FORD FLTM BZ 154-01-2002 THREMOGRAVIMETRIC ANALYSIS (TGA) OF GASOLINE GUMS《汽油胶的热重量分析（TGA）》.pdf

《FORD FLTM BZ 154-01-2002 THREMOGRAVIMETRIC ANALYSIS (TGA) OF GASOLINE GUMS《汽油胶的热重量分析（TGA）》.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BZ 154-01-2002 THREMOGRAVIMETRIC ANALYSIS (TGA) OF GASOLINE GUMS《汽油胶的热重量分析（TGA）》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BZ 154-01 Date Action Revisions 2002 07 15 Activated C. Richardson Printed copies are uncontrolled Page 1 of 3 Copyright 2002, Ford Global Technologies, Inc. THERMOGRAVIMETRIC ANALYSIS (TGA) OF GASOLINE GUMS Application This test method describes the procedure for prepar

2、ing gum residues from gasoline containing detergent additives and the method for measuring the thermal decomposition of the gum residues. Significance and Use The method was developed as an alternative for conducting engine tests to assess the tendency of fuels formulated with detergent fuel additiv

3、es to buildup combustion chamber deposits in spark ignition engines. The gasoline gums consist of the polymeric detergent additives, carrier fluids and existent gums of gasoline components. The decomposition temperatures of the gum residues in the TGA test was found to give a reasonably good correla

4、tion with the buildup of combustion chamber deposits (CCD) in dynamometer tests. The fuels that were used to establish the correlation included commercial fuels from service stations and specially blended fuels that were formulated using several base gasolines and various detergent additive chemistr

5、ies and carrier fluids Summary of Test Method The unwashed gum of the gasoline sample is prepared per ASTM D 381 method3 and the sample is then heated in a TGA instrument at a constant rate of 5 C/ minute from 150 C to 500 C in an air environment. The thermal decomposition of the sample is analyzed

6、as a function of weight loss versus temperature. The first derivative of the TGA curve identifies critical peak temperatures where the majority of gum residues will decompose. Equipment Required Thermogravimetric Analyzer: A system of related instruments that is capable of continuously weighing a sa

7、mple under atmospheric control over a controlled temperature range for a defined period. The analyzer should have the capability to meet the conditions required for this method along with the software necessary to complete the required analyses. FORD LABORATORY TEST METHOD BZ 154-01 Page 2 of 3 Copy

8、right 2002, Ford Global Technologies, Inc. 1. Platinum sample pans of 100-L specimen size. 2. Methylene Chloride-ACS reagent grade 3. Dry Air, 99.9% purity Sample Preparation 1. Prepare a minimum of 15 mg of unwashed gum by evaporating 50 ml of gasoline per ASTM D 381 method. Two or more beakers of

9、fuel sample may be required to generate sufficient gum quantity. A maximum of 50 ml of gasoline shall be evaporated per beaker. Report the weight of unwashed gum for each beaker in mg/50ml of gasoline. 2. Add sufficient volume of methylene chloride to the gum beaker(s) and swirl gently to dissolve t

10、he gum. 3. Transfer sample into a tared vial with a pipette. 4. Repeat steps 2 and 3 until the methylene chloride is clear. 5. Evaporate the methylene chloride from each vial by air evaporation, steam bath or oven set at 40 C. Cover the vials with a paper towel or a loose fitting cap during evaporat

11、ion. 6. Wash the inside wall of the vials with methylene chloride so that all gum residue collects on the bottom of the vial. 7. After solvent has evaporated completely, place the lids on the vials, and reweigh. The net increase in weight after adding the gum residue to the tared vial should not be

12、significantly different from the total weight of unwashed gum collected in step 1 of this section. 8. Transfer the sample by adding an appropriate amount of methylene chloride to the vial. 9. Swirl sample in sealed vial for a few minutes to ensure that the sample is well mixed and all of the gum has

13、 dissolved. Note: The sample may collect on the vial wall if it is shaken too rapidly. Procedure 1. Transfer 10 -15 mg of gum to the TGA sample pan using sufficient solvent and record the weight of gum placed on the sample pan. 2. Establish the air atmosphere with flow set at 55 +/- 5 mL/min. FORD L

14、ABORATORY TEST METHOD BZ 154-01 Page 3 of 3 Copyright 2002, Ford Global Technologies, Inc. 3. Ramp temperature from 30 C to 150 C at rate of 5 C/min. 4. Maintain isothermal temperature at 150 C for 5 minutes. 5. Ramp temperature from 150 C to 500 C at a rate of 5 C/minute. Calibration 1. Calibrate t

15、he TGA for temperature using a minimum of two calibration standards. 2. Clean oven and sample holder per operating manual. 3. Platinum sample pans are reusable and should be thoroughly cleaned. 4. Aluminum sample pans shall be discarded after each test. Quality Control/Quality Assurance A QC/QA cali

16、bration check should be performed at least once per day on TGA instrument to calibrate temperature using a minimum of two calibration standards. Data Analysis 1. Convert binary data from TGA instrument to ASCII data format. 2. Plot TGA results: - Plot temperature (C) on X-axis versus the weight % re

17、maining of gum residue on Y1-axis. - Plot temperature (C) on X-axis versus the derivative weight (% weight / minute) on Y2-axis. Reference 1. SAE Paper 962012, Evaluation of the Effect of Fuel Composition and Gasoline Additives on Combustion Chamber Deposits 2. ASTM D6201-99, Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation 3. ASTM D 381-01, Standard Test Method for Gum Content in Fuels by Jet Evaporation