FORD WSS-M15P44-B-2014 PERFORMANCE THROW IN MAT ASSEMBLIES CARPETED TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M15P44-B-2014 PERFORMANCE THROW IN MAT ASSEMBLIES CARPETED TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M15P44-B-2014 PERFORMANCE THROW IN MAT ASSEMBLIES CARPETED TO BE USED WITH FORD WSS-M99P1111-A .pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 02 2014 04 02 Revised See Summary of Revisions L. Sinclair, NA 2013 01 11 revised See summary of revision for details L. Sinclair, FNA 2008 06 25 Activated L. Schmalz, FNA J. Williams, FOE Controlled document at www.MATS Copyright 2014, Fo

2、rd Global Technologies, LLC Page 1 of 8 PERFORMANCE, THROW IN MAT ASSEMBLIES, CARPETED WSS-M15P44-B 1. SCOPE This specification defines the standard requirements for a good quality, carpeted throw-in mat which consists of carpet and substrate material. 2. APPLICATION This specification was released

3、for tufted throw-in mats designed to protect floor coverings. 2.1 LIMITATION Nonwoven carpets are not applicable to this specification. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Prod

4、uction Materials (WSS-M99P1111-A). 3.1.1 In addition to the requirements listed herein, the end-item floor mat assembly (molded or otherwise fabricated), shall meet all requirements of the material specifications for the individual components, as well as SDS requirements. Edge binding used on floor

5、mats shall meet WSS-M8P24-A and serge thread used on floor mats shall meet WSS-M8P22-A. 3.1.2 Materials used in interior applications must meet the requirements outlined in WSSM99P2222-D1/Latest, Data must be included in material submission package. 3.2 SAMPLE SELECTION All evaluations shall be cond

6、ucted on test specimens taken from production representative throw-in mat assemblies. See Table 1 and Table 2 for testing requirements & sample size. Final determination of pass/fail criteria for the italicized items will be made by Ford Materials Engineering. 3.3 APPEARANCE (FLTM BI 109-01)The colo

7、r, pattern, and finish shall match the approved Design Center master sample, or shall be specified on the engineering drawing. 3.4 WEIGHT (FLTM BN 106-01) The fiber weight shall be specified in the Material Specification and total weight shall be as specified in the Supplement Form. ENGINEERING MATE

8、RIAL SPECIFICATION WSS-M15P44-B Copyright 2014, Ford Global Technologies, LLC Page 2 of 8 3.5 RESISTANCE TO MILDEW The material shall exhibit no visible evidence of mildew growth and/or objectionable odor after 7 days exposure in a humidity cabinet maintained at 98 +/- 2% relative humidity 38 +/- 2

9、C. 100mm x 100 mm sample size. 3.6 ODOR (FLTM BO 131-03, Variant C) Condition 1 (23 +/- 2 C) Rating 3 max. Condition 2 (40 +/- 2 C) Rating 3 max. Condition 3 (65 +/- 2 C) Rating 3 max. 3.7 PHOTOMETRIC FOGGING (SAE J1756, except paragraph 4.10 , 3 h at 100 C heating, 21 C cooling plate, post test con

10、ditioning 16 h) Fog Number 70 min Formation of clear film, droplets or crystals is cause for rejection. 3.8 PHYSICAL PROPERTIES 3.8.1 Water Shrinkage (FLTM BN 105-01/SAE J883) WMD & AMD 2.0% max 3.8.2 Heat Shrinkage (FLTM BN 105-01/SAE J883 Except instead of water, use 7 days at 80 +/- 2 C) WMD & AM

11、D 2.0% max 3.8.3 Dimensional Stability (FLTM BN 105-03, 2 cycles) WMD & AMD, expansion and contraction 2.0% max 3.8.4 Tensile Strength (ASTM D 5034) Dry and Wet (immersed) WMD & AMD 400 N min 3.8.5 Tensile after Aging 80% of Original min (FLTM BO 116-01 age face carpet 225.6 kJ/m2,ASTM D5034) 3.8.6

12、Trapezoidal Tear, (ASTM D 5587, Option 1 (Multiple Peak Force Average) Dry and Wet WMD and AMD 90 N min ENGINEERING MATERIAL SPECIFICATION WSS-M15P44-B Copyright 2014, Ford Global Technologies, LLC Page 3 of 8 3.8.7 Pile Tuft Pull Strength (ASTM D1335 original) Room Temperature 16 N min Tuft Pull af

13、ter 7 days at 80+/-2 C (pull at RT) 10 N min 3.8.8 Resistance to Heat Test Method: Place in an oven stacked, a raw carpet with no insulation(on bottom), floor mat assembly (on top), with a 2 kg load, maximum of area 5800 mm2, at 80 +/- 2 C for 6 hours. 100mm x 100 mm sample size. Raw carpet construc

