FORD M2C151-A-2009 OIL - HOT MILL ROLLING《热轧用油》.pdf

《FORD M2C151-A-2009 OIL - HOT MILL ROLLING《热轧用油》.pdf》由会员分享，可在线阅读，更多相关《FORD M2C151-A-2009 OIL - HOT MILL ROLLING《热轧用油》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 04 14 N-STATUS No Replacement Named L. Sinclair, FNA 1986 08 01 Page 1 of 2 OIL - HOT MILL ROLLING M2C151-AB NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The material defined by this standard is a high pola

2、rity synthetic oil which is mixed with Hot Mill roll coolant water. 2. APPLICATION: This material is used as a plating oil for roll surface during the rolling of steel on the Hot Mills. 3. REQUIREMENTS: A B 3.1 VISCOSITY: at 100 F (40 C) 108.0-116.6 cSt 87.0-108.0 cSt (ASTM D 445 - D 2161) (500-540

3、SUS) (400-500 SUS) 3.2 VISCOSITY INDEX: 70 min 95 min (ASTM D 2270) 3.3 FLASH POINT: 400 F (204 C) min 425 F (218 C) min (ASTM D 92) 3.4 FIRE POINT: 410 F (210 C) min 450 F (232 C) min (ASTM D 92) 3.5 SAPONIFICATION NUMBER: 90 - 98 65 min (ASTM D 94) 3.6 FREE FATTY ACID: 6% max 3% max (ASTM D 128) 3

4、.7 COLOR: # 8 max # 8 max (ASTM D 1500) 3.8 WEIGHT PER GALLON: (LITRE) 7.5 lbs min 7.5 lbs min (ASTM D 891) (0.90 kg/L) (0.90 kg/L) 3.9 SUPPLIERS RESPONSIBILITY: All materials supplied to this standard must be equivalent in all characteristics to the material upon which approval was originally grant

5、ed, and shall be suitable for the intended application. Changes in composition shall not be made without approval of the responsible Staff Office in accordance with Manufacturing Procedure IId1. NON-PRODUCTION MATERIAL SPECIFICATION M2C151-AB Page 2 of 2 3.10 IDENTIFICATION: Materials supplied to th

6、is standard shall be identified with the “M“-number printed on the side as well as the top of the containers in letters at least 2“ (50 mm) high in a contrasting color to that of the container. Container marking shall be in accordance with Manufacturing Standard ZF-10 and conform to all Federal, Sta

7、te and Local container contents labeling regulations which are in effect both in the area of shipment and use. 4. APPROVAL OF NEW SUPPLIERS: Materials submitted by new manufacturers to this standard must have Regulatory Clearance, Laboratory and Shop Trial approvals. Suppliers are required to comple

8、te and submit the Material Health and Safety Data Sheet (Form 1291A) prior to Shop Trial. Recommendations for the addition of new manufacturers to the Manufacturing Approved Source List (ASL) must be made in writing to the responsible Manufacturing Staff Office by the appropriate divisional standard

9、s activity in accordance with Manufacturing Procedure IId1. 5. ENVIRONMENTAL CONTROL: Use of any material approved to this standard must comply with the guidelines as established in the environmental review of the material as they appear in the Materials and Toxicology System (MATS). 6. HEALTH AND SAFETY: Use of any material approved to this standard must comply with the guidelines given under the Toxicological (TOX) review of the material as indicated in the MATS system.