahe: Preservation, packing and marking shall be specified in the contract or order. 6. Notes: 6.1 Source of Documents. The following documents form a part of the Commercial Item Description to the extent specified herein. Unless otherwise indicated, the issue in ef

11、fect on the date of invitation for bids or request for proposal shall apply: 6.1.1 American Society for Testing and Materials (ASTM) standard test methods can be obtained from, 100 Barr Harbor Dr., West Conshohocken, PA 19428-2959. 6.1.2 Federal Acquisition Regulation (FAR) may be obtained from the

12、Superintendent of Documents, Government Printing Office, Washington, DC 20402. 6.1.3 Standard Reference Material is available from the National Institute of Standards and Technology; office of Standard Reference Materials; Room 204; Building 202; Gaithersberg, MD 20899. -2- Provided by IHSNot for Re

13、saleNo reproduction or networking permitted without license from IHS-,-,-A-A-Lb84C 9999974 0175532 945 A-A-1684C 6.2 OrderinP Data: Purchasers should select the preferred options permitted herein, and include the following information in procurement documents: A - Purchaser should specie the width a

14、nd length of tape desired. 6.3 National Stock Number Listing (NSN. The following is a list of NSNs assigned which correspond to this CID. The list may not be indicative of all possible NSNs associated with the CID. 75 10-00-073-6094 75 10-00-073-6095 75 10-00-073-6096 75 10-00-995-0455 MILITARY INTEREST: NONE: DoD has no registered interest in revisions and amendments to this Commercial Item Description until f3rther notice. Preparing Activity: GSA-FSS -3- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-