GSA A-A-1341 A-2002 WRENCH BOX STUD END TYPE STRAIGHT HANDLE《螺栓端头型弯头柄套筒扳手》.pdf

《GSA A-A-1341 A-2002 WRENCH BOX STUD END TYPE STRAIGHT HANDLE《螺栓端头型弯头柄套筒扳手》.pdf》由会员分享，可在线阅读，更多相关《GSA A-A-1341 A-2002 WRENCH BOX STUD END TYPE STRAIGHT HANDLE《螺栓端头型弯头柄套筒扳手》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、I IA-A-1341AFebruarv 5,2002SUPERSEDINGA-A-1341January 14, 1980COMMERCIAL ITEM DESCRIPTIONWRENCH, BOX, STUB END TYPE, STRAIGHT HANDLEThe General Services Administration has authorized the use of this commercial item descriptionby all. federal agencies.1. SCOPE. This commercial item description covers

2、 wrenches suitable for heavy duty nut turning onhexagon nuts.2. CLASSIFICATION. Not applicable3. SALIENT CHAFL4CTERISTICS.3.1 Design. Wrench openings shall be of a double hexagon (12 point) design. The handle shall afford awell-proportioned, comfortable handgrip. Wrench dimensions and sizes shall co

3、nform to Section 3.2.OPTIONAL r-ElBeneficial comments, recommendations, additions, deletions, clarifications, etc. and any other datawhich may improve this document should be sent to: General Services Administration, FederalSupply Service, Hardware SuperStore (6FEE), 1500 E. Bannister Rd Bldg. #6, K

4、ansas City,Missouri 64131.FSC 5120Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1341A3.2 Dimensions and Sizes.Centerline OfOutside Thickness Wrench Opening To Plunger ToWrench Diameter Of Wrench plunger (centerline stop (stop Diameter OveralI P

5、roofOpening Of Head Head To Centerline) Optional) Of Handle Length TorqueA BMax. Max Min Max Max. Min. Min.Inches Inches Inches Inches Inches Inches Inches Inches In-Lb.11-1/161-1/41-5/161-3/81-7/161-1/21-9/161-5/81-11/161-3/41-13/16,1-7/822-3/162-1/42-3/82-9/162-5/82-3/42-15/163-1/81-5/81-43/641-15

6、/162-1/162-3/322- 11/642-5/162-23/642-1/22-21/322-11/162-3/42-13/163-1/163-7/323-13/323-7/84-3/164-3/164-1/24-9/164-7/83/43147/87/87/815/161111-1/161-3/321-1/81-5/321-5/161-5/161-1 1/321-7/161-1/21-1/21-19/321-11/161-25/324-15/164-15/164-15/166-15/166-15/166-15/166-15/166-15/166-15/166-15/166-15/166

7、-15/166-15/166-15/166-15/1610-15/1610-9/1 610-9/1 610-9/1610-9/1 610-9/1610-9/167-5/167-5/168-1/168-5/168-9/168-13/169-1/169-9/1610-1/1610-3/1610-5/1 610-9/1610-13/1610-13/16il-1/1611-9/1611-9/1611-9/1611-9/1611-9/1611-9/1611-11/161-1/4 7/81-1/4 7/81-1/4 7/81-1/4 7181-1/4 7/81-1/4 7/81-1/4 7/81-1/4

8、7/81-1/4 11-1/4 11-1/4 11-1/4 11-1/4 11-1/4 11-1/4 11-1/4 15-1/4 1-1/85-1/4 1-1/85-1/4 1-1/85-1/4 1-1/85-1/4 1-1/85-1/4 1-1/87-13/167-13/167-15/161010-1/210-13/1611-1/1611-1/212-1/812-3/812-9/1612-13/1613-1/813-3/813-1/213-9/1613-11/1613-13/1613-13/1613-15/1614-1/166,1506,5007,2508,0009,0009,55010,4

9、5011,55011,75014,00018,00019.00029,00029,00029,00032,00035,00035,00040,00045,00014-3/16 48,0003.3 Materials. The materials used in the manufacturing of the wrenches shall be such as to producewrenches conforming to the physical requirements hereinafter described.3.4 Marking. Each wrench shall be mar