14、tion tested will be program dependent. There shall be no adhesion of the floor mat assembly to the raw carpet, or flattening of the nibs (if applicable). 3.8.9 Adhesion of Carpet To Substrate (FLTM BN 113-01, Carpet to backing) WMD & AMD Original, Cycled, and Immersed 0.96 N/ mm min 3.8.10 Cold Resi

15、stance No cracking (SAE J323, Method A, 15mm or delamination mandrel carpet face down) Original AMD and WMD Aged 24 h at 80 +/- 2 C then 24 h at -30+/- 2 C AMD and WMD 3.8.11 Migration Staining Rating 5 min (FLTM BN103-01, ISO 105-A03 AATCC Evaluation Procedure 2) Expose to the floor mat backing to

16、the face of the applicable floor carpet material for 24 h The throw-in mat assembly shall exhibit no migration of backing material, or any other foreign matter, to the carpet surface of the floor system while in use. 3.8.12 Cold Temperature Curl Part must lay within 5(SH-0033/ RQT-010516/012924, 12x

17、12 inch section) mm of flat 25 mmfrom the edge of thesample within 25 Minutes. 3.8.13 Coefficient of Friction 2.0 min (SH-0089 / RQT-010516/012959) Tested against non woven and tufted floor carpets. Note for nibbed floor mats a typical nib and nib placement is to be used for construction approval. E

18、NGINEERING MATERIAL SPECIFICATION WSS-M15P44-B Copyright 2014, Ford Global Technologies, LLC Page 4 of 8 3.9 TABER ABRASION 4000 cycles (SAE J1530, 1000 g load, H-18 wheels) There shall be no primary backing visible after abrasion testing in excess of the failure criteria shown in Appendix 1. The ca

19、rpet shall exhibit no evidence of fraying, bearding or pilling caused by the pilling or separation of individual filaments or yarns. 3.10 APPEARANCE PROPERTIES 3.10.1 Resistance to Fade (FLTM BO 116-01, ISO 105-A02/ AATCC Evaluation Procedure 1) 225.6 kJ/m2 Rating 4 min. 3.10.2 Fiber Deterioration a

20、fter UV Exposure 3200 cycles (SAE J1530-A, 1000 g load,H-18 wheels) No deterioration of fibers or yarns after testing to the applicable exposure levels in section 3.10.1. See Appendix 1 for failure criteria. 3.10.3 Resistance to Crocking (FLTM BN 107-01, ISO 105-A03 AATCC Evaluation Procedure 2) Dry

21、 & Distilled Water Rating 4 min 3.10.4 Resistance to Bleeding Rating 4 min (FLTM AN 101-01, ISO 105-A03 AATCC Evaluation Procedure 2 3.10.5 Heat Ageing Rating 4 min (7 days at 80 +/- 2 C, ISO 105-A02/ AATCC Evaluation Procedure 1) No individual yarn or combination of yarns shall exhibit fiber deteri

22、oration or color tone change in excess of the above rating. There shall be no visual deterioration of backcoating. 100 mm x 100 mm sample size. 3.10.6 Soiling and Cleanability (FLTM BN 112-08, ISO 105-A03 AATCC Evaluation Procedure 2) After cleaning Rating 4 min 3.11 FLAMMABILITY (ISO 3795) Burn Rat

23、e 100mm/minute max ENGINEERING MATERIAL SPECIFICATION WSS-M15P44-B Copyright 2014, Ford Global Technologies, LLC Page 5 of 8 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions conce

24、rning Engineering Material Specifications. 5. SUMMARY OF REVISIONS 2014 04 02 Clarified pass / fail evaluation in section 3.2 sample selection. Added clarification for fog evaluation. Added clarification for odor testing. Added column for changing the backing weight only. The face fiber and weight a

25、long with the backing composition will not change. Added line to identify that clip testing is also required by the D&R before the material can be approved. Added column for new denier in table 1 Identified testing required for trunk mat applications. For cold resistance clarified that testing is ne

26、eded in both AMD and WMD directions. Added sample size 100 mm x 100 for mildew, heat aging and resistance to heat Added DV/PV table 2. 2013 01 11 - Updated format - Added VIEQ requirement - Removed SAE method for odor - Updated Trap Tear method - Removed note in section 3.8.9 adhesion to carpet subs

27、trate limiting requirement to extruded or molded samples. - Changed mandrel from 6 mm to 15 mm in 3.8.10 - Added Cold Curl and Coefficient of Friction - Changed taber from graduated requirements back to 1 requirement to reflect actual performance - Removed reference to edge treatments, being replace

