GME 06011-2013 Cold Start Test for Toothed Belts of All Lengths (Revision 3 English German This standard may be applied only for current programs It is inactive for all future proj.pdf
《GME 06011-2013 Cold Start Test for Toothed Belts of All Lengths (Revision 3 English German This standard may be applied only for current programs It is inactive for all future proj.pdf》由会员分享,可在线阅读,更多相关《GME 06011-2013 Cold Start Test for Toothed Belts of All Lengths (Revision 3 English German This standard may be applied only for current programs It is inactive for all future proj.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、GeneralSpecification GME 06011LIMITED USECold Start Test for Toothed Belts ofAll LengthsKaltstarttest fr Zahnriemen allerLngenNOTE: This standard may be applied only forcurrent programs. It is inactive for all futureprojects and without replacement.HINWEIS: Diese Spezifikation darf nur noch frlaufen
2、de Projekte angewendet werden und ist fralle zuknftigen Projekte ohne Ersatz ungltig.1 Introduction 1 Einfhrung1.1 Scope. All toothed belts for engine timing. 1.1 Anwendungsbereich. Alle Zahnriemen derMotor-Steuerung.1.2 Mission / Theme. The aim of this GME is todetermine and to test the resistance
3、to coldof toothedbelts for engine timing at low temperatures.1.2 Aufgabe / Thema. Diese GME dient der Fest-legung und Erprobung der Kltebestndigkeit vonZahnriemen des Motor-Steuertriebes bei tiefen Tem-peraturen.1.3 Classification. Not applicable. 1.3 Einteilung. Nicht anwendbar.Note: Nothing in the
4、 specification, however, super-sedes applicable laws and regulations unless a spe-cific exemption has been obtained.Hinweis: Die Vorschrift darf keine anzuwendendenGesetze und Regelungen auer Kraft setzen.Note: In the event of a conflict between the Germanand theEnglish language,the German languages
5、halltake precedence.Hinweis: Im Falle von Unstimmigkeiten zwischendem deutschen und dem englischen Text ist derdeutsche Text ausschlaggebend.2 References 2 ReferenzenNote: Only the latest approved standards are appli-cable unless otherwise specified.Hinweis: Wenn nicht anders angegeben, ist jeweilsd
6、ie neueste Fassung der angegebenenReferenz gl-tig.2.1 External Standards/Specifications. 2.1 Externe Normen/Vorschriften.ISO 90102.2 GM Standards/Specifications. 2.2 GM Normen/Vorschriften.GME 604692.3 Additional References. Drawing no.24 422 961 and 90 530 285.2.3 Zustzliche Referenzen. Zeichnung N
7、r.24 422 961 und 90 530 285. Copyright 2013 General Motors Company All Rights ReservedPublication Department: GME Specification CenterFebruary 2013 Page 1 of 9PRD045 - VPRE ST 1 10/03 GME 06011 GM EUROPE ENGINEERING STANDARDS3 Test Preparation and Evaluation 3 Prfungsvorbereitung undAuswertung3.1 Re
8、sources. 3.1 Gerte und Einrichtungen.3.1.1 Calibration. The test facilities and equipmentshall be in good working order and shall have a validcalibration label.3.1.1 Kalibrierung. AllePrfeinrichtungen und -aus-rstungen mssen funktionsfhig sein und eine gl-tige Kalibrierplakette haben.3.1.2 Alternati
9、ves. Alternative test facilities andequipment may also be used. However, all measur-ing variables as specified in this specification shallbe determined correctly with respect to its physicaldefinition.3.1.2 Alternativen. EsknnenauchalternativePrf-einrichtungen und -ausrstungen verwendet werden.Alle
10、Messvariablen, wie sie in dieser Vorschrift ange-geben werden, mssen jedoch in Bezug auf ihre phy-sikalische Definition korrekt festgelegt werden.3.1.3 Facilities. See appropriate test procedure. 3.1.3 Einrichtungen. Siehe entsprechendes Prf-verfahren.3.1.4 Equipment. See appropriate test procedure.
11、 3.1.4 Ausrstung. Siehe entsprechendes Prfver-fahren.3.2 Test Samples. At least 5 new toothed belts shallbe tested.3.2 Prfteile. Es sind mindestens 5 neuwertigeZahnriemen zu prfen.3.3 Conditioning. See appropriate test procedure. 3.3 Probenvorbehandlung. Siehe entsprechendesPrfverfahren.3.4 Document
12、ation. Samples of componentsor material released to this specification shall betested for conformity with the requirements of thisspecification and approved by the responsible GMDepartment prior to the start of delivery of productionlevel components or materials.3.4 Dokumentation. Freigabemuster fr
13、die dieseVorschrift zutrifft, mssen nach dieser Vorschriftgeprft werden und von der verantwortlichen GMAbteilung genehmigt sein, ehe eine Lieferung erfol-gen kann.Anychange to thecomponentor materiale.g. design,function, properties, manufacturing process and/orlocation of manufacture requires a new
14、releaseof the product. It is the sole responsibility of thesupplier to provide the customer, unsolicited, withdocumentation of any change or modification to theproduct/process, and to apply for a new release.nderungen von z.B. Aufbau, Funktion, Eigen-schaften, Herstellungsprozess und Ort macheneine
15、Neufreigabe notwendig. Der Hersteller istverpflichtet, unaufgefordert den Abnehmer mit einerDokumentation ber alle Abstimmungen, Modifikatio-nen von Teilen und / oder Prozessen zu informierenund eine Neufreigabe zu beantragen.If not otherwise agreed to the entire verification testshall be repeated a
16、nd documented by the supplierprior to start of delivery of the modified or changedproduct. In some cases a shorter test can be agreedto between the responsible GM Department and thesupplier.Wenn nicht anders vereinbart, ist die komplette Frei-gabeprfung durch den Lieferanten zu wiederholenund das Er
17、gebnis zu dokumentieren, bevor die nde-rungen in der Lieferung einsetzen knnen. In Einzel-fllen kann zwischen der verantwortlichen GM Abtei-lung und Lieferant eine verkrzte Prfung vereinbartwerden.3.4.1 Test Results. 3.4.1 Prfergebnisse.3.4.1.1 Test Evaluation. The change in axle dis-tance L for len
18、gth measurements shall be testedand documented to GME 60469.3.4.1.1 Versuchsauswertung. Die Achsabstands-nderung L bei der Lngenmessung ist entspre-chend GME 60469 zu prfen und zu dokumentieren.The toothed belt has passed the test if after the test Der Zahnriemen hat die Prfung erfllt, wenn nachder
19、Prfung Copyright 2013 General Motors Company All Rights ReservedPage 2 of 9 February 2013PRD045 - VPRE ST G 10/03GM EUROPE ENGINEERING STANDARDS GME 06011a there are no cracks in the toothed belt and there isno separation of elastomer parts,a am Zahnriemen keinerlei Einrisse sowie keinerleiElastomer
20、teile ausgebrochen sind,b the number of test cycles prior to failure is t thenominal number of test cycles,b die Testzyklenanzahl bis zum Ausfall t der Soll-Testzyklenanzahl ist,c the residual tearing force of the whole toothed beltaccording to GME 60471 is t 70 % of that of a newbelt.c die Restreik
21、raft des gesamten Zahnriemensentsprechend GME 60471 t 70 % des Neuteilesbetrgt.3.4.1.2 Definition of Failure. The following aredefined as failures of the toothed belt:3.4.1.2 Ausfalldefinition. Als Ausfall des Zahnrie-mens wird definierta teeth, the cover fibre or toothed belt backing havebecome cra
22、cked or separated,a jeder Einriss oder Ausbruch in den Zhnenoder imDeckgewebe sowie am Zahnriemenrcken,b the number of test cyclesprior tofailure isless thanthe nominal number of test cycles,b die Testzyklenzahl bis Ausfall kleiner als der Soll-Testzyklenzahl ist,c the residual tearing force of the
23、whole toothed beltis 70 % of that of a new belt.c die Restreikraft des gesamten Zahnriemens 70 % vom Neuteil betrgt.3.4.1.3 Table of Values for Toothed Belt. Valid forHot Box and cooling chamber.3.4.1.3 Wertetabelle fr Zahnriemen. Gltigfr HotBox und Kltekammer.Load controlled /Beanspruchung geregelt
24、FinNHot box test torque /Moment Hot-Box-Testin NmWidth of toothed belt /Zahnriemenbreitein mmComment /Bemerkungto be added /wird noch zugefgt 15 17 Fam I OHC 1.4 l / 1.6 l800 21 20 FamIIOHC,FamIDOHC1000 25 24 Fam II 16 V1400 40 30 V6/2.5l/3.0l/2.6l/3.2l3.4.2 Deviations from Test Procedure. Deviation
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 1人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GME060112013COLDSTARTTESTFORTOOTHEDBELTSOFALLLENGTHSREVISION3ENGLISHGERMANTHISSTANDARDMAYBEAPPLIEDONLYFORCURRENTPROGRAMSITISINACTIVEFORALLFUTUREPROJPDF

链接地址:http://www.mydoc123.com/p-754830.html