FORD WRS-M3H153-A1-2014 CARPET POLYESTER ASHBURY PATTERN NON WOVEN RANDOM VELOUR NEEDLED MOLDABLE POLYETHYLENE MASS BACKED 585 g m2 (17 oz) MIN 100% PCR PIR CONTENT TO BE USED WIT.pdf

《FORD WRS-M3H153-A1-2014 CARPET POLYESTER ASHBURY PATTERN NON WOVEN RANDOM VELOUR NEEDLED MOLDABLE POLYETHYLENE MASS BACKED 585 g m2 (17 oz) MIN 100% PCR PIR CONTENT TO BE USED WIT.pdf》由会员分享，可在线阅读，更多相关《FORD WRS-M3H153-A1-2014 CARPET POLYESTER ASHBURY PATTERN NON WOVEN RANDOM VELOUR NEEDLED MOLDABLE POLYETHYLENE MASS BACKED 585 g m2 (17 oz) MIN 100% PCR PIR CONTENT TO BE USED WIT.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 00 2014 07 23 Released L. Sinclair, NA Controlled document at www.MATS Copyright 2014, Ford Global Technologies, Inc. Page 1 of 4 CARPET, POLYESTER, ASHBURY PATTERN WRS-M3H153-A1 NON WOVEN, RANDOM VELOUR, NEEDLED, MOLDABLE POLYETHYLENE, M

2、ASS BACKED 585 g/m2 (17 oz) MIN, 100% PCR/PIR CONTENT 1. SCOPE The materials defined by these specifications are random velour, needled, nonwoven carpets of good quality and uniform composition. The carpet face is made with 100% post consumer / post industrial fiber. 2. APPLICATION This specificatio

3、n was released originally for floor carpet applications on B and C car platforms as part of the GCBP strategy. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99

4、P1111-A). 3.1.1 In addition to the requirements listed herein, the end-item floor carpet shall be tested to WSS-M8P16-B and any additional SDS requirements. The details for each of the supplier specific construction shall be documented in the supplement attached and maintained in the scanned data pa

5、ckage. 3.1.2 Vehicle Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/ latest. Data must be provided by the Tier 1 at the appropriate program milestone. 3.1.3 Recycled Content This

6、 specification must contain 100% recycled content as defined by WRS- M99P42-A2 (Textile Materials, Identification of Recycled Content). ENGINEERING MATERIAL SPECIFICATION WRS-M3H153-A1 Copyright 2014, Ford Global Technologies, Inc. Page 2 of 4 3.2 SAMPLE SELECTION All evaluations shall be conducted

7、on test specimens taken from finished assemblies. 3.3 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. 3.4 COMPOSITION 3.4.1 Face Fiber 100% PIR/PCR Polyester (ASTM D276) UV Resistant

8、 3.4.2 Pre-Coat 100% Low Density (ASTM D276) Polyethylene 3.4.2 Mass Backing (WRS-M3H153-A2 only) EVA 3.5 METHOD OF DYEING Solution dyed 3.6 CONSTRUCTION 3.6.1 Face Fiber 12 Denier (ASTM D 1244) 3.7 THICKNESS (ISO 1765) Rolled Goods 5.0 +/- 0.5 mm Molded Product 5.0 + 0.5 / -1.0 mm 3.8 WEIGHT 3.8.1

9、Face Fiber 650 g/m2(19 oz) Nominal (ASTM D5848) (585 - 715) g/m2 (17 21) oz/yd2 3.8.2 Pre-Coat 77-94 g/m2 (2.2-2.8 oz/yd2) (ASTM D5848) 3.8.3 Mass Backing Report g/m2* (ASTM D276) * Mass backing weight is vehicle dependent. Approved mass backing weights will be documented on the Approved Source List

10、 (ASL) ENGINEERING MATERIAL SPECIFICATION WRS-M3H153-A1 Copyright 2014, Ford Global Technologies, Inc. Page 3 of 4 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Eng

11、ineering Material Specifications. 4.1 DRAWING CALL OUT The following shall be called out on the Engineering drawing to correctly designate the approved material. WRS-M3H153-A1 Supplier Name and Product Code (As it appears on the Approved Source Listing) WSS-M8P16-B 5. SUMMARY OF REVISIONS ENGINEERIN

12、G MATERIAL SPECIFICATION WRS-M3H153-A1 Copyright 2014, Ford Global Technologies, Inc. Page 4 of 4 Non Woven Carpet Construction Supplement Supplier _Supplier Contact Name_ Number _ Product/ Style Name _ Material Specification _ Performance Specification _ Supplier Product Code _ Manufacturing Locati

13、on _ Supplier Lab Number _ Supplier Lab Date _ Composition Type Supplier Face Fiber ASTM D276 _ _ Minimum Recycled Content _ % PIR _ % PCR Pre-Coat ASTM D276 _ _ Mass Backing ASTM D276 _ _ Construction Solution or piece dyed (circle one) Denier (s) _ Face Fiber Thickness ISO 1765 _+/- _ mm Pre Coating Thickness ISO 1765 _+/- _ mm Mass Backing Thickness ISO 1765 _+/- _ mm Mass per Unit Area Weight Face Fiber ASTM D5848 _+/- _ g/m2 Pre Coating ASTM D5848 _+/- _ g/m2 Mass Backing ASTM D5848 _+/- _ g/m2 Materials Engineering Signature _Date _ Comments _ Rolled Goods _ Molded Product _