FORD WSS-M3H105-A8-2008 CARPET POLYESTER FLAT NEEDLED LATEX PRECOAT POLYETHYLENE BACKCOATED - TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯背涂的带乳胶预涂层的扁平针刺聚酯地毯 与标准FORD WSS-M99P1111-A一起.pdf
《FORD WSS-M3H105-A8-2008 CARPET POLYESTER FLAT NEEDLED LATEX PRECOAT POLYETHYLENE BACKCOATED - TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯背涂的带乳胶预涂层的扁平针刺聚酯地毯 与标准FORD WSS-M99P1111-A一起.pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M3H105-A8-2008 CARPET POLYESTER FLAT NEEDLED LATEX PRECOAT POLYETHYLENE BACKCOATED - TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯背涂的带乳胶预涂层的扁平针刺聚酯地毯 与标准FORD WSS-M99P1111-A一起.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes Rev. 2 2008 11 03 N-STATUS Replaced by WSS-M15P32-C L. Sinclair, FNA 1999 02 02 Activated L. Daniv-Zarewych WP 3948-a Page 1 of 4 CARPET, POLYESTER, FLAT NEEDLED, WSS-M3H105-A8 LATEX PRECOAT, POLYETHYLENE BACK
2、COATED NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by this specification are flat needled, polyester, non-woven carpets of good quality and uniform composition. 2. APPLICATION This specification was originally released for materials used for trunk covering material for the 1999 1/2
3、Ford Focus. 3. REQUIREMENTS In addition to the requirements listed herein, the end-item carpet assembly (molded or otherwise fabricated), shall meet all requirements of the WSS-M15P32-C performance specification. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to Q
4、uality System Requirements, QS-9000. Material specification requirements are to be used for initial qualification of materials. A Control Plan for ongoing production verification is required. This plan must be reviewed and approved by the relevant Ford Materials activity and/or Ford Supplier Technic
5、al Assistance (STA) prior to production parts submission. Appropriate statistical tools must be used to analyze process/product data and assure consistent processing of the materials. Part producers using this material in their products, must use Ford approved materials and must conform to a process
6、 control plan which has been approved by STA and/or the relevant Materials Activity. ENGINEERING MATERIAL SPECIFICATION WSS-M3H105-A8 WP 3948-b Page 2 of 4 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS Ford Motor Company, at its option, may conduct infrared and/or thermal analysis of materi
7、al/parts supplied to this specification. The IR spectra and thermograms established for initial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce IR spectra and thermograms that correspond to the reference stan
8、dard when tested under the same conditions. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions u
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM3H105A82008CARPETPOLYESTERFLATNEEDLEDLATEXPRECOATPOLYETHYLENEBACKCOATEDTOBEUSEDWITHFORDWSSM99P1111A

链接地址:http://www.mydoc123.com/p-753268.html