GME GMI L R-10E-1-2008 Static and Dynamic Testing Spare Wheel Tool Compartment Cover (English German This standard may be applied only for current projects incl Global Epsilon e (3 and.pdf
《GME GMI L R-10E-1-2008 Static and Dynamic Testing Spare Wheel Tool Compartment Cover (English German This standard may be applied only for current projects incl Global Epsilon e (3 and.pdf》由会员分享,可在线阅读,更多相关《GME GMI L R-10E-1-2008 Static and Dynamic Testing Spare Wheel Tool Compartment Cover (English German This standard may be applied only for current projects incl Global Epsilon e (3 and.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、LPSP GMI TP 1 03/98INTERNATIONALENGINEERINGSTANDARDSTest Procedure GMI L/R-10E-1Static and Dynamic TestingSpare Wheel / Tool Compartment CoverStatische und dynamische PrfungAbdeckung Ersatzrad / WerzeugfachApril 2008 Page 1 of 10Note: This standard may be applied only for current projects incl. Glob
2、al Epsilon (37#). It isSuperceded for all future projects and replaced by GMW14278.Hinweis: Diese Spezifikation darf nur noch fr laufende Projekte einschlielich Global Epsilon (37#) angewendet werden und ist fr alle zuknftigen Projekte ungltig und ersetzt durchGMW14278.GM INTERNATIONAL ENGINEERING S
3、TANDARD GMI L/R-10E-1April 2008 Page 2 of 10LPSP GMI 2 11/95RevisionsDate Paragraphnew03.98 ITDC release04.08 Set to Superceded statusnderungenDatum Abschnittnew03.98 ITEZ-Freigabe04.08 Auf Superceded Status umgestelltGM INTERNATIONAL ENGINEERING STANDARD GMI L/R-10E-1April 2008 Page 3 of 10LPSP GMI
4、 2 11/951 Introduction 1 Einleitung1.1 Purpose 1.1 ZweckThe purpose of this test procedure is thedetermination of the degree of depression of thespare wheel / tool compartment cover caused by astatic or dynamic force.Dieses Prfverfahren dient zur Ermittlung bzw.Bestimmung der Absenkung der Abdeckung
5、Ersatzrad / Werkzeugfach, die durch eine statischeund/oder dynamische Kraft hervorgerufen wird.1.2 Foreword 1.2 VorwortDue to the occurrence of vertical forces on thespare wheel / tool compartment cover and theassociated set, it is useful to perform tests on thecover and to determine limiting values
6、. Thus, therequired features such as: fitting, function, positionand fastening can be ensured.Bedingt durch das Auftreten von vertikalen Krftenauf die Abdeckung Ersatzrad / Werkzeugfach unddie damit verbundene Verformung, ist es sinnvolldie Abdeckung zu untersuchen und Grenzwertefestzulegen. Damit k
7、nnen geforderteLeistungsmerkmale wie z.B. Passung, Funktion,Position, und Befestigung gewhrleistet werden.1.3 Applicability 1.3 AnwendbarkeitThis specification applies to covers which areconstructed from e.g.: sheet metal and cover plate (e.g. TM 224000)Material thickness and shape according to draw
8、ingspecificationsDiese Vorschrift gilt fr Abdeckungen die imZusammenbau z.B. aus: Blech, und Abdeckplatte (z.B. TM 224000)bestehen.Materialdicke und Form nach Zeichnungsvorgabe1.4 DefinitionsN.a.1.4 DefinitionenN.a.1.5 References 1.5 Referenzen1.5.1 Order of PrecedenceIn the event of a conflict betw
9、een the text of thetest procedure and the documents cited herein, thetext of the test procedure takes precedence.Nothing in the test procedure, however, supersedesapplicable laws and regulations unless a specificexemption has been obtained.Remark: In the event of a conflict between theEnglish and th
10、e domestic language, the Englishlanguage shall take precedence.1.5.1 Rangfolge der DokumenteIm Falle eines Widerspruchs vom Text diesesPrfverfahrens und den Dokumenten, die in demPrfverfahren enthalten sind, hat der Text desPrfverfahrens Vorrang. Falls keine Ausnahmenvereinbart wurden, darf das Prfv
11、erfahren keineanzuwendenden Gesetze und Regelungen auerKraft setzen.Hinweis: Im Falle von Unstimmigkeiten zwischendem englischen und dem landessprachlichen Text,ist der englische Text ausschlaggebend.1.5.2 Government Documents 1.5.2 Staatliche DokumenteN. a. N. a.GM INTERNATIONAL ENGINEERING STANDAR
12、D GMI L/R-10E-1April 2008 Page 4 of 10LPSP GMI 2 11/951.5.3 General Motors Documents 1.5.3 General Motors Dokumente1.5.3.1 GMIO 1.5.3.1 GMIOTM 224000Cover plateTM 224000Abdeckplatte1.5.3.2 NAO 1.5.3.2 NAON. a. N. a.1.5.4 Industry Documents 1.5.4 Industrie DokumenteN. a. N. a.1.5.5 Supplier Documents
13、 1.5.5 Lieferanten DokumenteN. a. N. a.1.5.6 Other Documents 1.5.6 Andere DokumenteN. a. N. a.2 Resources 2 Gerte und Einrichtungen2.1 Facilities 2.1 Einrichtung2.1.1 2.1.1The set under dynamic stimulation shall bedetermined on a short-wave, large-block wavetrack.Die Verformung unter dynamischer Anr
14、egung istauf einer kurzwelligen Groblockwellenbahn zuermitteln.2.1.2 2.1.2Road section with 100 mm high kerbstone. Straenabschnitt mit Bordstein 100 mm hoch.2.2 Equipment 2.2 Ausrstung2.2.1 2.2.1Adjustable measuring rod Verstellbares Megestnge2.2.2 2.2.2Base plate / load surface with a surface area
15、of(300 x 300) mmGrundplatte / Belastungsflche mit einer Flchevon (300 x 300) mm2.2.3 2.2.3Base plate / load surface with a diameter of 180mmGrundplatte / Belastungsflche mit einemDurchmesser von 180 mm2.2.4 2.2.4Base plate with a diameter of 180 mm Grundplatte mit einem Durchmesser von 180 mm2.2.5 2
16、.2.5Steel tape measure StahlbandmaGM INTERNATIONAL ENGINEERING STANDARD GMI L/R-10E-1April 2008 Page 5 of 10LPSP GMI 2 11/952.2.6 2.2.6Fastening cables / tensioning belts Befestigungsseile / Spanngurte2.2.7 Weight 2.2.7 Gewichte2.2.7.1 2.2.7.1Static test with 100 kg test load; Stat. Versuch mit 100
17、kg Prflast;2.2.7.2 2.2.7.2Dynamic test with 60 kg test load; Dyn. Versuch mit 60 kg Prflast;2.2.7.3 2.2.7.3Misuse test : 50 kg sandbagOutside dimensions (50 x 35) cm - with two handle-loops on each short side.Misuse Test : Sandsack 50 kgAuenmae (50 x 35) cm - mit je zwei Griff-schlaufen an den Schma
18、lseiten.2.3 Test Vehicle/Test Piece 2.3 Versuchsfahrzeug/Probekrper2.3.1 2.3.1Spare wheel / tool compartment coverThe tool compartment or spare wheel well shall beequipped completely as per release.Ersatzrad / WerkzeugfachabdeckungDas Werkzeugfach bzw. die Ersatzradmulde wirdkomplett nach Freigabe a
19、usgestattet.2.3.2 Load surface for static / dynamicMeasurements and Kerbstone2.3.2 Belastungsflche bei statischer /dynamischer Messung und Bordstein2.3.2.1 2.3.2.1Load surface (300 x 300) mm with load spacing 450 mmBelastungsflche (300 x 300) mm bei Auflageab-stand 450 mm2.3.2.1 2.3.2.1Load surface
20、180 mm diameter with load spacing 450 mmBelastungsflche Durchmesser 180 mm beiAuflageabstand 450 mm3 Procedure 3 Durchfhrung3.1 Preparation 3.1 Vorbereitung3.1.1 3.1.1For the test, the lining of the cover shall beremoved, on the condition that this is not installedas a composite system. The test pie
21、ce shall beloaded vertically, at the centre or at its weakestpoint weight, described under 2.2.7. For thedynamic test, the weight shall be fixed in positionon the test piece by means of tensioning belts /fastening cables. The tool compartment or sparewheel well shall be fully equipped, as per releas
22、e.Fr den Versuch wird der Belag von der Abdeckungentfernt, falls diese nicht als Verbundsystemeingebaut ist. Der Probekrper wird mittig bzw. anseiner schwchsten Stelle vertikal mit dem unter2.2.7 beschriebenen Gewicht belastet. Bei derdynamischen Prfung wird das Gewicht mittelsSpanngurten / Befestig
23、ungsseilen auf demProbekrper fix positioniert. das Werkzeugfachbzw. die Ersatzradmulde wird komplett nachFreigabe ausgestattet.GM INTERNATIONAL ENGINEERING STANDARD GMI L/R-10E-1April 2008 Page 6 of 10LPSP GMI 2 11/951327546Fig. 1: Test setup Abb. 1: Prfaufbau1. Adjustable measuring rod2. Steel tape
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMEGMILR10E12008STATICANDDYNAMICTESTINGSPAREWHEELTOOLCOMPARTMENTCOVERENGLISHGERMANTHISSTANDARDMAYBEAPPLIEDONLYFORCURRENTPROJECTSINCLGLOBALEPSILONE3ANDPDF
链接地址:http://www.mydoc123.com/p-755439.html