GMW GMW15681-2012 Tear Strip (Pull Cord) Testing Issue 2 English.pdf

《GMW GMW15681-2012 Tear Strip (Pull Cord) Testing Issue 2 English.pdf》由会员分享，可在线阅读，更多相关《GMW GMW15681-2012 Tear Strip (Pull Cord) Testing Issue 2 English.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW15681 Tear Strip (Pull Cord) Testing Copyright 2012 General Motors Company All Rights Reserved July 2012 Originating Department: North American Engineering Standards Page 1 of 5 1 Scope Note: Nothing in this standard supercedes applicable laws and r

2、egulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Purpose. This standard describes the methods to measure the force required to remove the tear strip (pull cord) from an extruded weatherstrip and to measure the ultim

3、ate force and elongation of the tear strip (pull cord). 1.2 Foreword. Not applicable. 1.3 Applicability. This test method is applicable to all body seals with tear strips (pull cords). 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Stand

4、ards/Specifications. ISO 7500 ISO 9513 2.2 GM Standards/Specifications. None 3 Resources 3.1 Facilities. Not applicable. 3.2 Equipment. 3.2.1 Test Machine. The test machine shall fulfill the following requirements: The force-measuring device of the test machine shall correspond to ISO 7500-1, Class

5、1; the deflection measuring device shall correspond to ISO 9513, Class 0.2. The test machine shall be such that the required test velocity can be maintained. 3.2.2 A 45 degree angle flange fixture (see Appendix A, Figure A1). 3.2.3 A sharp razor knife. 3.3 Test Vehicle/Test Piece. 3.3.1 Test Specime

6、ns. 3.3.1.1 Method A. Three test specimens, each 150 mm 1 mm in length, shall be cut from one continuous weatherstrip extrusion. 3.3.1.2 Method B. A weatherstrip extrusion, approximately 1 m in length, is required for testing the ultimate force and elongation at break of the tear strip (pull cord).

7、3.4 Test Time. Not applicable. 3.5 Test Required Information. Not applicable. 3.6 Personnel/Skills. Not applicable. 4 Procedure 4.1 Preparation. Not applicable. 4.2 Conditions. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or

8、networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15681 Copyright 2012 General Motors Company All Rights Reserved July 2012 Page 2 of 5 4.2.1 Environmental Conditions. The minimum time between manufacturing and testing shall be 72 h. The test pieces shall be mai

9、ntained at a temperature of 23 C 5 C and 50% 5% relative humidity for at least 24 h prior to test and shall be free from strain during this period. 4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component

10、drawings, test certificates, reports, etc. 4.3 Instructions. 4.3.1 Method A; 45 Degree Pull Test. 4.3.1.1 Using the three 150 mm 1 mm specimens, pull the tear strip (pull cord) approximately 50 mm from one end of each specimen. 4.3.1.2 Mount the weatherstrip on the 45 degree angle flange fixture. Pl

11、ace the pulled tear strip (pull cord) end into the upper grips of the tensile machine. Place the other end of the weatherstrip (fixture) in the lower grips. Run the pull test at a speed of 250 mm 5 mm/minute. 4.3.2 Method B; Ultimate Force and Elongation of Tear Strip. Required for non-reinforced co

12、rds only. 4.3.2.1 Remove the tear strip (pull cord) by hand from the 1 m long weatherstrip extrusion. 4.3.2.2 Cut the tear strip (pull cord) into six sections, each approximately 150 mm in length. Place each end of the section into the upper and lower grips of the tensile machine. Place an extensome

13、ter in the middle of the section to measure the percent elongation (see Appendix A, Figure A2). Pull each section at a speed of 500 mm 5 mm/minute. 5 Data 5.1 Calculations. Not applicable. 5.2 Interpretation of Results. Not applicable. 5.3 Test Documentation. With reference to this test procedure, t

14、he results shall be represented in a test report. The report shall include the following: Complete identification of the specimen. Conditioning of the test specimen. Test conditions. Any deviations to the test method. Peak values for the 45 degree angle pull (Method A). Ultimate Force (N). Percent (

15、%) elongation of each sample. 6 Safety This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health

16、 practices and determine the applicability of regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. Not applicable. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW15681 Copyri

17、ght General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15681 Copyright 2012 General Motors Company All Rights Reserved July 2012 Page 3 of 5 9 Release

18、 and Revisions This standard was originated in September 2007. It was first approved by the Global Elastomers Team in October 2007. It was first published in October 2007. Issue Publication Date Description (Organization) 1 OCT 2007 Initial publication. 2 JUL 2012 Five year refresh of standard. (Ela

19、stomers Global Subsystem Leadership Team) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15681 Copyright 2012 General Motors Company All

20、 Rights Reserved July 2012 Page 4 of 5 Appendix A Figure A1: 45 Degree Angle Flange Fixture Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS

21、GMW15681 Copyright 2012 General Motors Company All Rights Reserved July 2012 Page 5 of 5 Figure A2: Ultimate Force and Elongation Test Setup Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-