GMKOREA EDS-A-1003-2008 DRAWING AND LAYOUT FORMS.pdf

《GMKOREA EDS-A-1003-2008 DRAWING AND LAYOUT FORMS.pdf》由会员分享，可在线阅读，更多相关《GMKOREA EDS-A-1003-2008 DRAWING AND LAYOUT FORMS.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、GM DAEWOO Auto & Technology EDS Engineering, GM DAEWOO Auto & Technology Standards DRAWING AND LAYOUT FORMS Do Not Use on New Programs. Being Replaced by Global Design Standards EDS-A-1003 ISSUED DATE: 1980. 08. 01 REVISED DATE: 2008. 05. 31 VERSION: 6 (Superceded) EDS-A-1003DRAWING AND LAYOUT FORMS

2、 PAGE: 1/6 ISSUED DATE: 1980. 08. 01 REVISED DATE: 2008. 05. 31 VERSION: 6 GM DAEWOO Auto & Technology Note: This standard may be applied only for current project drawings generated by CATIA. It is Superceded for all future projects and replaced by Global Design Standards. 1. PURPOSE This standard a

3、ims at standardizing forms of product drawings to permit easy copying, micro-filming and preservation of drawings. 2. SCOPE This standard specifies the form of product drawings. 3. SIZE OF DRAWINGS 3.1. A series size drawings Table 1. A series size drawings (Unit : mm) Nominations Widths Lengths A 4

4、 210 297 A 3 297 420 A 2 420 594 A 1 594 841 A 0 841 1189 Note 1. It is desirable not to use extended A series drawings as long as possible. When inevitable, follow clause 4 of KS B 0001. 3.2. Roll size drawings Table 2. Roll size drawings (Unit : mm) Nominations Widths Lengths R0 N 841 200N R4 N 12

5、0010 200N (1600 min.) (R8 N) 152010 200N (2000 min.) Notes 1. The length of drawings shall be multiples (N) of 200mm, and larger than the width. 2. It is desirable not to use dimensions shown in parenthesis in Table 2 as long as possible for convenience of reproduction and storage. EDS-A-1003DRAWING

6、 AND LAYOUT FORMS PAGE: 2/6 ISSUED DATE: 1980. 08. 01 REVISED DATE: 2008. 05. 31 VERSION: 6 GM DAEWOO Auto & Technology 4. DRAWING FORMAT 4.1. Title block and revision tables (Unit : mm) Drawing size/Dimension a b c d e f g h k l m n pA4 110 25 34 10 23 33 20 24 18 46 16 7 - A3, A2, A1 148 25 43 12

7、28 51 21.3 31.5 25.3 68.9 17 7 7A0 and Roll size 170 30 49 13 32 58 25 37 30 78 25 8 12Drawing size/Dimension q r s t u v w x y z Company nameA4 49 23 15 18 18 12 10 14 15 7 B-L/R-2.5 A3, A2, A1 69 33 15 18 18 12 10 14 15 7 B-L/R-4.0 A0 and Roll size 70 40 15 23 23 16 12 19 20 8 B-L/R-4.5 Remark: Si

8、ze of company name shall conform to the EDS-A-0040. Figure 1. Title block and revision tables ab c de f g h k lm n p q r stuvwxy zEDS-A-1003DRAWING AND LAYOUT FORMS PAGE: 3/6 ISSUED DATE: 1980. 08. 01 REVISED DATE: 2008. 05. 31 VERSION: 6 GM DAEWOO Auto & Technology 4.2. Frame All the product drawin

9、gs shall have the frame that divides the sheet into a drawing space and borders. 4.3. Centering mark To facilitate reproduction or micro-filming of drawings, a centering mark shall be put on each side of a drawing. (Unit : mm) Drawing size/ Dimension a b m Remark A 4 - A 3 5 A2, A1 5 A0 or more 7 7

10、0.6 Figure 2. Centering mark 4.4. Grid reference system For easy identification, the frame length and width is divided into several zones with specific dimensions. These zones are numbered horizontally and lettered vertically with uppercase letters from the lower right-hand corner, or 1, 2, 3. from

11、the right, and A, B, C., from the lower end 4.5. Frame connection line For micro-filming of roll drawings and connection of reproduced drawings, connection lines are drawn inside the lengthwise frame line. The space between adjacent connection lines is termed a frame. Figure 3. Frame connection line

12、 Centering markFrame Zone numberZoning lineBorder a mm b Frame connection line 2 20 EDS-A-1003DRAWING AND LAYOUT FORMS PAGE: 4/6 ISSUED DATE: 1980. 08. 01 REVISED DATE: 2008. 05. 31 VERSION: 6 GM DAEWOO Auto & Technology 4.6. Drawing number block (Unit : mm) Drawing size/Dimension a b c d RemarkA3,

13、A2, A1, 23 65 20 - A0, Roll size 23 90 20 20 Figure 4. Drawing number block 4.7. Company name Drawing size Size of logo type and symbol mark Remark A4, A3 B-L/R-5.0 A2 or more B-L/R-7.0 See EDS-A-0040 Figure 5. Company name 5. LETTER SIZE The letter size shall be regulated by the letter height as sh

14、own on Table 3. Table 3. Size of letter (Unit : mm) Divisions A4A1 A0 or more Drawing size (A4, A3. etc.) 7 Zone number, Release 3.5 5 Others 1.75 2.25 b c d a EDS-A-1003DRAWING AND LAYOUT FORMS PAGE: 5/6 ISSUED DATE: 1980. 08. 01 REVISED DATE: 2008. 05. 31 VERSION: 6 GM DAEWOO Auto & Technology (Un

15、it : mm) Drawing size/Dimension h L a b c d A 4 210 297 10 25 - - A 3 297 420 10 25 96 93 A 2 420 594 20 40 89 95 A 1 594 841 20 40 98 92 A 0 841 1189 20 40 94 100 Figure 6. A-series size drawing format 1 24B 6 3A C D 5 1 246 35 B A C D b Zoning line Zone No. Drawing No. Company name Frame Centering

16、 markTitle block Revision table c LL/2 a a a d h h/2 EDS-A-1003DRAWING AND LAYOUT FORMS PAGE: 6/6 ISSUED DATE: 1980. 08. 01 REVISED DATE: 2008. 05. 31 VERSION: 6 GM DAEWOO Auto & Technology 1. R0N, R4N size drawing format Note: Same as A-series size drawing format except for special notes. 2. R8N si

17、ze drawing format Note: Same as R0N, R4N size drawing format except for special notes. (Unit : mm) L2 Drawing size/Dimension h L1 Minimum Maximum RemarkR0 N 841 1100 1100 R4 N 120010 800 800 R8 N 152010 1100 L1 / 2 1100 Figure 9. Roll size drawing format 12 3 4 56789101112 13 14 12 3 4 56789101112 13 14 ACBDA C B D FRAME 3 h FRAME 2 FRAME 1 Frame connection lineL2L2/2 L1L1/240 20L1 L1/220 200 200 20 h/240 12 3 4 56789101112 13 14 12 3 4 56789101112 13 14 DFEGD F E G A B C BCA h h/4FRAME 1 FRAME 2FRAME 3 FRAME 4 FRAME 5FRAME 6