FORD WSS-M2D505-A7-2013 THERMOPLASTIC ELASTOMER STYRENE POLYOLEFIN BLOCK COPOLYMER (TES) 49 DUROMETER A HARDNESS EXTERIOR WEATHERABLE TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD WSS-M2D505-A7-2013 THERMOPLASTIC ELASTOMER STYRENE POLYOLEFIN BLOCK COPOLYMER (TES) 49 DUROMETER A HARDNESS EXTERIOR WEATHERABLE TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M2D505-A7-2013 THERMOPLASTIC ELASTOMER STYRENE POLYOLEFIN BLOCK COPOLYMER (TES) 49 DUROMETER A HARDNESS EXTERIOR WEATHERABLE TO BE USED WITH FORD WSS-M99P1111-A .pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Rev. 01 2013 08 02 Revised Changed Brittleness Point from -53C to -52C H. Santos, FSAO 2009 02 04 Activated K. Mueller, FNA Controlled document at www.MATS Copyright 2013, Ford Global Technologies, Inc. Page 1 of 4 THERMOPLASTIC ELASTOMER, STY
2、RENE POLYOLEFIN WSS-M2D505-A7 BLOCK COPOLYMER (TES), 49 DUROMETER A HARDNESS, EXTERIOR WEATHERABLE 1. SCOPE The material defined by this specification is a black U.V. stabilized thermoplastic styrene-ethylene/butylene-styrene copolymer elastomer. The material possesses a good exterior weathering cap
3、ability and can be processed by conventional thermoplastic molding techniques such as injection and/or extrusion molding. 2. APPLICATION This specification was released originally for material used for cowl top ventilator grille seals and muckets. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUC
4、TION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 MATERIAL TESTING 3.2.1 Preparation of Test Specimens Whenever possible, all test specimens shall be die-cut from the finished parts. When not feasibl
5、e, specimens cut from molded test sheets manufactured from the same material and with equivalent cure to the molded parts are recommended. The test sheets shall have the following dimensions: 150 x 150 mm, min x 2.0 +/- 02 mm ENGINEERING MATERIAL SPECIFICATIONWSS-M2D505-A7Copyright 2013, Ford Global
6、 Technologies, Inc. Page 2 of 4 3.3 ORIGINAL PROPERTIES 3.3.1 Density, +/- 0.03 g/cm31.18 (ISO 1183, Method A) 3.3.2 Hardness, Durometer A, points 43 53 (ISO 868, 10 second dwell, 6.0 mm plied-up specimen) 3.3.3 Tensile Strength 3.5 MPa min (ISO 37, test speed: 508 mm/min) 3.3.3.1 Elongation at Brea
7、k, 535 % min (Test method according to para 3.3.3) 3.3.3.2 Modulus at 100% Elongation 1.4 MPa, min (Test method according to para 3.3.3) 3.3.4 Tear Strength (ISO 34, Method B Procedure A) 3.3.4.1 Parallel to Flow 17 kN/m min 3.3.4.2 Perpendicular to Flow 17 kN/m min 3.3.5 Brittleness Point -52 C max
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM2D505A72013THERMOPLASTICELASTOMERSTYRENEPOLYOLEFINBLOCKCOPOLYMERTES49DUROMETERAHARDNESSEXTERIORWEATHERABLETOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-752867.html