10、ked on one of the faces or on the handle as close to each head asis practicable in a plain and permanent manner. In addition to size markings, each wrench shall bemarked in a plain and permanent manner with the manufacturers name or trademark of such knowncharacter that the source of manufacture may

11、be readily determined.3.5 Hardness. Wrenches shall be treated to a Rockwell C hardness of not less that 38 nor more than 55when tested per ASTM-E-1 8. 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1341A3.6 Proof Torque. When tested as specifie

12、d in ASME-B 107.6, the wrenches shall withstand the prooftorque specified in Table 1 without failure or permanent deformation that might affect the durability orserviceability of the wrench.3.7 Wrench Opening. The nut and bolt head-engaging surfaces of the wrench shall be finished in asmooth and wel

13、l-defined manner. Tolerances shall be such as to insure acceptance when gaged withgages conforming to ASME B 107. 17M.3.8 Wrench Handle. Shall be of a stub end round design and suitable for accepting handle extension.The wrench handle shall be provided with a plunger stop to prevent handle extension

14、 from turning orslipping under normal working conditions. At the suppliers option, a stop maybe provided.3.9 Finish.3.9.1 Surface Finish. All surfaces shall be thoroughly cleaned,from burrs,pits, nodules, and other detrimentaldeficiencies.free from cracks, and essentially free3.9.2 Coatinm. The coat

15、ing shall be chrome plate (3.9.2.1) phosphate (3.9.2.2), oxide (3.9.2.3), oralternate coating (3.9.2.4) and shall be specified in the contractor order. The coating shall be adherent,smooth, continuous, and free from uncoated areas, pits, blisters, nodules, and imyother defects thatwould interfere wi

16、th their protective value and serviceability.3.9.2.1 Chrome Plate. Wrenches shall have a protective-decorative nickel-chromium plating. Thenickel thickness shall be a minimum of 0.000150 in. The chromium thickness shall be a minimum of0.000003 in. A nickel-iron undercoating(16% iron max.) may be sub

17、stituted for nickel.3.9.2.1. lChrome Plate Tests.One measurement of the thickness of each electroplated coating shall be conducted in accordance withany of the following, as appropriate, methods:ASTM B 487: Standard Method for Measurement of metal and oxide coating thickness bymicroscopical examinat

18、ion of a cross section.ASTM B 499: Standard Test Method for Measurement of coating thickness by the magnetic method:nonmagnetic coatings of magnetic basis metals.ASTM B 504: Standard Method for Measurement of thickness of metallic coatings by the coulometricmethod.ASTM B 530: StandardTest Method for

19、 Measurementof coating thicknessby the magnetic method:electrodeposited nickel coatings on magnetic andnonmagnetic substrates.ASTM B 568: Standard Test Method for Measurement of coating thickness by x-ray spectrometry.ASTM B 748: Standard Method for Measurement of thickness of metallic coatings by m

20、easurement ofcross section with a scanning electron microscope.ASTM A 754: Standard Test Method for Coating thickness by x-ray fluorescence.2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1341AVisible contact marks resulting from electroplating

21、operations shall be confined to the interior of the ,wrenching and drive openings. Surfaces of the electroplated tool shall be adherent, smooth, continuous,and free of visible defects, such as blisters, pits, roughness, cracks, and uncoated areas. Surfaces shallnot be stained or discolored and shall

22、 have a bright appearance. eThe electroplated tool shall be clean and free of darnage. The tool shall be tested for adhesion ofelectroplated materials in accordance with ASTM B571, Standard Test Methods for Adhesion ofMetallic Coatings, by one of the following methods: Grind-Saw, Push, File, or Burn

23、ishing.3.9.2.2 Phosphate. Wrenches shall have a chemically produced phosphate coating followed by a coatingof rust preventive.3.9.2.3 Oxide. Oxide coated wrenches shall have a coating consisting of a chemically produced oxidefollowed by a coating of rust preventive.3.9.2.4 Alternative Coatinm. Alter

24、nate coatings maybe used in lieu of nickel - chromium and shall besubjected to the Alternative Coating Test as specified below.3.9.2.4.1 Alternative Coating Test.Test Preparation. The quantity and condition of the wrenches used for the following testing shall be perthe manufacturers stdard practice

25、or as mutually agreed to by the manufactuer and- the GeneralServices Administration.Adhesion Test. Sample wrenches shall pass the file or grind-saw test of ASTM B 571,for qualitative adhesion testing of metallic coatings.Standard practiceAbrasion Test. Sample wrenches shall have no base material exp

26、osed after being subjecting to 100 litersof falling sand per ASTM D 968 Method A, Standard Test Method for abrasion resistance of organiccoatings by falling abrasive.Corrosion Test. The exterior surfaces of sample wrenches shall be tested for corrosion resistance byexposure to a 72-hour salt spray t

27、est, as specified in ASTM B 117, Operating salt spray (FOG)apparatus, without falling below the ASTM B 537, Standard practice for rating of electroplated panelssubjected to atmospheric exposure, rating of 6.4. REGULATORY REQUIREMENTS.4.1 Recovered Materials. The offeror/contractor is encouraged to u

28、se recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal acquisition Regulation(FAR).5. PRODUCT CONFORMANCE.5.1 Product Conformance. The product provided shall meet the salient characteristics of thisCommercial Item Description, conform to the produ

29、cers own drawing, specifications, standards, andquality assurance practices, and be the same product offered for sale in the commercial market. Thegovernment reserves the right to require proof of such conformance. a5.2 Responsibility for Inspection. Unless otherwise specified,performance of all ins

30、pection requirements and may use any4the contractor is responsible for thecommercial facilities (including theProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*A-A-1341At contractors own facilities) suitable for performance of the inspection requireme

31、nts, unless disapprovedby the Government. The Government reserves the right to perform any of the inspections deemed*necessary to assure the item conforms to the specified requirements.I 6. PACKAGING. Preservation, packaging and marking shall be as specified in the contractor order.I1. 7. NOTES. Thi

32、s section contains information of a general or explanatory nature that is not mandatory.7.1 Source of Documents.American Society of Mechanical Engineers (ASME), Manuel Gutierrez, Managing Director, 3 ParkAvenue, New York, NY 10016.American Society for Testing and Materials (ASTM), 100 Barr Harbor Dr

33、., W. Conshohocken, PA,19428-2959.Federal Acquisition Regulation (FAR): Government Printing OffIce, Superintendent of Documents,Washington DC. 20401-9371.7.2 Ordering data. Purchasers should select the preferred options permitted herein and should include thefollowing information in procurement docu

34、ments.a. Title, number, and date of Commercial Item Description.b. Wrench Opening.c. Type of coatingd. Packaging requirements.7.3 National Stock Numbers OWNS). A list of NSNs assigned that correspond to this CID. The listmay not be indicative of all possible NSNs associated with the CID.NSN Wrench O

35、peningi 120-00-288-9680 15120-00-288-8858 1-1/165120-00-288-9681 1-1/45120-00-288-9675 1-5/165120-00-541-1296 1-3/85120-00-541-1291 1-7/165120-00-293-0672 1-1/25120-00-541-1292 1-9/165120-00-541-1293 1-5/85120-00-174-1844 1-11/165120-00-293-0118 1-3/4NSN Wrench Opening5120-00-293-0119 1-13/165120-00

36、-293-1571 1-7/8 5120-00-287-4170 25120-00-541-1294 2-3/165120-00-541-1295 2-1/45120-00-293-1569 2-3/85120-00-293-0579 2-9/165120-00-293-0339 2-5/85120-00-293-0337 3-3/45120-00-293-0335 1-15/165120-00-204-2667 3-1/87.4 Key words. Wrench; Box, Stub End Type, Straight Handle.MILITARY INTERESTS:NONE: DoD has no registered interestain revisions and amendmentsto thisCommercial Item Description untilfi.u-thernotice.Preparing Activity:GSA-FSSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-