28、d by WSS-M8P24-A - Deleted fiber loss requirement. - Changed fiber deterioration from a visual requirement (tape pull) to taber. - Removed instrumented option for resistance to crocking - Updated testing table. ENGINEERING MATERIAL SPECIFICATION WSS-M15P44-B Copyright 2014, Ford Global Technologies,

29、 LLC Page 6 of 8 TABLE 1: TESTING REQUIREMENTS New Construction (New Face Fiber and Backing)* New Backing Only * New Backing Weight or Manufacturing Site Only * New Face Fiber Weight Only * New Colors (MCDCC) New Denier * 3.3 Appearance 1 1 1 1 3.4 Weight 3 3 3 3 3 3.5 Resistance to Mildew 1 1 1 3.6

30、 Odor 1 1 1 3.7 Fogging (plates) 1 1 1 3.8.1 Water Shrinkage 1 1 1 1 3.8.2 Heat Shrinkage 1 1 1 1 3.8.3 Dimensional Stability 1 1 1 1 3.8.4 Tensile Strength WMD 3 3 3 3 AMD 3 3 3 3 3.8.5 Tensile after ageing WMD 3 3 3 3 AMD 3 3 3 3 3.8.6 Trapezoidal Tear WMD 3 3 3 3 AMD 3 3 3 3 3.8.7 Pile Tuft Pull

31、Strength Room Temp 3 3 3 3 3 Heated 3 3 3 3 3 3.8.8 Resistance to Heat 1 1 3.8.9 Adhesion of carpet to substrate 3 per condition 3 per condition 3 per condition 3 3.8.10 Cold Resistance 3 3 3 3.8.11 Migration Staining 1 1 3.8.12 SH-0033 Throw in Mat Cold Temperature Curl Test 3 per direction 3 per d

32、irection 3 per direction 3 per direction 3.8.13 SH-0089 Coefficient of Friction 5 per direction 5 per direction 5 per direction 3.9 Taber Abrasion 3 3 3 3 3 3.10.1 Resistance to Fade 1 1 1 3.10.2 Fiber Deterioration after UV 1 1 3.10.3 Resistance to Crocking 1 1 1 3.10.4 Resistance to Bleeding 1 3.1

33、0.5 Heat Ageing 1 1 1 3.10.6 Soiling and Cleanability 1 1 3.11 Flammability* 5 5 5 5 SH-0117 Clip Testing (Required for approval) X X X X X *New construction is defined as new fiber supplier or new denier and new backing type/weight. * Indicates that the face fiber and weight of fiber has been appro

34、ved to the given Material Specification. * Indicates that the backing and denier/supplier has been approved to the given Material Specification. Change in face fiber weight only. * Where flammability is required FMVSS 302 can be used instead of the ISO method. * Indicates that the construction is fu

35、lly approved but the backing will have a different weight or a new manufacturing site, on an already approved construction, is being requested. * Indicates that the construction is fully approved but the denier only has changed. Tested samples for italicized items must be submitted to Ford Materials

36、 Engineering. Note: The minimum number of specimens defined by the test method is noted in the table. Note: For trunk mats SH-0033, SH-0089 and SH-0117 testing is not required. ENGINEERING MATERIAL SPECIFICATION WSS-M15P44-B Copyright 2014, Ford Global Technologies, LLC Page 7 of 8 TABLE 2: DV/PV TE

37、STING REQUIREMENTS Component DV Testing Component PV Testing* 3.4 Weight 1 3.6 Odor 3 specimens per condition 3.7 Fogging (plates) 1 3.8.7 Tuft pull Room Temperature 3 Heated 3 3.8.9 Adhesion of Carpet to Substrate 3 per condition 3 per condition 3.8.13 Coefficient of Friction (SH-0089 / RQT-010516/

38、012959) 3 3.9 Taber Abrasion 3 3 3.11 Flammability Per Method Per Method Cold Curl (SH-0033/ RQT-010516/012924) 6 driver mats (3 per direction) 6 driver mats (3 per direction) SH-0117 Clip Testing (Required for approval) Required Ford PD to determine sample size Note: Fog plates, taber, and peel adh

39、esion must be reviewed by Ford at both DV and PV as listed above. Where flammability is required FMVSS 302 can be used instead of the ISO method. *Cold curl and Coefficient of friction are not applicable for trunk mats. * No surrogate test data is allowed for PV. ENGINEERING MATERIAL SPECIFICATION WSS-M15P44-B Copyright 2014, Ford Global Technologies, LLC Page 8 of 8 APPENDIX 1: Taber Abrasion Failure Criteria Figure 1: Unacceptable Taber Abrasion sample for tufted carpet. Figure 2: Acceptable Taber Abrasion sample for tufted carpet.