GMW GMW14390-2011 Durability Test of Exhaust Pipe Connections Issue 2 English《排气管连接的耐久性试验 第2次出版(英文版本)》.pdf

《GMW GMW14390-2011 Durability Test of Exhaust Pipe Connections Issue 2 English《排气管连接的耐久性试验 第2次出版(英文版本)》.pdf》由会员分享，可在线阅读，更多相关《GMW GMW14390-2011 Durability Test of Exhaust Pipe Connections Issue 2 English《排气管连接的耐久性试验 第2次出版(英文版本)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW14390 Durability Test of Exhaust Pipe Connections Copyright 2011 General Motors Company All Rights Reserved July 2011 Originating Department: GME Specification Center Page 1 of 5 1 Scope Note: Nothing in this standard supercedes applicable laws and

2、regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Purpose. Determination of the dynamic strength in a bench test. 1.2 Foreword. Not applicable. 1.3 Applicability. For all pipe connections of mufflers, catalytic conv

3、erters, diesel particulate filters and connecting flanges. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. None 2.3 Additional References. CTS/part drawing 3 Resources 3.1 Fa

4、cilities. Force controlled test bench with closed control loop, travel sensor and cycle counter. The test device shall be suitable for dynamic forces of (100 to 2000) N with regard to a test frequency range of (10 to 20) Hz (sine). The test facility shall have a valid ISO certificate which is noted

5、in a test report. 3.2 Equipment. 3.2.1 Peak Value Recorder. Peak Value Recorder to automatically record the oscillation amplitude, with automatic shut-off for the testing machine when the oscillation amplitude exceeds the adjusted limiting values. 3.2.2 Attachment of Test Piece. 3.2.2.1 Attachment o

6、f Flange. The flange shall be attached on a rigid fixing device without gasket with regard to bolted joint specified by drawing. The connection shall be such that pipe connection/welded joint of the flange is not impaired. The force application shall ensure the malleability of the pipe. The force sh

7、all be located according to paragraph 3.2.2.2. 3.2.2.2 Attachment of Mufflers, Catalytic Converters and Diesel Particulate Filters. The test piece shall be mounted such that the pipe connection is not impaired (see Figure 1). The force application shall ensure the malleability of the pipe. A link wi

8、th a U-joint at the ends shall be installed between load cell and force application. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW1439

9、0 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 2 of 5 Figure 1: Photo of Muffler 1 Base plates 2 Clamping claws 3 Force application 4 Universal clamping system 5 Force gauge 5 kN maximum S = Muffler clamping length S = 245 mm. A = Distance between bottom of pot and clampi

10、ng claw A = 65 mm. X = Lever arm measured from center of pipe welding joint to center of force application; X = 150 mm. Ma = The tightening torque of clamping claw shall be selected in such a way that the pot casing is neither deformed nor impaired. L = The length of force application measured from

11、load cell connection to the center of pipe connection shall be 150 mm minimum. 3.3 Test Vehicle/Test Piece. At least 5 new production parts shall be tested for each pipe connection / type. The parts shall be produced as specified by assembly drawing. The pipe length shall be 200 mm, however 300 mm m

12、easured from pipe welding joint. Pipe connections shall be extended with a pipe as specified by drawing, if necessary. To the correct lug-in depth, tightening torque of the production clip shall be ensured, in order to guarantee a defined rigidity at the connection point. Conditioning of parts, if a

13、pplicable, shall be taken from the CTS/part drawing. 3.4 Test Time. Not applicable. 3.5 Test Required Information. Not applicable. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-

14、,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14390 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 3 of 5 3.6 Personnel/Skills. Not applicable. 4 Procedure 4.1 Preparation. 4.1.1 Test Setup. The test setup shall be performed using the direction of force application determined f

15、rom the strain collectives for the respective vehicle type and motorization, which is indicated in the CTS/drawing specification. 4.2 Conditions. 4.2.1 Environmental Conditions. The test shall be performed at (+23 5) C ambient room temperature. 4.2.2 Test Conditions. Deviations from the requirements

16、 of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.3 Instructions. The strength test shall be performed as a single-step test. 4.3.1 Test torque, test frequency, cycles of failure (N 90%), and maximum permissi

