FORD WSS-M99C130-A-2016 DIESEL EXHAUST FLUID (DEF) TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M99C130-A-2016 DIESEL EXHAUST FLUID (DEF) TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M99C130-A-2016 DIESEL EXHAUST FLUID (DEF) TO BE USED WITH FORD WSS-M99P1111-A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 2 2016 07 05 Revised See Summary of Revisions C. Richardson, NA 2011 03 17 Revised Revised: Title and section 3.4 C. Richardson, NA 2008 09 12 Activated C. Richardson Controlled document at www.MATS.com Copyright 2016 Ford Global Technol

2、ogies, LLC Page 1 of 3 DIESEL EXHAUST FLUID (DEF) WSS-M99C130-A 1. SCOPE The material defined by this specification is a NOx-reduction agent for use in vehicles equipped with Selective Catalytic Reduction (SCR) systems. 2. APPLICATION This specification was released originally for material used as i

3、nitial fill and service fluid for diesel vehicles equipped with selective catalyst reduction converters. 3. REQUIREMENTS This material must meet the requirements of CEFIC (European Chemical Industry Council) according to DIN 70070 and ISO 22241-1. 3.1 APPROVED SOURCES This specification requires the

4、 use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer.

5、3.2 UREA CONTENT 31.8 33.2 % (m/m) (ISO 22241-2 Annex B (*) ISO 22241-2 Annex C) (*) Calculated without subtracting nitrogen from ammonia 3.3 DENSITY at 20 C 1.087 1.093 g/cm3 (ISO 3675 or ISO 12185) 3.4 REFRACTIVE INDEX at 20 C 1.3814 - 1.3843 (ISO 222412 Annex C) 3.5 ALKALINITY AS NH3 0.2 % (m/m),

6、 max (ISO 222412 Annex D) 3.6 BIURET 0.3 % (m/m) max (ISO 222412 Annex E) ENGINEERING MATERIAL SPECIFICATION WSS-M99C130-A Copyright 2016, Ford Global Technologies, LLC Page 2 of 3 3.7 ALDEHYDES 5 mg/kg max (ISO 222412 Annex F) 3.8 INSOLUBLE MATTER 20 mg/kg max (ISO 222412 Annex G) 3.9 PHOSPHATE (PO

7、4) 0.5 mg/kg max (ISO 222412 Annex H) 3.10 CALCIUM 0.5 mg/kg max (ISO 222412 Annex I) 3.11 IRON 0.5 mg/kg max (ISO 222412 Annex I) 3.12 COPPER 0.2 mg/kg max (ISO 222412 Annex I) 3.13 ZINC 0.2 mg/kg max (ISO 222412 Annex I) 3.14 CHROMIUM 0.2 mg/kg max (ISO 222412 Annex I) 3.15 NICKEL 0.2 mg/kg max (I

8、SO 222412 Annex I) 3.16 ALUMINUM 0.5 mg/kg max (ISO 222412 Annex I) 3.17 MAGNESIUM 0.5 mg/kg max (ISO 222412 Annex I) 3.18 SODIUM 0.5 mg/kg max (ISO 222412 Annex I) 3.19 POTASSIUM 0.5 mg/kg max (ISO 222412 Annex I) 4. GENERAL INFORMATION The information given below is provided for clarification and

9、assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, a

10、nd Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be avai

11、lable for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. ENGINEERING MATERIAL SPECIFICATION WSS-M99C130-A Copyright 20

12、16, Ford Global Technologies, LLC Page 3 of 3 4.2 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect t

13、he materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SR

14、EA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.3 RESTRICTED SUBSTANCE MANAGEMENT STANDARD

15、 Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this sta

16、ndard on a continuing basis through IMDS and or GMAP reporting. 4.4 Quality Control records must be made available to Fuels and Lubricants and Materials Engineering upon request. 5. SUMMARY OF REVISIONS 2016 07 05 added DEF to the title. Removed WSS-M99P1111-A and added those requirements directly into this specification. Revised units on density from kg/m3 to g/cm3 2011 03 17 Revise title and Reactive Index