FORD WSS-M3H133-C1-2016 CARPET BCF NYLON 6 CUT PILE BAVARIA PATTERN 542 g m2 (16 oz) NOMINAL POLYETHYLENE AND MASS BACKED TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD WSS-M3H133-C1-2016 CARPET BCF NYLON 6 CUT PILE BAVARIA PATTERN 542 g m2 (16 oz) NOMINAL POLYETHYLENE AND MASS BACKED TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M3H133-C1-2016 CARPET BCF NYLON 6 CUT PILE BAVARIA PATTERN 542 g m2 (16 oz) NOMINAL POLYETHYLENE AND MASS BACKED TO BE USED WITH FORD WSS-M99P1111-A .pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 00 2016 02 04 Released L. Sinclair, NA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 1 of 5 CARPET, BCF NYLON 6, CUT PILE, WSS-M3H133-C1 BAVARIA PATTERN, 542 g/m2 (16 oz) NOMINAL POLYETHYLENE AND MASS
2、 BACKED 1. SCOPE The materials defined by this specification are fine denier, bulked continuous filament (BCF) nylon, cut pile carpets, tufted into a synthetic primary foundation. 2. APPLICATION This material was originally released for Lincoln full floor molded carpets. 3. REQUIREMENTS 3.1 APPROVED
3、 SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available extern
4、ally through a Ford Materials Engineer. 3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning e
5、nvironment or soon after removal. 3.3 PERFORMANCE CRITERIA 3.3.1 In addition to the requirements listed herein, the end-item floor carpet shall be tested to WSS-M8P16-B and any additional SDS requirements. The details for each of the suppliers specific construction shall be documented in the supplem
6、ent attached and uploaded into the scanned data package. 3.3.2 Vehicle Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/ latest. Data must be included at the appropriate program mi
7、lestone 3.4 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from finished roll goods prior to any subsequent operations, such as reheating or molding. 3.5 APPEARANCE The color, pattern, and gloss shall match the approved Corporate Design master sample. 3.6 METHOD OF DYING
8、 Solution Dyed ENGINEERING MATERIAL SPECIFICATION WSS-M3H133-C1 Copyright 2016, Ford Global Technologies, LLC Page 2 of 5 3.7 COMPOSITION 3.7.1 Pile Yarn Nylon 6 (ASTM D 276) 3.7.2 Primary Foundation Polyester (ASTM D 276) 3.7.3 Back Coating Polyethylene (ASTM D 276) 3.7.4 Secondary Foundation Mass
9、Backing (ASTM D 276) * Materials approved for each suppliers construction can be found on the supplement form in the construction package. 3.8 CONSTRUCTION 3.8.1 Pile Yarn 1000 Denier (ASTM D 1244) 3.8.2 Pile Count (ISO 1763) Rows / 100 mm 50.4 Stitches / 100 mm 51.0 Rows and stitches per 100 mm sha
10、ll be based on an average count on a 254 mm length of carpet and shall not exceed the tolerance provided on the approved construction supplement for the approved material. 3.8.3 Needle Gauge 1.98 mm 3.9 THICKNESS 3.9.1 Pile Height 5.6 mm Nominal (ISO 1765) Pile Height tolerances approved for each su
11、ppliers construction can be found in the construction package 3.9.2 Primary Foundation 0.5 mm Nominal (ISO 1765) 3.9.3 Back Coating (mm) Report * (ISO 1765) The back coating shall thoroughly saturate the base of the pile fiber bundles to ensure adequate tuft lock. Penetration of the back coating thr
12、ough to the face shall be controlled to provide the required resistance to abrasion and fiber loss, but it shall not be visible on the face of the pile fiber. 3.9.4 Secondary Foundation (mm) Report * (ISO 1765) *Thicknesses and tolerances approved for each suppliers construction can be found on the
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM3H133C12016CARPETBCFNYLON6CUTPILEBAVARIAPATTERN542GM216OZNOMINALPOLYETHYLENEANDMASSBACKEDTOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-753307.html