FORD WSH-M4D587-A-2005 POLYAMIDE (PA) 66 HEAT STABILIZED 20% GLASS FIBER REINFORCED ENGINE COOLANT RESISTANT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《耐发动机冷却液 20%玻璃纤维.pdf
《FORD WSH-M4D587-A-2005 POLYAMIDE (PA) 66 HEAT STABILIZED 20% GLASS FIBER REINFORCED ENGINE COOLANT RESISTANT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《耐发动机冷却液 20%玻璃纤维.pdf》由会员分享,可在线阅读,更多相关《FORD WSH-M4D587-A-2005 POLYAMIDE (PA) 66 HEAT STABILIZED 20% GLASS FIBER REINFORCED ENGINE COOLANT RESISTANT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《耐发动机冷却液 20%玻璃纤维.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2005 09 13 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.8, 3.9 & 4 1989 12 22 Released RD885100-281 C.F. Carter Printed copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 1 of 5 POLYAMIDE (PA) 66, HEAT STABILIZED, 20% GLAS
2、S WSH-M4D587-A FIBER REINFORCED, ENGINE COOLANT RESISTANT MOLDING COMPOUND 1. SCOPE The material defined by this specification is a glass fiber reinforced, heat stabilized and engine coolant resistant polyamide 66 injection molding compound. 2. APPLICATION This specification was released originally
3、for material used in the plastic radiator end tank drain cock. NOTICE: This material absorbs and retains moisture. Part design and tolerances must accommodate changes in part dimensions and physical properties due to moisture absorption or loss in the service/assembly environment. 3. REQUIREMENTS 3.
4、0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material and specimens with moisture
5、 content not exceeding 0.2% (test according to ISO 960, Method B/ASTM D 789). All test materials immediately after processing have to be sealed in containers that are impermeable to water vapor. If the moisture content exceeds 0.2%, condition the material for a minimum of 16 h at 40 - 50 C at a redu
6、ced pressure below 133 Pa. Conduct tests in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5% relative humidity. Individual specimens shall not be removed from closed containers until immediately before testing. 3.4 MOLDING COMPOUND 3.4.1 Glass Fiber Content 20 - 24% (ISO 3451/4, test temperature
7、600 +/- 25 C, test portion 1 g) 3.4.2 Melt Temperature 250 - 265 C (ISO 1218, Method B/ASTM D 789) 3.5 MOLDED TEST SPECIMEN 3.5.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on injection molded one-end gated test specimens. ENGINEERING MATERIAL SPECIFICATI
8、ONWSH-M4D587-A Printed copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 2 of 5 The following dimensions are required: A. 150 min x 10 x 4.0 +/- 0.2 mm (Tensile Bar, ISO 3167) B. 120 x 10 x 4.0 +/- 0.2 mm Specimens with shorter dimensions shall be cut from the center portion
9、 of the test specimen A and/or B. The specimens shall be prepared according to ISO 294. No annealing allowed. 3.5.2 Density 1.28 - 1.32 g/cm3(ISO 1183, Method A/ASTM D 792, Method A1) 3.5.3 Tensile Strength at Max Load, min 138 MPa (ISO R 527/ASTM D 638M, 150 min x 10 x 4.0 +/- 0.2 mm specimen, 5 mm
10、/min test speed) 3.5.4 Flexural Modulus, min 6.2 GPa (ISO 178/ASTM D 790M, Method I, Procedure A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 64 mm support span) 3.5.5 Shear Modulus at 23 C 1.10 - 1.70 GPa (ASTM D 4065, forced constant amplitude, fixed frequency of 1 Hz +/- 15%, strain level below 1%. Specim
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSHM4D587A2005POLYAMIDEPA66HEATSTABILIZED20GLASSFIBERREINFORCEDENGINECOOLANTRESISTANTMOLDINGCOMPOUNDTOBEUSEDWITHFORDWSSM99P1111A

链接地址:http://www.mydoc123.com/p-750274.html