GMKOREA EDS-T-7024-2006 POLYURETHANE TUBING.pdf

《GMKOREA EDS-T-7024-2006 POLYURETHANE TUBING.pdf》由会员分享，可在线阅读，更多相关《GMKOREA EDS-T-7024-2006 POLYURETHANE TUBING.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、GM DAEWOO Auto & Technology EDS Engineering, GM DAEWOO Auto & Technology Standards POLYURETHANE TUBING EDS-T-7024 ISSUED DATE: 1995. 03. 14 REVISED DATE: 2006. 06. 19 VERSION: 4 EDS-T-7024POLYURETHANE TUBING PAGE: 1/3 ISSUED DATE: 1995. 03. 14 REVISED DATE: 2006. 06. 19 VERSION: 4 GM DAEWOO Auto & T

2、echnology 1. PURPOSE This specification covers the requirements for tubing used for fuel tank breathing and ventilation purposes. 2. SCOPE This specification applies to tube fuel filler material, polyurethane (PUR) elastomer, thermoplastic type, free from reclaimed material. 3. APPROVAL OF DELIVERY

3、3.1. Polyurethane tubing that is applied to this specification shall satisfy the requirement of clause 8 and approved by GMDAT TECHNICAL CENTER before bulk supplies are commenced. 3.2. Any change in material or processing shall require reapproval by GMDAT TECHNICAL CENTER. The supplier must accept s

4、ole responsibility for informing the purchaser of any such change, and of re-submitting samples for approval. 4. TEST PIECES 4.1. The number, size and dimensions of test pieces shall be as specified in the relevant test method for the property concerned. For the determination of the properties to cl

5、auses 8.5 to 8.8 suitable pieces cut from the component shall be used as test pieces. 4.2. For initial sample approval and arbitration purposes at least 3 test pieces shall be tested and for routine quality control purposes at least one test piece shall be tested. 5. CONDITIONING Test pieces shall n

6、ot be tested within 72 hours of manufacture. Prior to test, test pieces shall be conditioned as required by the appropriate test methods. 6. TEST MEDIA 6.1. Test fluid to EDS-T-7012 6.2. Engine oil approved by GMDAT TECHNICAL CENTER 6.3. Deionized water 7. APPARATUS Test apparatus as required by cla

7、use 8. EDS-T-7024POLYURETHANE TUBING PAGE: 2/3 ISSUED DATE: 1995. 03. 14 REVISED DATE: 2006. 06. 19 VERSION: 4 GM DAEWOO Auto & Technology 8. REQUIREMENTS DESIGNATIONS TEST METHODS REQUIREMENTS 8.1. Visual examination with naked eye (as received) - The interior of the tube shall be smooth and free f

8、rom any residue. 8.2. Density EDS-T-7406 (1.200.05) g/cm3 8.3. Hardness EDS-T-7403 (855) SHORE A or IRHD 8.4. Tensile Strength EDS-T-7408-dumb- bell test piece S1- Cross Head Speed : 100mm/min35 MPa min. 8.5. Temperature Resistance 8.5.1. High temperature aging - Visual examination immediately on re

9、moval from oven 8.5.2. Cold Resistance 8.5.3. High temperature aging - Visual examination immediately on removal from oven 8.5.4. The test from clauses 8.5.1 to 8.5.3 shall be performed on the same test piece and in the specified sequence. EDS-T-7421-A5- (605)minutes at 1052.5KEDS-T-7423-B2 Bend tes

10、t by bending test piece back through 180 on itself in the same place three times EDS-T-7421-A1- (+902.5K) Test piece shall not show any ovality or adhesion between the inner surfaces of the bore when pushed together. No breakage, cracking, permanent deformation. Same as clause 8.5.1 8.6. Fuel Resist

11、ance 8.6.1. Change of Volume EDS-T-7419-A 0 +50% 8.7. Resistance to Oil 8.7.1. Change of Mass EDS-T-7418-Engine oil-B3 0 +5% 8.8. Hydrolysis Resistance 8.8.1. Change of Hardness 8.8.2. Visual changes with naked eye. 8.8.3. Tensile Strength EDS-T-7418-deionzed water-J3-(+802.5K) Same as clause 8.4 Af

12、ter removal form water, test pieces shall be preconditioned at +232K, relative humidity (506)% for at least 48 hours 10 max. (Shore A or IRHD) No internal sickness or evidence of decomposition 30 MPa min. EDS-T-7024POLYURETHANE TUBING PAGE: 3/3 ISSUED DATE: 1995. 03. 14 REVISED DATE: 2006. 06. 19 VERSION: 4 GM DAEWOO Auto & Technology 9. ADDITIONAL REQUIREMENTS Other additional requirements may be specified on the relevant components drawings 10. CODING SYSTEM POLYURETHANE TUBING to EDS-T-7024 Test Method Designation 11. REFERENCE GME 08 002 (79.10) POLYURETHANE TUBING