GMSA ETS DM 004-1997 LIGHT ALLOY WHEEL RIM IMPACT TEST.pdf

《GMSA ETS DM 004-1997 LIGHT ALLOY WHEEL RIM IMPACT TEST.pdf》由会员分享，可在线阅读，更多相关《GMSA ETS DM 004-1997 LIGHT ALLOY WHEEL RIM IMPACT TEST.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、STD-GMBRAZIL ETS*DM*004-ENGL 1797 m 7307507 0005b12 T3T m ENGINEERING TEST SPECIFICATION BRASIL PRODUCT ENGINEERING Light Alloy Wheel Rim Impact Test Teste de Impacto no Aro das Rodas de Alminio rlAME: Summary. 1 - Objective 2- Reference 3- General Conditions 4- Specific Conditions 5- Sketch of test

2、 fixture. 1- Objective . This specification stablishes parameters for light alloy wheel Rim impact Test, used in passanger and commercial vehicles. 2- References. a) The kinetic energy ( Joule) is equal the potential energy referenced in the equation: Pe = Ke = mgh m = Mass (kg) g = Acceleration due

3、 to gravity( m/s2) h = Distance“ height “between wheel rim and impact mass ( m ). b) The impact cylinder must be 120 mm long ,50 mm diameter and 40 +/- 3 Rockwell C hardness. 3-General conditions. a) Three (3) samples are used for the impact test. b) The impact test will be performed with kinetic en

4、ergy = 650 +/- 10 J. c) The impact of the cylinder should be centralized above the internal wheel rim, Sumrio. 1- Objetivo 2- Referncias 3- Condies Gerais 4- Condies Especificas 5- Croqui do dispositivo de teste. i - Objetivo Esta especificao estabelece os parmetros de ensaio para o teste de impacto

5、 no aro das Rodas de alminio utilizadas em veculos de passageiros e comerciais. 2- Referncias. a) A energia cintica de impacto ( Joule) e igual a energia potencial fomecida pela equao:. Ep = Ec = m.g.h. m = Massa (kg) g = Acelerao da gravidade ( m/s2) h = Altura entre aro da roda e a massa de impact

6、o (m). b) O cilindro de impacto deve ter 120 mm de comprimento e 50 mm de dimetro com dureza de 40 +/- 3 Rockwell C 3- Condies gerais. a) Para os ensaios de impacto sero utilizadas trs ( 3 ) amostras. b)O teste de impacto ser realizado com energia cinetica = 650 +/- 10 J. c) O cilindro de impacto de

7、ve estar centralizado no aro interno da roda, cpnforme mostrado no croqui. REV1 S 10 N: according to sketch. APPROVED BY:Nelson C.Pires Jr. TSFL1.wC COPYRIGHT GM do BrasilLicensed by Information Handling ServicesSTD-GMBRAZIL ETS-DM-004-ENGL 1997 7307509 0005613 97b PAGE: 2 Of 4 ETS -OM-004 3.1- Test

8、 equipment set up. a) The samples are assembled on devices . simulating the vehicle true assembling conion. b) Before starting the test all samples must be free from any cracks produced by the msrnufacturing process and must be dimensionally and metalurgicall y approved. 4. Specific Conditions. a) D

9、uring the test deformation of the whee! rim may occur. A crack less than or equal to 30 mm, or the sum of all small cracks not exceeding 30 mm are allowed. b) During the test no extraction of the material should occur. If this happens all wheels with identical characteristics will be not approved. 5

10、. Sketch of the test equipament 3.1- Preparao do equipamento de teste. a) As amostras so montadas ern dispositivo simulando a condio de montagem no veculo. b) Antes do inicio do teste as amostras no devero possuir nenhum indcio de trinca proveniente do processo de fabricao e devem estar dimensionalm

11、ente e com anlise metalurgica aprovadas. 4. Condie Especificas. a) Durante o ensaio deve ocorrer o amassamento da roda, sendo permitido uma trinca menor ou igual a 30 rnm ou o somatrio delas igual ou inferior a 30mm b) Durante o ensaio no pode ocorrer arrancamento de material ern hipotese alguma. Se

12、 isto vier a occorrer, todas as rodas com as mesmas caracteristicas esto reprovadas. 5.Croqui do equipamento de teste, IAITAC HMENT /ANEXC . REVISION COPYRIGHT GM do BrasilLicensed by Information Handling ServicesSTD-GMBRAZIL ETS*DM*OOLI-ENGL 1777 W 7307509 0005bLLI 802 PAGE: 3 of4 ETS -DM-004 I“) W

13、heel Massa (Mass) -r Cylinder REVISION COPYRIGHT GM do BrasilLicensed by Information Handling ServicesSTD-GMBRAZIL ETS*DM-004-ENGL 1997 7307507 0005b15 749 = - NUMBER: ENGINEERING TEST SPECIFICATION PRODUCT ENGINEERING 1 BRASIL I I I SPECIFICATION R PREPARED BY :ED RESPONSIBLE :ED APPROVED BY :NELSON C.PIRES JR. IREVISIONS DOCUMENT I DATE APPROVAL COPYRIGHT GM do BrasilLicensed by Information Handling Services