17、ble dispersion (N 90% / N 10%) can be taken from the CTS/drawing specification. Mb = FP X in Nm = Test torque FP = Test force at test piece F = (FT + FP) = Test force at load cell, measured from load cell connection to pipe connection. At the dynamic test it is determined by the dynamic mass flow an

18、d shall be taken into account. FT = Inertia force of test device 4.3.2 Shut-off criterion at this test is the increase of the oscillation amplitude or test frequency which automatically shuts-off the testing machine as soon as the adjusted limiting values are exceeded. 4.3.3 The limiting values shal

19、l be 110% maximum of the actual amplitude measured at the beginning of the test. 4.3.4 If no first visible cracks occur, the test may be stopped at N 10 % value as specified by CTS/drawing specification. A test protocol according to Appendix A shall be used for recording of test data and results and

20、 shall be added to a test report after the test. 5 Data 5.1 Calculations. In order to obtain reliable results for the number of cycles to first visible cracks/fracture determined in the endurance strength range in comparison to the N 90% value required on CTS/drawing specification, it is necessary t

21、o evaluate them according to the statistical method of fatigue life probability to the logarithmic normal distribution. N 50%-value: N 50% = Xm N 10%-value: N 10% = N 50% 101.28 log S N 90%-value: N 90% = N 50% / 101.28 log S Period spread: Period spread = P90 % / P10 % Calculation of probabilities

22、shall be performed according to the following formulas, where no uncracked test pieces or outliers shall be included. 5.1.1 Mean Value. Xm = 10 dP m e gl h n = number of values Xi = crack period 5.1.2 Standard Deviation. S = 10 1n-1 (log Xi log Xm)2Copyright General Motors Company Provided by IHS un

23、der license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14390 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 4 of 5 5.2 Interpretation of Results. The results determined

24、shall be compared with the CTS/component drawing and evaluated accordingly. 5.3 Test Documentation. The test results shall be added to a test report as specified in paragraph 5.3.1 through 5.3.4 and paragraph 5.1. 5.3.1 Test Piece Description. Part name and number, development state, date of manufac

25、ture, drawing number, drawing date. 5.3.2 Summary of Test Results and Evaluation. Briefly evaluation of test results (OK, NOK), test specification and if required deviations, comparison of results with CTS/drawing specifications. 5.3.3 Test Description. Description of test bench with photograph, bri

26、ef description, description of used test set-up, calibration of testing equipment, initial cracking criterion and detection, load cell, force application mass measured from load cell connection, ISO certificate of test facility. 5.3.4 Documentation of Individual Results. Test load, travel amplitude

27、of test cylinder, test direction, test frequency, number of cycles for initial cracks, position and photograph of initial cracks, logarithmic characteristic data. At least one test piece shall be cut for each type in such a way, so that the interior structure can be recognized clearly. 6 Safety This

28、 standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability

29、of regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. CTS Component Technical Specification ISO International Organization for Standardization OK Approved or Endorsed NOK Not Approved or Endorsed VTS Vehicle Technical Specification 8

30、Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW14390 9 Release and Revisions This standard was originated in October 2005. It was first approved by Global Exhaust SSLT in November 2005. It was first published in November 2005. Issue Publica

31、tion Date Description (Organization) 1 NOV 2005 Initial publication. 2 JUL 2011 5 year refresh; transfer to new template. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WO

32、RLDWIDE ENGINEERING STANDARDS GMW14390 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 5 of 5 Appendix A A1 Durability Test of Exhaust Pipe Connections Order: Test specification: Part name: Test Building: Part No.: Test Facility: Drawing No.: Load Cell: Supplier: Test Bench:

33、 FT = Inertia force at test device in kN FP = Test force at test piece in kN as per specification F = actual test force at load cell in kN F = (FT + FP) FT = m s (6.28 f)2 / 106 in kN x mT in kg x s in mm x f in 1/s mT =.kg FT =kN Shut-off for testing machine travel amplitude% Shut-off for testing m

34、achine frequency violation.% Temperature conditioning after Force sensor calibrated on Test bench certificated on Test pieces marked Photograph test set-up Date Time Name Test No. Test torque Mb in Nm Test force F in N Lever arm X in mm Machine data in V Travel amplitude s in mm Test direction X/Y/Z

35、 Test side (Note 1) Test frequency f in Hz Initial cracks N in cycles Position of initial cracks (Photograph No. position of initial cracks) Note 1: E = Input, A = Output, L = left, R = right Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-