FORD WSS-M1H1272-A11-2016 FABRIC HUDSON EMBOSSED PATTERN FLAT WOVEN 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M1H1272-A11-2016 FABRIC HUDSON EMBOSSED PATTERN FLAT WOVEN 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1H1272-A11-2016 FABRIC HUDSON EMBOSSED PATTERN FLAT WOVEN 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2016 10 03 Released P. Zhang, APA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 1 of 3 FABRIC, HUDSON EMBOSSED PATTERN, FLAT WOVEN WSS-M1H1272-A11 100% VIRGIN WITH SOIL REPELLANT 1. SCOPE The materi

2、al defined by this specification is a HUDSON Embossed pattern on the Soft Twill base flat woven polyester face fabric made from 100% virgin yarn. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for Taurus 2015 Seat Insert for China Production. T

3、he fabric was approved tri-laminated with foam and backing scrim. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, o

4、r other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 APPEARANCE The color, pattern, and finish shall match the approved Corporate Design master sample. 3.3 FABRIC PERFORMANCE In addition to the requirements listed h

5、erein, the fabric shall meet all requirements of WSS-M8P18-B1/B2/B3/B4/latest as applicable. 3.4 VEHICLE INTERIOR ENVIRONMENTAL PERFORMANCE Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/latest, Performance, Vehicle Interior Environmental Quality Mater

6、ial/Component Requirements. Data must be included in material submission package. 3.5 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the m

7、aterial should occur in the conditioning environment or soon after removal. ENGINEERING MATERIAL SPECIFICATION WSS-M1H1272-A11 Copyright 2016, Ford Global Technologies, LLC Page 2 of 3 3.6 FABRIC CONSTRUCTION 3.6.1 Fabric Count +/- 5% tolerance (ASTM D3775) Warp 527 / 10 cm Fill 283 / 10 cm 3.6.2 Fa

8、bric Weight, +/- 5% tolerance 312 g/m2 (FLTM BN 106-01) 3.7 COMPOSITION (ASTM D 629) Fabric 100% Polyester 3.8 YARN CONSTRUCTION (ASTM D1244) Warp Weft Fabric 333 Dtex / F72, 333 Dtex/ F96 (Polyester, False Twist Texturized) (Polyester, False Twist Texturized) 3.9 FABRIC METHOD OF DYEING Piece Dyed

9、3.10 FABRIC FINISHING OPERATIONS Washing, drying, Pad SR + fixing + embossing 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1

10、Purchase departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. 4.2 If yarn is locally sourced it must meet the above fabric construction, composition and yarn construction. The fabric must also meet the re

11、quirements of WSS-M8P18-B1/B2/B3/B4/latest. 4.3 Global strategy for this fabric is to use tri-laminate/foam & scrim construction in all regions. 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product De

12、velopment, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples

13、must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All material

14、s must be equivalent in all characteristics to the material upon which approval was originally granted. ENGINEERING MATERIAL SPECIFICATION WSS-M1H1272-A11 Copyright 2016, Ford Global Technologies, LLC Page 3 of 3 Prior to making any changes to the material originally approved, whether or not such ch

15、anges affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineerin

16、g Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.6 RESTRICTED SUBSTANCE MANAG

17、EMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis. 5. SUMMARY OF REVISIONS