FORD WSS-M3H117-A2-2009 CARPET POLYPROPYLENE NON-BACKCOATED TO BE USED WITH FORD WSS-M99P1111-A 《无背涂的聚丙烯（PP）地毯 与标准FORD WSS-M99P1111-A一起使用 ［使用 FORD WSS-M3H120-A2］》.pdf

《FORD WSS-M3H117-A2-2009 CARPET POLYPROPYLENE NON-BACKCOATED TO BE USED WITH FORD WSS-M99P1111-A 《无背涂的聚丙烯（PP）地毯 与标准FORD WSS-M99P1111-A一起使用 ［使用 FORD WSS-M3H120-A2］》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M3H117-A2-2009 CARPET POLYPROPYLENE NON-BACKCOATED TO BE USED WITH FORD WSS-M99P1111-A 《无背涂的聚丙烯（PP）地毯 与标准FORD WSS-M99P1111-A一起使用 ［使用 FORD WSS-M3H120-A2］》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2009 10 20 N-STATUS Replaced by WSS-M3H120-A2 L. Sinclair, NA 2000 09 21 Revised Updated A. Cockman 1996 12 12 Activated Y. Alaniva L. Graham Printed copies are uncontrolled Page 1 of 3 Copyright 2009, Ford

2、Global Technologies, Inc. CARPET, POLYPROPYLENE, NON-BACKCOATED WSS-M3H117-A2 NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is needled flat felt, nonwoven unbacked carpet of good quality and uniform composition. 2. APPLICATION This specification was originally rel

3、eased for material used as a covering fabric for package trays only. This material must always be bonded 100 % to a substrate material to lock in the surface fibers and meet all the requirements specified herein. 3. REQUIREMENTS Material specification requirements are to be used for initial qualific

4、ation of materials. In addition to the requirements listed herein, the end-item carpet or trim assembly (molded or otherwise fabricated, shall meet all applicable requirements of WSS-M15P6-D and other requirements specified on the engineering drawing. 3.1 QUALITY SYSTEM REQUIREMENTS Material supplie

5、rs and part producers must conform to the Companys Quality System Requirements. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS IR spectra and thermograms established for initial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory.

6、All samples shall produce IR spectra and thermograms that correspond to the reference standard when tested under the same conditions. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relati

7、ve humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. ENGINEERING MATERIAL SPECIFICATION WSS-M3H117-A2 Page 2 of 3 Copyright 2009, Ford Global Technologies, Inc. 3.4 COMPOSITION (ASTM D 276) Fiber: 100 % polypropylene, UV resistant 3.5 M

8、ETHOD OF DYEING: Solution dyed or equivalent 3.6 CONSTRUCTION 3.6.1 Fiber Size and Description 11.1 dtex (ASTM D 1244) (polypropylene) 3.6.2 Thickness, range 3.0 +/- 0.5 mm (ASTM D 418) 3.7 WEIGHT, min* (FLTM BN 106-01) Pile Fiber: 270 g/m2 Total: 270 g/m2 *or as specified on Engineering Drawing. 3.

9、8 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute* tested as a composite *This material must always be bonded 100 % to another material to form a composite, and the composite must not burn in excess of 100 mm/minute. 3.9 ELONGATION at 111 N, range (ASTM D 5034, Grab Method, 305 mm/minu

10、te jaw speed) WMD 60 +/- 15 %AMD 30 +/- 10 % ENGINEERING MATERIAL SPECIFICATION WSS-M3H117-A2 Page 3 of 3 Copyright 2009, Ford Global Technologies, Inc. 3.10 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which app

11、roval was originally granted. Prior to making any changes to the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the affected Purchasing, and Materials Engineering activi

12、ties (with reasons) of the proposed changes. Upon notification of the Company, further instructions will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested. Substance restrictions imposed by regulations or Com

13、pany direction applies to the materials addressed by this document. The restrictions are identified in Restricted Substance Management Standard WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification for direct supply to the Company must have prior approval. Certain materia

14、ls subcontracted by part suppliers may also require prior approval. These include materials critical to the Companys business for regulatory, safety, environmental or compatibility requirements or contractual agreements. Suppliers desiring approval of their materials shall first obtain an expression

15、 of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification.